Add a sysfs led class interface to the led subdriver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Add a sysfs led class interface to the thinklight (light subdriver).
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Do some preparatory work to add sysfs support to the thinklight and
thinkpad leds driver.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Unfortunately, a lot of stuff in the kernel has size limitations, so
"thinkpad-acpi" ends up eating up too much real estate.  We were using
"tpacpi" in symbols already, but this shorthand was not visible to
userland.

Document that the driver will use tpacpi as a short hand where necessary,
and use it to name the kernel thread for NVRAM polling (now named
"ktpacpi_nvramd").

Also, register a module alias with the shorthand.  One can refer to the
module using the shorthand name.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

ibm-acpi and thinkpad-acpi did not know about bit 5 of the EC backlight
level control register (EC 0x31), so it was always forced to zero on
any writes.

This would disable the BIOS option to *not* use a dimmer backlight level
scale while on battery, and who knows what else (there are two other
control bits of unknown function).

Bit 5 controls the "reduce backlight levels when on battery" optional
functionality (active low).  Bits 6 and 7 are better left alone as well,
instead of being forced to zero.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

If userspace applications mess with the CMOS NVRAM, or something causes
both the ACPI firmware and thinkpad-acpi to try to change the brightness at
the same time, it is possible to have the CMOS and EC registers for the
current brightness go out of sync.

Should that happen, thinkpad-acpi could be really obnoxious when using a
brightness_mode of 3 (both EC and CMOS).  Instead of complaining a massive
number of times, make sure to complain only once until EC and CMOS are back
in sync.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Joerg Platte <lists@naasa.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

During initialization, thinkpad-acpi outputs some messages to make sure
releavant box identification information is easily available in-line with
the rest of the driver messages.

Enhance those messages to output the alfanumeric model number as well.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

thinkpad-acpi knows for a while now how to best program the hotkeys by
default, and always enable them by default.  Unfortunately, this
information has not filtered down everywhere it needs to, yet.  Notably,
old ibm-acpi documentation and most "thinkpad setup guides" will have wrong
information on this area.

Warn the local admin once whenever any of the following patterns are met:

1. Attempts to set hotkey mask to 0xffff (artifact from docs and config
   for the old ibm-acpi driver and behaviour).  This mask makes no
   real-world sense;

2. Attempts to set hotkey mask to 0xffffffff, which means the user is
   trying to just have "everything work" without even reading the
   documentation, or that we need to get a bug report, because there
   is a new thinkpad out there with new exciting hot keys :-)

3. Attempts to set hotkey mask to 0xffffff, which is almost never the
   correct way to set up volume and brightness event reporting (and with
   the current state-of-the-art, it is known to never be right way to do
   it).

The driver will perform any and all requested operations, though,
regardless of any warnings.  I hope these warnings can be removed one or
two years from now.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: NLen Brown <len.brown@intel.com>

Lenovo ThinkPads with generic ACPI backlight level control can be easily
set to react to keyboard brightness key presses in a more predictable way
than what they do when in "DOS / bootloader" mode after Linux brings
up the ACPI interface.

The switch to the ACPI backlight mode in the firmware is designed to be
safe to use only as an one way trapdoor.  One is not to force the firmware
to switch back to "DOS/bootloader" mode except by rebooting.  The mode
switch itself is performed by calling any of the ACPI _BCL methods at least
once.

When in ACPI mode, the backlight firmware just issues (standard) events for
the brightness up/down hot key presses along with the non-standard HKEY
events which thinkpad-acpi traps, and doesn't touch the hardware.

thinkpad-acpi will:

1. Place the ThinkPad firmware in ACPI backlight control mode
   if one is available
2. Suppress HKEY backlight change notifications by default
   to avoid double-reporting when ACPI video is loaded when
   the ThinkPad is in ACPI backlight control mode
3. Urge the user to load the ACPI video driver

The user is free to use either the ACPI video driver to get the brightness
key events, or to override the thinkpad-acpi default hotkey mask to get
them from thinkpad-acpi as well (this will result in duplicate events if
ACPI video is loaded, so let's hope distros won't screw this up).

Provided userspace is sane, all should work (and *keep* working), which is
more that can be said about the non-ACPI mode of the new Lenovo ThinkPad
BIOSes when coupled to current userspace and X.org drivers.

Full guidelines for backlight hot key reporting and use of the
thinkpad-acpi backlight interface have been added to the documentation.
Signed-off-by: NHenrique de Moraes Holschuh <hmh@hmh.eng.br>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/media/video/v4l2-common.c:719:16: warning: Using plain integer as NULL pointer
drivers/media/video/au0828/au0828-dvb.c:122:19: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1101:22: warning: Using plain integer as NULL pointer
drivers/media/video/ivtv/ivtv-yuv.c:1102:23: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-audio.c:78:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-video-v4l.c:84:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-v4l2.c:1264:9: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-context.c:197:28: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-cx2584x-v4l.c:126:39: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:133:32: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:145:31: warning: Using plain integer as NULL pointer
drivers/media/video/pvrusb2/pvrusb2-dvb.c:177:55: warning: Using plain integer as NULL pointer
drivers/media/video/videobuf-core.c:100:9: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

drivers/scsi/aic7xxx/aic7770_osm.c:53:58: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:355:47: warning: Using plain integer as NULL pointer
drivers/scsi/aic7xxx/aic7xxx_osm_pci.c:372:55: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:997:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1003:28: warning: Using plain integer as NULL pointer
drivers/scsi/aha152x.c:1165:46: warning: Using plain integer as NULL pointer
drivers/scsi/fdomain.c:1446:40: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:1650:51: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:3171:42: warning: Using plain integer as NULL pointer
drivers/scsi/sym53c8xx_2/sym_hipd.c:5732:52: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8189:31: warning: Using plain integer as NULL pointer
drivers/scsi/ncr53c8xx.c:8225:34: warning: Using plain integer as NULL pointer
drivers/scsi/dpt_i2o.c:156:32: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:954:42: warning: Using plain integer as NULL pointer
drivers/scsi/ultrastor.c:1104:18: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (35 commits)
  siimage: coding style cleanup (take 2)
  ide-cd: clean up cdrom_analyze_sense_data()
  ide-cd: fix test unsigned var < 0
  ide: add TSSTcorp CDDVDW SH-S202H to ivb_list[]
  piix: add Asus Eee 701 controller to short cable list
  ARM: always select HAVE_IDE
  remove the broken ETRAX_IDE driver
  ide: remove ->dma_prdtable field from ide_hwif_t
  ide: remove ->dma_vendor{1,3} fields from ide_hwif_t
  scc_pata: add ->dma_host_set and ->dma_start methods
  ide: skip "VLB sync" if host uses MMIO
  ide: add ide_pad_transfer() helper
  ide: remove ->INW and ->OUTW methods
  ide: use IDE I/O helpers directly in ide_tf_{load,read}()
  ns87415: add ->tf_read method
  scc_pata: add ->tf_{load,read} methods
  ide-h8300: add ->tf_{load,read} methods
  ide-cris: add ->tf_{load,read} methods
  ide: add ->tf_load and ->tf_read methods
  ide: move ide_tf_{load,read} to ide-iops.c
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild:
  kconfig: add named choice group
  kconfig: fix choice dependency check
  kconifg: 'select' considered less evil
  dontdiff: ignore timeconst.h
  dontdiff: add modules.order
  kbuild: fix unportability in gen_initramfs_list.sh
  kbuild: fix help output to show correct arch
  kbuild: show defconfig subdirs in make help
  kconfig: reversed borderlines in inputbox

drivers/atm/nicstar.c:418:25: warning: Using plain integer as NULL pointer
drivers/char/drm/r128_cce.c:820:25: warning: Using plain integer as NULL pointer
drivers/char/tty_io.c:1183:10: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

mm/hugetlb.c:207:11: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

kernel/cpuset.c:1268:52: warning: Using plain integer as NULL pointer
kernel/pid_namespace.c:95:24: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Reviewed-by: NPaul Jackson <pj@sgi.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

init/do_mounts_rd.c:215:13: warning: Using plain integer as NULL pointer
init/do_mounts_md.c:136:45: warning: Using plain integer as NULL pointer
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix 18 errors and several warnings given by checkpatch.pl:

- use of C99 // comments;

- trailing whitespace;

- 'switch' and 'case' not at the same indentation level;

- no space before the open parenthesis of the 'if' and 'switch' statements;

- space between function name and open parenthesis (though I have introduced
  such warnins in some places since the code looks prettier with the spaces);

- including <asm/io.h> instead of <linux/io.h>;

- line over 80 characters.

In addition to these changes, also do the following:

- make the arrays in sil_set_pio_mode() 'static', and make the arrays in
  sil_set_dma_mode() 'static const';

- change the string of the 'if' statements into the 'switch' statement in
  sil_pata_udma_filter();

- drop the needless '==' operators from the 'if' statements where a condition
  is a mere bit test;

- remove needless initializer for the 'tmp' variable in init_chipset_siimage();

- beautify groups of the variable initializers and assignment operators;

- add new line after variable definitions;

- remove new line between the comment and the statements it refers to;

- remove needless curly braces and parentheses;

- fix typos, capitalize acronyms, etc. in the comments...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

[bart: fix handling of bio_sectors(failed_command->bio) == 0]
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

valid is unsigned and cannot be below 0.
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Based on ata_piix patch by Dan McGee.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

It's plain wrong for PCMCIA to select HAVE_IDE that implies e.g. the
availability of an asm/ide.h

It turns out this was done for ARM, and we can simply always select 
HAVE_IDE on ARM instead of manually tracking which platforms might 
possible have an IDE controller directly or indirectly.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Russell King <rmk+lkml@arm.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

ETRAX_IDE was marked as broken last year with the comment
"it doesn't even compile currently".

Remove it since it won't get fixed in the near future.

On Mon, Apr 14, 2008 at 02:50:19PM +0200, Mikael Starvik wrote:
> You can remove it for now and we will resubmit a new if/when we get around
> to fix it.

[bart: ported it over IDE tree]
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jesper Nilsson <Jesper.Nilsson@axis.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use 'hwif->dma_base + {4,8}' instead of hwif->dma_prdtable in
  {ide,scc}_dma_setup().

* Remove no longer needed ->dma_prdtable field from ide_hwif_t.

While at it:

* Use ATA_DMA_TABLE_OFS define.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use 'hwif->dma_base + {1,3}' instead of hwif->dma_vendor{1,3} in
  pdc202xx_new host driver.

* Remove no longer needed ->dma_vendor{1,3} fields from ide_hwif_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->dma_host_set and ->dma_start methods (+ __scc_dma_end() helper)
so scc_ide_{in,out}b() can be used directly.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.

* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
  'ide_drive_t *drive' argument.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ide_pad_transfer() helper (which uses ->{in,out}put_data methods
  internally so the transfer is also padded to drive+host requirements)
  and use it instead of ide_atapi_{write_zeros,discard_data}().

* Remove no longer needed ide_atapi_{write_zeros,discard_data}().

Cc: Borislav Petkov <petkovbb@gmail.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remove no longer used ->INW and ->OUTW methods.

While at it:

* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
  so inline it there.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->tf_read method so out{b,w}(), in{b,w}() and superio_ide_inb()
can be used directly.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->tf_{load,read} methods so scc_ide_{outb,outw,inb,inw}()
can be used directly.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->tf_{load,read} methods so outb()/inb() and mm_outw()/mm_inw()
can be used directly.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ->tf_{load,read} methods so cris_ide_{outb,outw,inb,inw}()
can be used directly.

There should be no functional changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
  methods in default_hwif_transport().

* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.

* Make ide_tf_{load,read}() static.

There should be no functional changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Factor out debugging code from ide_tf_load() to ide_tf_dump() helper
and update ide_tf_load() users accordingly.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.

As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>