Implemented .set_bdaddr handler provided by bluetooth stack for
Marvell devices for public address configuration.
A reboot restores the bdaddr to its original address.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for the QCA6174 chip.

    T:  Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 30 Spd=12  MxCh= 0
    D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
    P:  Vendor=13d3 ProdID=3432 Rev=00.02
    C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
    I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
    I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAnantha Krishnan <ananthk@codeaurora.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Instead of setting data->isoc manually, use BTUSB_BROKEN_ISOC to
indicate that isochronous endpoints are not needed for CSR USB
sniffer devices.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The isochronous endpoints are not valid when the Intel Bluetooth
controller boots up in bootloader mode. So just mark these endpoints
as broken and then they will not be configured.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The interrupt interface for the Intel USB bootloader devices is only
enabled after receiving SetInterface(0, AltSetting=0). When this USB
command is not send, then no HCI events will be received.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The module parameters to ignore devices based on USB VID/PID are not
needed at all. So just remove them.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Intel Bluetooth devices that boot up in bootloader mode can not
be used as generic HCI devices, but their HCI transport is still
valuable and so bring that up as raw-only devices.

T:  Bus=02 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 14 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0a5a Rev= 0.00
S:  Manufacturer=Intel(R) Corporation
S:  Product=Intel(R) Wilkins Peak 2x2
S:  SerialNumber=001122334455 WP_A0
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When the Broadcom USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When the Intel USB controller has a default address, then set the quirk
so the Bluetooth core knows that controller configuration is required.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The Broadcom BCM20702A0 USB controllers might come with the default
address 00:20:70:02:A0:00 when booting up. If this happens, then warn
about such address being used.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Some Intel Bluetooth controllers come with a default address. If this
address is found, print an error to warn the user about it.

The controller is fully operational, but the danger of duplicate
Bluetooth addresses might causes issues. At least with a clear
error it becomes easier to debug these cases.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For the Intel based USB devices add support for configuration of
the public device address.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

For the Broadcom based USB devices add support for configuration of
the public device address.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This reverts commit ca58e594.

For some unclear reason this patch tries to add suport for the
product ID 0xe005, but it ends up adding product ID 0x3005 to
all the tables. This is obviously wrong and causing multiple
issues.

The original patch seemed to be fine, but what ended up in 3.15
is not what the patch intended. The commit 0a3658cc is
already present and adds support for this hardware. This means
only revert of this broken commit is requird.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Reported-by: NAlexander Holler <holler@ahsoftware.de>
Cc: stable@vger.kernel.org # 3.15.x

After hardware reset, some BCM Bluetooth adapters obtain their initial firmware
from OTPROM chip. Once this initial firmware is running, the firmware can be
further upgraded over HCI interface with .hcd files provided by Broadcom. This
is also known as "patch RAM" support. This change implements that.

If the .hcd file is not found in /lib/firmware, BCM Bluetooth adapter continues
to operate with the initial firmware. Sample kernel log:
  hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
  Bluetooth: hci0: BCM: patch brcm/BCM20702A0-0a5c-22be.hcd not found

If the .hcd file is found, btusb driver pushes it to the BCM Bluetooth adapter and
it starts using the new firmware. Sample kernel log:
  hotplug: sys=firmware act=add fw=brcm/BCM20702A0-0a5c-22be.hcd dev=...
  Bluetooth: hci0: BCM: patching hci_ver=06 hci_rev=1000 lmp_ver=06 lmp_subver=220e
  Bluetooth: hci0: BCM: firmware hci_ver=06 hci_rev=1389 lmp_ver=06 lmp_subver=220e

Above, we can see that hci_rev goes from 1000 to 1389 as a result of the upgrade.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for the AR9462 chip

T:  Bus=01 Lev=01 Prnt=01 Port=03 Cnt=03 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=3007 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NMohammed Habibulla <moch@chromium.org>
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This reverts commit d2bee8fb.

Enabling autosuspend for Intel Bluetooth devices has been shown to not
work reliable. It does work for some people with certain combinations
of USB host controllers, but for others it puts the device to sleep and
it will not wake up for any event.

These events can be important ones like HCI Inquiry Complete or HCI
Connection Request. The events will arrive as soon as you poke the
device with a new command, but that is not something we can do in
these cases.

Initially there were patches to the xHCI USB controller that fixed
this for some people, but not for all. This could be well a problem
somewhere in the USB subsystem or in the USB host controllers or
just plain a hardware issue somewhere. At this moment we just do
not know and the only safe action is to revert this patch.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Cc: Tedd Ho-Jeong An <tedd.an@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

usb devices info:

T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 13 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NPeng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The device found on Asus Z87 Expert motherboard requires firmware to work
correctly.

T:  Bus=03 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17d0 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This will help to manage table of supported IDs.

There is no functional change.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Add support for IMC Networks (Broadcom based) to btusb driver.

Below the output of /sys/kernel/debug/usb/devices for this device:

T:  Bus=01 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3404 Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=240A649F8246
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NJurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The device is not functional without firmware.

The device without firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  3 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311f Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

The device with firmware:
T:  Bus=02 Lev=02 Prnt=02 Port=05 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3007 Rev=00.01
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The device will bind to btusb without firmware, but with the original
buggy firmware device discovery does not work. No devices are detected.

Device descriptor without firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms

with firmware:
T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  3 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=311e Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There exists a set of Bluetooth USB devices that show up on the USB
bus as 0a12:0001 and identify themselves as devices from CSR. However
they are not. When sending Read Local Version command they now have
a split personality and say they are from Broadcom.

  < HCI Command: Read Local Version Information (0x04|0x0001) plen 0
  > HCI Event: Command Complete (0x0e) plen 12
      Read Local Version Information (0x04|0x0001) ncmd 1
      status 0x00
      HCI Version: 2.0 (0x3) HCI Revision: 0x3000
      LMP Version: 2.0 (0x3) LMP Subversion: 0x420b
      Manufacturer: Broadcom Corporation (15)

The assumption is that they are neither CSR nor Broadcom based devices
and that they are designed and manufactured by someone else.

For the most parts they follow the Bluetooth HCI specification and
can be used as standard Bluetooth devices. However they have the
minor problem that the Delete Stored Link Key command is not working
as it should.

During the Bluetooth controller setup, this command is needed if
stored link keys are supported. For these devices it has to be
assumed that this is broken and so just set a quirk to clearly
indicate the behavior. After that the setup can just proceed.

Now the trick part is to detect these faulty devices since we do
not want to punish all CSR and all Broadcom devices. The original
devices do actually work according to the specification.

What is known so far is that these broken devices set the USB bcdDevice
revision information to 1.0 or less.

T:  Bus=02 Lev=01 Prnt=01 Port=08 Cnt=03 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a12 ProdID=0001 Rev= 1.00
S:  Manufacturer=Bluetooth v2.0
S:  Product=Bluetooth V2.0 Dongle

T:  Bus=05 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0a12 ProdID=0001 Rev= 0.07

In case of CSR devices, the bcdDevice revision contains the firmware
build ID and that is normally a higher value. If the bcdDevice revision
is 1.0 or less, then an extra setup stage is checking if Read Local
Version returns CSR manufacturer information. If not then it will be
assumed that this is a broken device and the Delete Stored Link Key
command will be marked as broken.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch adds support for new Toshiba Bluetooth device.

T:  Bus=05 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0930 ProdID=0220 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NMarco Piazza <mpiazza@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

This patch enables autosuspend for Intel Bluetooth device.

After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.

"The USB specification states that all USB devices must support power
management.  Nevertheless, the sad fact is that many devices do not
support it very well.  You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely.  This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.

For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs.  Hubs, at least, appear to be reasonably well-behaved in
this regard."

This document also described how the driver can enables the autosuspend
by using an USB api.

"Drivers can enable autosuspend for their devices by calling

	usb_enable_autosuspend(struct usb_device *udev);

in their probe() routine, if they know that the device is capable of
suspending and resuming correctly.  This is exactly equivalent to
writing "auto" to the device's power/control attribute."

For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for new Intel Bluetooth device.

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0a2a Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

T:  Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e05f Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: NJoshua Richenhagen <richenhagen@gmail.com>
Signed-off-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=300b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: NFace <falazemi@gmail.com>
Signed-off-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The btusb_table[] and blacklist_table[] USB device tables can be
declared as const.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Instead of masking hdev inside the skb->dev parameter, hand it
directly to the driver as a parameter to hdev->send. This makes
the driver interface more clear and simpler.

This patch fixes all drivers to accept and handle the new parameter
of hdev->send callback. Special care has been taken for bpa10x
and btusb drivers that require having skb->dev set to hdev for
the URB transmit complete handlers.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

When changing the alternate setting for the ISOC endpoints, use the
hci_conn_num() helper function to count currently established SCO
and eSCO connections and store the the value. This avoids direct
access to the connection hash.

In addition use the stored value instead accessing the connection
hash over and over again.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Many btusb devices have 2 modes, a hid mode and a bluetooth hci mode. These
devices default to hid mode for BIOS use. This means that after having been
reset they will revert to HID mode, and are no longer usable as a HCI.

Therefor it is a very bad idea to just blindly make reset_resume point to
the regular resume handler. Note that the btusb driver has no clue how to
switch these devices from hid to hci mode, this is done in userspace through
udev rules, so the proper way to deal with this is to not have a reset-resume
handler and instead let the usb-system re-enumerate the device, and re-run
the udev rules.

I must also note, that the commit message for the commit causing this
problem has a very weak motivation for the change:

"Add missing reset_resume dev_pm_ops. Missing reset_resume results in the
following message after power management device test. This change sets
reset_resume to btusb_resume().

[ 2506.936134] btusb 1-1.5:1.0: no reset_resume for driver btusb?
[ 2506.936137] btusb 1-1.5:1.1: no reset_resume for driver btusb?"

Making a change solely to silence a warning while also changing important
behavior (normal resume handling versus re-enumeration) requires a commit
message with a proper explanation why it is safe to do so, which clearly lacks
here, and unsurprisingly it turns out to not be safe to make this change.

Reverting the commit in question fixes bt no longer working on my Dell
E6430 after a suspend/resume, and I believe it likely also fixes the
following bugs:
https://bugzilla.redhat.com/show_bug.cgi?id=988481
https://bugzilla.redhat.com/show_bug.cgi?id=1010649
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1213239

This reverts commit 502f7696.

Cc: Shuah Khan <shuah.kh@samsung.com>
Cc: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add generic rule on encountering Belkin bluetooth usb device F8065bf.

Relevant section from /sys/kernel/debug/usb/devices:

T:  Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=050d ProdID=065a Rev= 1.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=0002723E2D29
C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
Signed-off-by: NKen O'Brien <kernel@kenobrien.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Yet another vendor specific ID for this chipset; this one for the ASUS
USB-BT400 Bluetooth 4.0 adapter.

T:  Bus=03 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0b05 ProdID=17cb Rev=01.12
S:  Manufacturer=Broadcom Corp
S:  Product=BCM20702A0
S:  SerialNumber=000272C64400
C:  #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=(none)
I:  If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I:  If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)

Cc: stable@vger.kernel.org
Signed-off-by: NRaphael Kubo da Costa <rakuco@FreeBSD.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

usb device info:

T:  Bus=06 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 15 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e005 Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NPeng Chen <pengchen@qca.qualcomm.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add support for the AR9462 chip

T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e003 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

Add support for the AR3012 chip.

T:  Bus=03 Lev=01 Prnt=01 Port=06 Cnt=01 Dev#=  6 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=3121 Rev=00.02
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

T:  Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#=  5 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3402 Rev= 0.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

Bug: https://bugzilla.kernel.org/show_bug.cgi?id=59701Signed-off-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>

PTR_ERR() returns a signed long type value which is limited by IS_ERR(),
it must be a negative number whose range is [-MAX_ERRNO, 0).

The bug here returns negative numbers as error codes, then check it by
"if (ret < 0)", but -PTR_ERR() is actually positive. The wrong use here
leads to failure as below, even panic.

[   12.958920] Bluetooth: hci0 command 0xfc8e tx timeout
[   14.961765] Bluetooth: hci0 command 0xfc8e tx timeout
[   16.964688] Bluetooth: hci0 command 0xfc8e tx timeout
[   20.954501] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   22.957358] Bluetooth: hci0 command 0xfc8e tx timeout
[   30.948922] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   32.951780] Bluetooth: hci0 command 0xfc8e tx timeout
[   40.943359] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   42.946219] Bluetooth: hci0 command 0xfc8e tx timeout
[   50.937812] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   52.940670] Bluetooth: hci0 command 0xfc8e tx timeout
[   60.932236] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   62.935092] Bluetooth: hci0 command 0xfc8e tx timeout
[   70.926688] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   72.929545] Bluetooth: hci0 command 0xfc8e tx timeout
[   80.921111] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-110)
[   82.923969] Bluetooth: hci0 command 0xfc2f tx timeout
[   90.915542] Bluetooth: hci0 sending Intel patch command (0xfc2f) failed (-110)
[   92.918406] Bluetooth: hci0 command 0xfc11 tx timeout
[  100.909955] Bluetooth: hci0 sending Intel patch command (0xfc11) failed (-110)
[  102.912858] Bluetooth: hci0 command 0xfc60 tx timeout
[  110.904394] Bluetooth: hci0 sending Intel patch command (0xfc60) failed (-110)
[  112.907293] Bluetooth: hci0 command 0xfc11 tx timeout
[  120.898831] Bluetooth: hci0 exiting Intel manufacturer mode failed (-110)
[  120.904757] bluetoothd[1030]: segfault at 4 ip 00007f8b2eb55236 sp 00007fff53ff6920 error 4 in bluetoothd[7f8b2eaff000+cb000]
Signed-off-by: NAdam Lee <adam.lee@canonical.com>
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>