Defining a function with no parameters as 'T foo()' is the deprecated
K&R style, and is not strictly equivalent to defining it as 'T foo(void)'.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro spin_event_timeout() was designed for simple polling of hardware
registers with a timeout, so use it when we poll the MIIMIND register.
This allows us to return an error code instead of polling indefinitely.

Note that PHY_INIT_TIMEOUT is a count of loop iterations, so we can't use
it for spin_event_timeout(), which asks for microseconds.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inspired by implementation in smsc911x.c and smsc9420.c
Tested on ARM/pandaboard running android
Signed-off-by: NEmeric Vigier <emeric.vigier@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

as the manual of module_pci_driver says that
it can be used when the init and exit functions of
the module does nothing but the pci_register_driver
and pci_unregister_driver.

use it for rdc's r6040 driver, as the init and exit
paths does as above, and also this reduces a little
amount of code.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

l4_rxhash is set on skb when rxhash is obtained from canonical 4-tuple
over transport ports/addresses.

We can set skb->l4_rxhash for all incoming TCP packets on bnx2x for
free, as cqe status contains a hash type information.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8111G, the settings of phy and firmware are replaced with
ocp functions. r8168g_mdio_{write / read} redirects the relative
settings to suitable ocp functions. A per-device variable is needed
to evaluate the real address of ocp functions.
rtl_writephy(tp, 0x1f, xxxx) is dedicated to keeping said variable
up-to-date.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

Twelve functions can fail silently. Now they have a chance to complain.

Macro and pasting abuse has been kept at a level where tags and
friends should not be hurt.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Further changes need more context down in the call stack.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>

ETH_P_IP is host Endian, skb->protocol is big Endian, when
compare them, we should change ETH_P_IP from host endian
to big endian, htons, not ntohs.

CC: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

broadcom, not marvell.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NDavid Daney <david.daney@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If registering of one of them fails, all already registered drivers
of this module will be unregistered.

Use the new register/unregister functions in all drivers
registering more than one driver.

amd.c, realtek.c: Simplify: directly return registration result.

Tested with broadcom.c
All others compile-tested.
Signed-off-by: NChristian Hohnstaedt <chohnstaedt@innominate.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bcm87xx phys don't support autonegotiation, so don't use it by
default, as otherwise phy_state_machine() will try to enable it (using
c22 requests, which also don't make any sense for the bcm78xx).
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-enable interrupts if it is not our interrupt
Signed-off-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Optima EEE chipset.
Signed-off-by: NMirko Lindner <mlindner@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

OFF carrier state is setup in probe() open() and suspend() functions.
The carrier ON state is managed in macb_handle_link_change().
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DRV_MODULE_VERSION here is "2.7.2.2" which is only 8 chars but we copy
12 bytes from the stack so it's a small information leak.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed excess calls to skb_copy_expand() or memmove() in asix driver.

This driver needs to push 4 bytes in front of frame (packet_len)
and maybe add 4 bytes after the end (if padlen is 4)

So it should set needed_headroom & needed_tailroom to avoid
copies. But its not enough, because many packets are cloned
before entering asix_tx_fixup() and this driver use skb_cloned()
as a lazy way to check if it can push and put additional bytes in frame.

Avoid skb_copy_expand() expensive call, using following rules :

- We are allowed to push 4 bytes in headroom if skb_header_cloned()
  is false (and if we have 4 bytes of headroom)

- We are allowed to put 4 bytes at tail if skb_cloned()
  is false (and if we have 4 bytes of tailroom)

TCP packets for example are cloned, but skb_header_release()
was called in tcp stack, allowing us to use headroom for our needs.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Allan Chou <allan@asix.com.tw>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: Ming Lei <tom.leiming@gmail.com>
Tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The drop action is implemented by allocating a QP and keeping it in a reset state
such that the HW drops any packets which are steered to that QP. When a drop action
is requested, we attach the relevant flow to that QP.
Sign-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the ethtool APIs for attaching L2/L3/L4 based flow steering
rules to the netdevice RX rings. Added set_rxnfc callback and enhanced
the existing get_rxnfc callback.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device managed flow steering API has three promiscuous modes:

1. Uplink - captures all the packets that arrive to the port.
2. Allmulti - captures all multicast packets arriving to the port.
3. Function port - for future use, this mode is not implemented yet.

Use these modes with the flow_attach and flow_detach firmware commands
according to the promiscuous state of the netdevice.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with other device resources, the resource tracker is needed for supporting
device managed flow steering rules under SRIOV: make sure virtual functions
delete only rules created by them, and clean all rules attached by a crashed VF.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is modified to support three operation modes.

If supported by firmware use the device managed flow steering
API, that which we call device managed steering mode. Else, if
the firmware supports the B0 steering mode use it, and finally,
if none of the above, use the A0 steering mode.

When the steering mode is device managed, the code is modified
such that L2 based rules set by the mlx4_en driver for Ethernet
unicast and multicast, and the IB stack multicast attach calls
done through the mlx4_ib driver are all routed to use the device
managed API.

When attaching rule using device managed flow steering API,
the firmware returns a 64 bit registration id, which is to be
provided during detach.

Currently the firmware is always programmed during HCA initialization
to use standard L2 hashing. Future work should be done to allow
configuring the flow-steering hash function with common, non
proprietary means.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for firmware commands to attach/detach a new device managed
steering mode. Such network steering rules allow the user to provide an
L2/L3/L4 flow specification to the firmware and have the device to steer
traffic that matches that specification to the provided QP.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of checking the firmware supported steering mode in various
places in the code, add a dedicated field in the mlx4 device capabilities
structure which is written once during the initialization flow and read
across the code.

This also set the grounds for add new steering modes. Currently two modes
are supported, and are named after the ConnectX HW versions A0 and B0.

A0 steering uses mac_index, vlan_index and priority to steer traffic
into pre-defined range of QPs.

B0 steering uses Ethernet L2 hashing rules and is enabled only
if the firmware supports both unicast and multicast B0 steering,

The current steering modes are relevant for Ethernet traffic only,
such that Infiniband steering remains untouched.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, for every change in the net device multicast list, the driver
detaches all the addresses from the HW device, and then attaches the
updated list. This behavior is wrong from two aspects: first, it causes
a load of firmware commands and second, there is period of time where
the correct addresses are not attached, which turned into packet loss.

To improve - a copy of the multicast list is saved by the driver. For
every change in the multicast list, the multicast list copy is used
to find the delta between those two lists and add or remove multicast
addresses as needed.
Reported-by: NShawn Bohrer <sbohrer@rgmadvisors.com>
Cc: Shawn Bohrer <sbohrer@rgmadvisors.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the IDs used by the resource tracker are of type u32, so far this was
ok since all the different resources we were tracking could be encoded in 32bit.

As a preparation step for tracking of resources whose IDs need > 32 bits such
as network flow steering rules, who are 64 bit in size, move to use 64 bit
based resource IDs.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the data structure used for managing the SRIOV resource tracking
mechanism from radix tree to red-black tree. This is preparation step
for supporting resource IDs which are 64bit long, such as network flow
steering rules. Such IDs can't be used as radix-tree keys on 32bit
architectures and hence the reason for the change.
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.co.il>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pci_set_drvdata is called twice at the remove path of driver,
call it once.
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Otherwise local_bh_enable() complains.
Reported-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove excessive variable used for the return status.
Signed-off-by: NAlexander Smirnov <alex.bluesman.smirnov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Jon Mason <mason@myri.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>

Cc: Divy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>