- 21 12月, 2008 11 次提交
-
-
由 Wolfram Sang 提交于
Add RTS/CTS-support for the PSC of the MPC5200B. Tested with a Phytec MPC5200B-IO. Signed-off-by: NWolfram Sang <w.sang@pengutronix.de> Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Grant Likely 提交于
This patch adds documentation to the mpc5200 interrupt controller driver and cleans up some minor coding conventions. It also moves the contents of mpc52xx_pic.h into the driver proper (except for a small common bit that is moved to the common mpc52xx.h) because the information encoded there is not required by any other part of kernel code. Finally for code readability sake, the L2_OFFSET shift value is removed because the code using it resolves to a noop. Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
-
由 Grant Erickson 提交于
Add const qualifier to device_node argument for dcr_resource_{start,len} as of_get_property also const-qualifies this argument. Signed-off-by: NGrant Erickson <gerickson@nuovations.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
Currently, we never set _PAGE_COHERENT in the PTEs, we just OR it in in the hash code based on some CPU feature bit. We also manipulate _PAGE_NO_CACHE and _PAGE_GUARDED by hand in all sorts of places. This changes the logic so that instead, the PTE now contains _PAGE_COHERENT for all normal RAM pages thay have I = 0 on platforms that need it. The hash code clears it if the feature bit is not set. It also adds some clean accessors to setup various valid combinations of access flags and change various bits of code to use them instead. This should help having the PTE actually containing the bit combinations that we really want. I also removed _PAGE_GUARDED from _PAGE_BASE on 44x and instead set it explicitely from the TLB miss. I will ultimately remove it completely as it appears that it might not be needed after all but in the meantime, having it in the TLB miss makes things a lot easier. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
Currently, the various forms of low level TLB invalidations are all implemented in misc_32.S for 32-bit processors, in a fairly scary mess of #ifdef's and with interesting duplication such as a whole bunch of code for FSL _tlbie and _tlbia which are no longer used. This moves things around such that _tlbie is now defined in hash_low_32.S and is only used by the 32-bit hash code, and all nohash CPUs use the various _tlbil_* forms that are now moved to a new file, tlb_nohash_low.S. I moved all the definitions for that stuff out of include/asm/tlbflush.h as they are really internal mm stuff, into mm/mmu_decl.h The code should have no functional changes. I kept some variants inline for trivial forms on things like 40x and 8xx. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
This commit moves the whole no-hash TLB handling out of line into a new tlb_nohash.c file, and implements some basic SMP support using IPIs and/or broadcast tlbivax instructions. Note that I'm using local invalidations for D->I cache coherency. At worst, if another processor is trying to execute the same and has the old entry in its TLB, it will just take a fault and re-do the TLB flush locally (it won't re-do the cache flush in any case). Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
We're soon running out of CPU features and I need to add some new ones for various MMU related bits, so this patch separates the MMU features from the CPU features. I moved over the 32-bit MMU related ones, added base features for MMU type families, but didn't move over any 64-bit only feature yet. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
This reworks the context management code used by 4xx,8xx and freescale BookE. It adds support for SMP by implementing a concept of stale context map to lazily flush the TLB on processors where a context may have been invalidated. This also contains the ground work for generalizing such lazy TLB flushing by just picking up a new PID and marking the old one stale. This will be implemented later. This is a first implementation that uses a global spinlock. Ideally, we should try to get at least the fast path (context ID already assigned) lockless or limited to a per context lock, but for now this will do. I tried to keep the UP case reasonably simple to avoid adding too much overhead to 8xx which does a lot of context stealing since it effectively has only 16 PIDs available. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
This splits the mmu_context handling between 32-bit hash based processors, 64-bit hash based processors and everybody else. This is preliminary work for adding SMP support for BookE processors. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
This adds supports to the "extended" DCR addressing via the indirect mfdcrx/mtdcrx instructions supported by some 4xx cores (440H6 and later). I enabled the feature for now only on AMCC 460 chips. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Nathan Lynch 提交于
We have more than one piece of code that looks up cache nodes manually using the "l2-cache" property. Add a common helper routine which does this and handles ePAPR's "next-level-cache" property as well as powermac. Signed-off-by: NNathan Lynch <ntl@pobox.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 16 12月, 2008 10 次提交
-
-
由 Benjamin Herrenschmidt 提交于
This adds a local_flush_tlb_mm() call as a pre-requisite for some SMP work for BookE processors. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
Instead of not defining it at all, this defines the macro as being empty, thus avoiding ifdef's in call sites when CONFIG_BUG is not set. Also removes an extra whitespace in the existing definition. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 FUJITA Tomonori 提交于
The block layer dropped the virtual merge feature (b8b3e16c). BIO_VMERGE_BOUNDARY definition is meaningless now (For POWER, BIO_VMERGE_BOUNDARY has been meaningless for a long time since POWER disables the virtual merge feature). Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp> Acked-by: NJens Axboe <jens.axboe@oracle.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Josh Boyer 提交于
Currently there are a number of platforms that open code access to the ppc_pci_flags global variable. However, that variable is not present if CONFIG_PCI is not set, which can lead to a build break. This introduces a number of accessor functions that are defined to be empty in the case of CONFIG_PCI being disabled. The various platform files in the kernel are updated to use these. Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Nathan Lynch 提交于
Since "Factor out cpu joining/unjoining the GIQ" (b4963255) the WARN_ON in xics_set_cpu_giq() is being triggered during boot on JS20 because the GIQ indicator is not available on that platform. While the warning is harmless and the system runs normally, it's nicer to check for the existence of the indicator before trying to manipulate it. Implement rtas_indicator_present(), which searches the /rtas/rtas-indicators property for the given indicator token, and use this function in xics_set_cpu_giq(). Also use a WARN statement in xics_set_cpu_giq to get better information on failure. Signed-off-by: NNathan Lynch <ntl@pobox.com> Acked-by: NMilton Miller <miltonm@bga.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Anton Vorontsov 提交于
The `have_of' variable is a relic from the arch/ppc time, it isn't useful nowadays. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Becky Bruce 提交于
Change #define stubs of dma_sync ops to be empty static inlines to avoid build warning. Signed-off-by: NBecky Bruce <beckyb@kernel.crashing.org> Acked-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Geert Uytterhoeven 提交于
commit 059e4938 ("powerpc/ps3: Add a sub-match id to ps3_system_bus") forgot to update the module alias support: - Add the sub-match ids to the module aliases, so udev can distinguish between different types of sub-devices. - Rename PS3_MODULE_ALIAS_GRAPHICS to PS3_MODULE_ALIAS_GPU_FB, as ps3fb binds to the "FB" sub-device. Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Geoff Levand 提交于
Fix a minor comment typo in pgtable-ppc64.h. Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
We were missing the CPU_FTR_NOEXECUTE bit in our cputable for all these processors. The result is that update_mmu_cache() would flush the cache for all pages mapped to userspace which is totally unnecessary on those processors since we already handle flushing on execute in the page fault path. This should provide a nice speed up ;-) Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
- 03 12月, 2008 9 次提交
-
-
由 Trent Piepho 提交于
The initial TLB mapping for the kernel boot didn't set the memory coherent attribute, MAS2[M], in SMP mode. If this code supported booting a secondary processor, which it doesn't yet, but if it did, then when a secondary processor boots, it would probably signal the primary processor by setting a variable called something like __secondary_hold_acknowledge. However, due to the lack of the M bit, the primary processor would not snoop the transaction (even if a transaction were broadcast). If primary CPU's L1 D-cache had a copy, it would not be flushed and the CPU would never see the ack. Which would have resulted in the primary CPU spinning for a long time, perhaps a full second before it gives up, while it would have waited for the ack from the secondary CPU that it wouldn't have been able to see because of the stale cache. The value of MAS2 for the boot page TLB1 entry is a compile time constant, so there is no need to calculate it in powerpc assembly language. Also, from the MPC8572 manual section 6.12.5.3, "Bits that represent offsets within a page are ignored and should be cleared." Existing code didn't clear them, this code does. The same when the page of KERNELBASE is found; we don't need to use asm to mask the lower 12 bits off. In the code that computes the address to rfi from, don't hard code the offset to 24 bytes, but have the assembler figure that out for us. Signed-off-by: NTrent Piepho <tpiepho@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Liu Yu 提交于
This patch add the handlers of SPE/EFP exceptions. The code is used to emulate float point arithmetic, when MSR(SPE) is enabled and receive EFP data interrupt or EFP round interrupt. This patch has no conflict with or dependence on FP math-emu. The code has been tested by TestFloat. Now the code doesn't support SPE/EFP instructions emulation (it won't be called when receive program interrupt), but it could be easily added. Signed-off-by: NLiu Yu <yu.liu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Liu Yu 提交于
Move to using the same macro definition for _FP_CHOOSENAN as s390, sh, sparc32/64. The original author didn't understand this and matched what sparc64 was doing and they have updated to this definition. Signed-off-by: NLiu Yu <yu.liu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Liu Yu 提交于
PowerPC float point division emulation is derived from gcc. I reported this problem on gcc maillist and got this reply: http://gcc.gnu.org/ml/gcc/2008-03/msg00543.html Since UDIV_NEEDS_NORMALIZATION is not used by kernel, we should use _FP_DIV_MEAT_1_udiv_norm to make sure the single float point is normalized before udiv_qrnnd. Signed-off-by: NLiu Yu <yu.liu@freescale.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-
由 Anton Vorontsov 提交于
The name of the device_node field differ across the platforms, so we have to implement inlined accessors. This is needed to avoid ugly #ifdef in the generic code. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NGrant Likely <grant.likely@secretlab.ca> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Becky Bruce 提交于
We need to swap these out once we start using swiotlb, so add them to dma_ops. Create CONFIG_PPC_NEED_DMA_SYNC_OPS Kconfig option; this is currently enabled automatically if we're CONFIG_NOT_COHERENT_CACHE. In the future, this will also be enabled for builds that need swiotlb. If PPC_NEED_DMA_SYNC_OPS is not defined, the dma_sync_*_for_* ops compile to nothing. Otherwise, they access the dma_ops pointers for the sync ops. This patch also changes dma_sync_single_range_* to actually sync the range - previously it was using a generous dma_sync_single. dma_sync_single_* is now implemented as a dma_sync_single_range with an offset of 0. Signed-off-by: NBecky Bruce <becky.bruce@freescale.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
Refactor the RCU based pte free code that was used on ppc64 to be used on all powerpc. Additionally refactor pte_free() & pte_free_kernel() into common code between ppc32 & ppc64. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Kumar Gala 提交于
The tlb invalidates in kmap_atomic/kunmap_atomic can be called from IRQ context, however they are only local invalidates (on the processor that the kmap was called on). In the future we want to use IPIs to do tlb invalidates this causes issue since flush_tlb_page() is considered a broadcast invalidate. Add local_flush_tlb_page() as a non-broadcast invalidate and use it in kmap_atomic() since we don't have enough information in the flush_tlb_page() call to determine its local. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Benjamin Herrenschmidt 提交于
The 32-bit hash code didn't need it so far so we don't update mm->cpu_vm_mask on context switch. This however will break when we merge the RCU based page table freeing patch and other upcoming 32-bit embedded SMP work, so this adds the update. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 01 12月, 2008 2 次提交
-
-
由 Christoph Hellwig 提交于
All architectures now use the generic compat_sys_ptrace, as should every new architecture that needs 32bit compat (if we'll ever get another). Remove the now superflous __ARCH_WANT_COMPAT_SYS_PTRACE define, and also kill a comment about __ARCH_SYS_PTRACE that was added after __ARCH_SYS_PTRACE was already gone. Signed-off-by: NChristoph Hellwig <hch@lst.de> Acked-by: NDavid S. Miller <davem@davemloft.net> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Al Viro 提交于
called only from __init, calls __init. Incidentally, it ought to be static in file. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 25 11月, 2008 1 次提交
-
-
由 Hollis Blanchard 提交于
When the VM exits, we must call put_page() for every page referenced in the shadow TLB. Without this patch, we usually leak 30-50 host pages (120 - 200 KiB with 4 KiB pages). The maximum number of pages leaked is the size of our shadow TLB, 64 pages. Signed-off-by: NHollis Blanchard <hollisb@us.ibm.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 19 11月, 2008 6 次提交
-
-
由 Milton Miller 提交于
With the new generic smp call function helpers, I noticed the code in smp_message_recv was a single function call in many cases. While getting the message number from the ipi data is easy, we can reduce the path length by a function and data-dependent switch by registering seperate IPI actions for these simple calls. Originally I left the ipi action array exposed, but then I realized the registration code should be common too. The three users each had their own name array, so I made a fourth to convert all users to use a common one. Signed-off-by: NMilton Miller <miltonm@bga.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Nick Piggin 提交于
This implements an optimised mutex fastpath for powerpc, making use of acquire and release barrier semantics. This takes the mutex lock+unlock benchmark from 203 to 173 cycles on a G5. Signed-off-by: NNick Piggin <npiggin@suse.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Nick Piggin 提交于
After commit 598056d5 ("[POWERPC] Fix rmb to order cacheable vs. noncacheable"), rmb() becomes a sync instruction, which is needed to order cacheable vs noncacheable loads. However smp_rmb() is #defined to rmb(), and smp_rmb() can be an lwsync. This restores smp_rmb() performance by using lwsync there and updates the comments. Signed-off-by: NNick Piggin <npiggin@suse.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Nick Piggin 提交于
Change 2d1b2027 ("powerpc: Fixup lwsync at runtime") removed __SUBARCH_HAS_LWSYNC, causing smp_wmb to revert back to eieio for all CPUs. This restores the behaviour intorduced in 74f06095 ("powerpc: Optimise smp_wmb on 64-bit processors"). Signed-off-by: NNick Piggin <npiggin@suse.de> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Paul Mackerras 提交于
We have several instances of inline assembly code that use the addic or addic. instructions, but don't include XER in the list of clobbers. The addic and addic. instructions affect the carry bit, which is in the XER register. This adds "xer" to the list of clobbers for those inline asm statements that use addic or addic. and didn't already have it. Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
由 Geert Uytterhoeven 提交于
Introduce ps3_gpu_mutex to synchronizes GPU-related operations, like: - invoking the L1GPU_CONTEXT_ATTRIBUTE_FB_BLIT command using the lv1_gpu_context_attribute() hypervisor call, - handling the PS3AV_CID_AVB_PARAM packet in the PS3 A/V Settings driver. Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com> Signed-off-by: NGeoff Levand <geoffrey.levand@am.sony.com> Signed-off-by: NPaul Mackerras <paulus@samba.org>
-
- 09 11月, 2008 1 次提交
-
-
由 Li Yang 提交于
Fixes following build error: CC drivers/usb/gadget/fsl_qe_udc.o drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_stall_change': drivers/usb/gadget/fsl_qe_udc.c:156: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c:163: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eptx_stall_change': drivers/usb/gadget/fsl_qe_udc.c:173: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c:180: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_nack': drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c:201: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_eprx_normal': drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c:218: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_reset': drivers/usb/gadget/fsl_qe_udc.c:325: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c:342: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'qe_ep_register_init': drivers/usb/gadget/fsl_qe_udc.c:515: error: 'struct usb_ctlr' has no member named 'usb_usep' drivers/usb/gadget/fsl_qe_udc.c: In function 'ch9getstatus': drivers/usb/gadget/fsl_qe_udc.c:1981: error: 'struct usb_ctlr' has no member named 'usb_usep' make[2]: *** [drivers/usb/gadget/fsl_qe_udc.o] Error 1 Signed-off-by: NLi Yang <leoli@freescale.com> Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
-