Merge tag 'mac80211-for-davem-2015-04-01' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211

Johannes Berg says:

====================
This contains just a single fix for a crash I happened to randomly
run into today during testing. It's clearly been around for a while,
but is pretty hard to trigger, even when I tried explicitly (and
modified the code to make it more likely) it rarely did.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
bnx2x: kdump related fixes

This patch series aims to fix bnx2x driver issues when loading in kdump kernel.
Both issues fixed here would be fatal to the device, requiring full reset of
the system in order to recover, preventing the device from serving its purpose
in the kdump environment.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When IOMM-vtd is active, once main kernel crashes unfinished DMAE transactions
will be blocked, putting the HW in an error state which will cause further
transactions to timeout.

Current employed logic uses wrong macros, causing the first function to be the
only function that cleanups that error state during its probe/load.

This patch allows all the functions to successfully re-load in kdump kernel.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running in a kdump kernel, it's very likely that due to sync. loss with
management firmware the first PCI function to probe and reach the previous
unload flow would decide it can reset the chip and continue onward. While doing
so, it will only close its own Rx port.

On a 4-port device where 2nd port on engine is a 1g-port, the 2nd port would
allow ingress traffic after the chip is reset [assuming it was active on the
first kernel]. This would later cause a HW attention.

This changes driver flow to close both ports' 1g capabilities during the
previous driver unload flow prior to the chip reset.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:

 * tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
 * station is destroyed
 * reorder timer fires before ieee80211_free_tid_rx() runs,
   accessing the station, thus potentially crashing due to
   the use-after-free

The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.

Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Update the git tree info with a recent change in tree names.  Also
add our new mailing list created solely for Linux kernel patches
and kernel development, as well as the new patchwork project for
tracking patches.  Lastly update the list of "reviewers" since a
couple of developers have moved on to different projects.

Made an update to the section header so that it is more manageable
going forward as we add new drivers.
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When remove TIPC module, there is a warning to remind us that a slab
object is leaked like:

root@localhost:~# rmmod tipc
[   19.056226] =============================================================================
[   19.057549] BUG TIPC (Not tainted): Objects remaining in TIPC on kmem_cache_close()
[   19.058736] -----------------------------------------------------------------------------
[   19.058736]
[   19.060287] INFO: Slab 0xffffea0000519a00 objects=23 used=1 fp=0xffff880014668b00 flags=0x100000000004080
[   19.061915] INFO: Object 0xffff880014668000 @offset=0
[   19.062717] kmem_cache_destroy TIPC: Slab cache still has objects

This is because the listening socket of TIPC topology server is not
closed before TIPC proto handler is unregistered with proto_unregister().
However, as the socket is closed in tipc_exit_net() which is called by
unregister_pernet_subsys() during unregistering TIPC namespace operation,
the warning can be eliminated if calling unregister_pernet_subsys() is
moved before calling proto_unregister().

Fixes: e05b31f4 ("tipc: make tipc socket support net namespace")
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This device is sold as 'Lenovo Tinkpad USB 3.0 Ethernet 4X90E51405'.
Chipset is RTL8153 and works with r8152.
Signed-off-by: NChristian Hesse <mail@eworm.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sending over AF_IUCV socket, errno was incorrectly set to
ENOMEM even when other values where appropriate, notably EAGAIN.
With this patch, error indicator returned by sock_alloc_send_skb()
is passed to the caller, rather than being overwritten with ENOMEM.
Signed-off-by: NEugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return module reference before invoking the respective vport
->destroy() function. This is needed as ovs_vport_del() is not
invoked inside an RCU read side critical section so the kfree
can occur immediately before returning to ovs_vport_del().

Returning the module reference before ->destroy() is safe because
the module unregistration is blocked on ovs_lock which we hold
while destroying the datapath.

Fixes: 62b9c8d0 ("ovs: Turn vports with dependencies into separate modules")
Reported-by: NPravin Shelar <pshelar@nicira.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is especially important in cases where the kernel allocs a new
structure and expects a field to be set from a netlink attribute. If such
attribute is shorter than expected, the rest of the field is left containing
previous data. When such field is read back by the user space, kernel memory
content is leaked.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before commit 3900f290 ("bonding: slight
optimizztion for bond_slave_override()") the override logic was to send packets
with non-zero queue_id through the slave with corresponding queue_id, under two
conditions only - if the slave can transmit and it's up.

The above mentioned commit changed this logic by introducing an additional
condition - whether the bond is active (indirectly, using the slave_can_tx and
later - bond_is_active_slave), that prevents the user from implementing more
complex policies according to the Documentation/networking/bonding.txt.
Signed-off-by: NAnton Nayshtut <anton@swortex.com>
Signed-off-by: NAlexey Bogoslavsky <alexey@swortex.com>
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Benc says:

====================
ipvlan: list corruption and rcu fixes

This patch set fixes different issues leading to corrupted lists and
incorrect rcu usage.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an ipvlan interface is down, its addresses are not on the hash list.
Fix checks for existence of addresses not to depend on the hash list, walk
through all interface addresses instead.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Acked-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All accesses to ipvlan->addrs are under rtnl.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding and removing to the 'ipvlans' list is already done using _rcu list
operations.
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When ipvlan interface with IP addresses attached is brought down and then
deleted, the assigned addresses are deleted twice from the address hash
list, first on the interface down and second on the link deletion.
Similarly, when an address is added while the interface is down, it is added
second time once the interface is brought up.

When the interface is down, the addresses should be kept off the hash list
for performance reasons. Ensure this is true, which also fixes the double add
problem. To fix the double free, check whether the address is hashed before
removing it.
Reported-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FEC modules used on i.MX28 and newer have a register to tune the MDIO
output hold time that should be at least 10 ns. Up to now this value was not
explicitly set and so resulted in less hold time if the fec clock was
faster than 100 MHz.

This was noticed on an i.MX28 machine that uses an input clock of ~150
Mhz which resulted in unreliable communication with a Marvell switch.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_v6_fill_cb() will be called twice if socket's state changes from
TCP_TIME_WAIT to TCP_LISTEN. That can result in control buffer data
corruption because in the second tcp_v6_fill_cb() call it's not copying
IP6CB(skb) anymore, but 'seq', 'end_seq', etc., so we can get weird and
unpredictable results. Performance loss of up to 1200% has been observed
in LTP/vxlan03 test.

This can be fixed by copying inet6_skb_parm to the beginning of 'cb'
only if xfrm6_policy_check() and tcp_v6_fill_cb() are going to be
called again.

Fixes: 2dc49d16 ("tcp6: don't move IP6CB before xfrm6_policy_check()")
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes sparse warnings introduced in commit e85c9a7a ("cxgb4/cxgb4vf: Add
code to calculate T5 BAR2 Offsets for SGE Queue Registers") and
df64e4d3 ("cxgb4/cxgb4vf: Use new interfaces to calculate BAR2 SGE Queue
Register addresses") and few old ones

sparse warnings:
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: cast removes
>> address space of expression
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1006:48: sparse: incorrect type in
>> initializer (different address space)
>> drivers/net/ethernet/chelsio/cxgb4vf/sge.c:1020:40: sparse: incorrect type in
>> argument 1 (different base types)
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the current code, ids are removed too early.
Suppose you have an ipip interface that stands in the netns foo and its link
part in the netns bar (so the netns bar has an nsid into the netns foo).
Now, you remove the netns bar:
 - the bar nsid into the netns foo is removed
 - the netns exit method of ipip is called, thus our ipip iface is removed:
   => a netlink message is sent in the netns foo to advertise this deletion
   => this netlink message requests an nsid for bar, thus a new nsid is
      allocated for bar and never removed.

We must remove nsids when we are sure that nobody will refer to netns currently
cleaned.

Fixes: 0c7aecd4 ("netns: add rtnl cmd to add and get peer netns ids")
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hariprasad Shenai says:

====================
cxgb4: Fixes ingress queue mapping and other fixes

The below series fixes ingress queue mapping by allocating them dynamically to
prevent stack overflow. Disable napi and interrupts before unregistering netdev
to avoid crash while unloading driver when traffic is flowing.

The patches series is created against 'net' tree.
And includes patches on cxgb4 driver.

We have included all the maintainers of respective drivers. Kindly review the
change and let us know in case of any review comments.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable interrupts and quiesce rx before unregistering net device to avoid crash
while unloading driver when traffic is flowing through.

Based on original work by Shameem Khalid <shameem@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QIDs (egress/ingress) from firmware in FW_*_CMD.alloc command
can be anywhere in the range from EQ(IQFLINT)_START to EQ(IQFLINT)_END.
For eg, in the first load eqid can be from 100 to 300.
In the next load it can be from 301 to 500 (assume eq_start is 100 and eq_end is
1000).

The driver was assuming them to always start from EQ(IQFLINT)_START till
MAX_EGRQ(INGQ). This was causing stack overflow and subsequent crash.

Fixed it by dynamically allocating memory (of qsize (x_END - x_START + 1)) for
these structures.

Based on original work by Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

cdc_ncm disagrees with usbnet about how much framing overhead should
be counted in the tx_bytes statistics, and tries 'fix' this by
decrementing tx_bytes on the transmit path.  But statistics must never
be decremented except due to roll-over; this will thoroughly confuse
user-space.  Also, tx_bytes is only incremented by usbnet in the
completion path.

Fix this by requiring drivers that set FLAG_MULTI_FRAME to set a
tx_bytes delta along with the tx_packets count.

Fixes: beeecd42 ("net: cdc_ncm/cdc_mbim: adding NCM protocol statistics")
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NBjørn Mork <bjorn@mork.no>

Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.

cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.

Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes below warning by dynamically allocating memory

All warnings:

   drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c: In function
   'cctrl_tbl_show':
   >> drivers/net/ethernet/chelsio/cxgb4/cxgb4_debugfs.c:689:1: warning: the
   >> frame
   >> size of 1028 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A local route may have a lower hop_limit set than global routes do.

RFC 3756, Section 4.2.7, "Parameter Spoofing"

>   1.  The attacker includes a Current Hop Limit of one or another small
>       number which the attacker knows will cause legitimate packets to
>       be dropped before they reach their destination.

>   As an example, one possible approach to mitigate this threat is to
>   ignore very small hop limits.  The nodes could implement a
>   configurable minimum hop limit, and ignore attempts to set it below
>   said limit.
Signed-off-by: ND.S. Ljungmark <ljungmark@modio.se>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ucc_geth was indicating link up after a port is administratively enabled even
when nothing is plugged in.  This causes user-space tools to see a spurious link
up the first time after boot.
Signed-off-by: NCliff Clark <cliff_clark@selinc.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4 driver RC fixes

Ido's patch should go to -stable of >= 3.14 too, the issue is older but it
hits us with VXLAN for which driver support dates there.

As for Jack's fix, for the time being, picking it to 4.0 is OK.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We occasionally see in procedure mlx4_GEN_EQE that the driver tries
to grab an uninitialized mutex.

This can occur in only one of two ways:
1. We are trying to generate an async event on an uninitialized slave.
2. We are trying to generate an async event on an illegal slave number
   ( < 0 or > persist->num_vfs) or an inactive slave.

To deal with #1: move the mutex initialization from specific slave init
sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that
the mutex is always initialized for all slaves).

To deal with #2: check in procedure mlx4_GEN_EQE that the slave number
provided is in the proper range and that the slave is active.
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.

For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.

Fixes: 837052d0 ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: NIdo Shamay <idos@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-for-davem-2015-03-24' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers

iwlwifi:

* avoid panic with lots of IBSS stations
* Fix dvm's behavior after suspend resume
* Allow to keep connection after CSA failure
* Remove a noisy by harmless WARN_ON
* New device IDs

rtlwifi:

* fix IOMMU mapping leak in AP mode

brcmfmac:

* disable MBSS feature for BCM43362 to get AP mode working again

ath9k:

* disable Transmit Power Control (TPC) again due to regressions

* fix beaconing issue with AP+STA setup
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Master change notifications may occur other than when joining or
leaving a bridge, for example when being added to or removed from
a bond or Open vSwitch.

Previously in those cases rocker_port_bridge_leave() was called
which results in a null-pointer dereference as rocker_port->bridge_dev
is NULL because there is no bridge device.

This patch makes provision for doing nothing in such cases.

Fixes: 6c707945 ("rocker: implement L2 bridge offloading")
Acked-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case we move the whole dev group to another netns,
we should call for_each_netdev_safe(), otherwise we get
a soft lockup:

 NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [ip:798]
 irq event stamp: 255424
 hardirqs last  enabled at (255423): [<ffffffff81a2aa95>] restore_args+0x0/0x30
 hardirqs last disabled at (255424): [<ffffffff81a2ad5a>] apic_timer_interrupt+0x6a/0x80
 softirqs last  enabled at (255422): [<ffffffff81079ebc>] __do_softirq+0x2c1/0x3a9
 softirqs last disabled at (255417): [<ffffffff8107a190>] irq_exit+0x41/0x95
 CPU: 0 PID: 798 Comm: ip Not tainted 4.0.0-rc4+ #881
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 task: ffff8800d1b88000 ti: ffff880119530000 task.ti: ffff880119530000
 RIP: 0010:[<ffffffff810cad11>]  [<ffffffff810cad11>] debug_lockdep_rcu_enabled+0x28/0x30
 RSP: 0018:ffff880119533778  EFLAGS: 00000246
 RAX: ffff8800d1b88000 RBX: 0000000000000002 RCX: 0000000000000038
 RDX: 0000000000000000 RSI: ffff8800d1b888c8 RDI: ffff8800d1b888c8
 RBP: ffff880119533778 R08: 0000000000000000 R09: 0000000000000000
 R10: 0000000000000000 R11: 000000000000b5c2 R12: 0000000000000246
 R13: ffff880119533708 R14: 00000000001d5a40 R15: ffff88011a7d5a40
 FS:  00007fc01315f740(0000) GS:ffff88011a600000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 00007f367a120988 CR3: 000000011849c000 CR4: 00000000000007f0
 Stack:
  ffff880119533798 ffffffff811ac868 ffffffff811ac831 ffffffff811ac828
  ffff8801195337c8 ffffffff811ac8c9 ffff8801195339b0 ffff8801197633e0
  0000000000000000 ffff8801195339b0 ffff8801195337d8 ffffffff811ad2d7
 Call Trace:
  [<ffffffff811ac868>] rcu_read_lock+0x37/0x6e
  [<ffffffff811ac831>] ? rcu_read_unlock+0x5f/0x5f
  [<ffffffff811ac828>] ? rcu_read_unlock+0x56/0x5f
  [<ffffffff811ac8c9>] __fget+0x2a/0x7a
  [<ffffffff811ad2d7>] fget+0x13/0x15
  [<ffffffff811be732>] proc_ns_fget+0xe/0x38
  [<ffffffff817c7714>] get_net_ns_by_fd+0x11/0x59
  [<ffffffff817df359>] rtnl_link_get_net+0x33/0x3e
  [<ffffffff817df3d7>] do_setlink+0x73/0x87b
  [<ffffffff810b28ce>] ? trace_hardirqs_off+0xd/0xf
  [<ffffffff81a2aa95>] ? retint_restore_args+0xe/0xe
  [<ffffffff817e0301>] rtnl_newlink+0x40c/0x699
  [<ffffffff817dffe0>] ? rtnl_newlink+0xeb/0x699
  [<ffffffff81a29246>] ? _raw_spin_unlock+0x28/0x33
  [<ffffffff8143ed1e>] ? security_capable+0x18/0x1a
  [<ffffffff8107da51>] ? ns_capable+0x4d/0x65
  [<ffffffff817de5ce>] rtnetlink_rcv_msg+0x181/0x194
  [<ffffffff817de407>] ? rtnl_lock+0x17/0x19
  [<ffffffff817de407>] ? rtnl_lock+0x17/0x19
  [<ffffffff817de44d>] ? __rtnl_unlock+0x17/0x17
  [<ffffffff818327c6>] netlink_rcv_skb+0x4d/0x93
  [<ffffffff817de42f>] rtnetlink_rcv+0x26/0x2d
  [<ffffffff81830f18>] netlink_unicast+0xcb/0x150
  [<ffffffff8183198e>] netlink_sendmsg+0x501/0x523
  [<ffffffff8115cba9>] ? might_fault+0x59/0xa9
  [<ffffffff817b5398>] ? copy_from_user+0x2a/0x2c
  [<ffffffff817b7b74>] sock_sendmsg+0x34/0x3c
  [<ffffffff817b7f6d>] ___sys_sendmsg+0x1b8/0x255
  [<ffffffff8115c5eb>] ? handle_pte_fault+0xbd5/0xd4a
  [<ffffffff8100a2b0>] ? native_sched_clock+0x35/0x37
  [<ffffffff8109e94b>] ? sched_clock_local+0x12/0x72
  [<ffffffff8109eb9c>] ? sched_clock_cpu+0x9e/0xb7
  [<ffffffff810cadbf>] ? rcu_read_lock_held+0x3b/0x3d
  [<ffffffff811ac1d8>] ? __fcheck_files+0x4c/0x58
  [<ffffffff811ac946>] ? __fget_light+0x2d/0x52
  [<ffffffff817b8adc>] __sys_sendmsg+0x42/0x60
  [<ffffffff817b8b0c>] SyS_sendmsg+0x12/0x1c
  [<ffffffff81a29e32>] system_call_fastpath+0x12/0x17

Fixes: e7ed828f ("netlink: support setting devgroup parameters")
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On s390x, gcc 4.8 compiles this part of tcp_v6_early_demux()

        struct dst_entry *dst = sk->sk_rx_dst;

        if (dst)
                dst = dst_check(dst, inet6_sk(sk)->rx_dst_cookie);

to code reading sk->sk_rx_dst twice, once for the test and once for
the argument of ip6_dst_check() (dst_check() is inline). This allows
ip6_dst_check() to be called with null first argument, causing a crash.

Protect sk->sk_rx_dst access by READ_ONCE() both in IPv4 and IPv6
TCP early demux code.

Fixes: 41063e9d ("ipv4: Early TCP socket demux.")
Fixes: c7109986 ("ipv6: Early TCP socket demux")
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Statistics' state-machine in bnx2x driver must be synced with various driver
flows, but its current locking scheme manages to be wasteful [using 2 locks +
additional local variable] and prone to race-conditions at the same time,
as the state-machine and 'action' are being accessed under different locks.

In addition, current 'safe exec' isn't in fact safe, since the only guarantee
it gives is that DMA transactions are over, but ramrods might still be running.

This patch cleans up said logic, leaving us with a single lock for the entire
flow and removing the possible races.

Changes from v2:
	- Switched into mutex locking from semaphore locking.
	- Release locks on error flows.

Changes from v1:
	Failure to acquire lock fails flow instead of printing a warning and
	allowing access to the critical section.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'linux-can-fixes-for-4.0-20150322' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can

Marc Kleine-Budde says:

====================
pull-request: can 2015-03-22

this is a pull-request of 7 patches for net/master.

Ahmed S. Darwish fixes another two problems in the kvaser_usb driver. A patch
by Colin Ian King for the gs_usb driver adds a missing check for kzalloc
allocation failures. Two patches by Stephane Grosjean for the peak_usb driver
add missing support for ISO / non-ISO mode switching. Andri Yngvason
contributes a patch to fix the state handling in the flexcan driver. The last
patch by Andreas Werner for the flexcan driver add missing EPROBE_DEFER
handling for the transceiver regulator.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Validate iov ranges before feeding them into iov_iter_init(), from
    Al Viro.

 2) We changed copy_from_msghdr_from_user() to zero out the msg_namelen
    is a NULL pointer is given for the msg_name.  Do the same in the
    compat code too.  From Catalin Marinas.

 3) Fix partially initialized tuples in netfilter conntrack helper, from
    Ian Wilson.

 4) Missing continue; statement in nft_hash walker can lead to crashes,
    from Herbert Xu.

 5) tproxy_tg6_check looks for IP6T_INV_PROTO in ->flags instead of
    ->invflags, fix from Pablo Neira Ayuso.

 6) Incorrect memory account of TCP FINs can result in negative socket
    memory accounting values.  Fix from Josh Hunt.

 7) Don't allow virtual functions to enable VLAN promiscuous mode in
    be2net driver, from Vasundhara Volam.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  netfilter: nft_compat: set IP6T_F_PROTO flag if protocol is set
  cx82310_eth: wait for firmware to become ready
  net: validate the range we feed to iov_iter_init() in sys_sendto/sys_recvfrom
  net: compat: Update get_compat_msghdr() to match copy_msghdr_from_user() behaviour
  be2net: use PCI MMIO read instead of config read for errors
  be2net: restrict MODIFY_EQ_DELAY cmd to a max of 8 EQs
  be2net: Prevent VFs from enabling VLAN promiscuous mode
  tcp: fix tcp fin memory accounting
  ipv6: fix backtracking for throw routes
  net: ethernet: pcnet32: Setup the SRAM and NOUFLO on Am79C97{3, 5}
  ipv6: call ipv6_proxy_select_ident instead of ipv6_select_ident in udp6_ufo_fragment
  netfilter: xt_TPROXY: fix invflags check in tproxy_tg6_check()
  netfilter: restore rule tracing via nfnetlink_log
  netfilter: nf_tables: allow to change chain policy without hook if it exists
  netfilter: Fix potential crash in nft_hash walker
  netfilter: Zero the tuple in nfnl_cthelper_parse_tuple()