Implement arch specific arch_get_memory_phys_device function and
initialize phys_device for each memory section.  That way we finally can
tell which piece of memory belongs to which physical device.

This makes s390's /sys/devices/system/memory/memoryX/phys_device display
the correct thing?
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Deactivate inbound checksumming on HiperSocket is a valid but
dangerous optimization in case the frame is routed from an OSA
network to an HiperSockets network. To go for sure we change the
default to software checksumming.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Depending on their definition in z/VM, virtual devices for z/VM
VSWITCH or GuestLAN must be configured either in layer2 or in
layer3 mode. If qeth detects a layer mismatch, device activation
fails. Trying to recover from this error cannot help; thus
scheduling a recovery should be avoided.
In addition, since recovery is forbidden during online setting of
a qeth device, existence of its network device is guaranteed for all
dev_close() calls in qeth. The corresponding checks can be removed.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If HiperSockets Network Traffic Analyzer is switched off, but trace
disabling fails somehow, the qeth driver does not switch off its
promisc mode status. A following sniffer reactivation fails, since
qeth does not see a need to reenable tracing.
At the same time the code analyzing results of trace commands is
restructured.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dhcp frames are valid IPv4 packets so there is no need to send them
in pass thru mode. This allows dhcp packets to pass HiperSockets.
Also the dhcp release frame is send out correctly with this patch.
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

provide qeth kmsg definitions to enable hash string generation for
kernel message created with dev_err().
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NFrank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The smsgiucv_app driver registers a callback with the smsgiucv driver
to receive z/VM CP special messages (SMSG) starting with "APP".

When the callback is called for special messages, the driver creates
an uevent for the received message.  The uevent consists of additional
environment data containing the message prefix ("APP"), message sender,
and message content.

udev rules can be used to trigger application specific actions through
matching the content or sender of the special message.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Declare the smsgiucv prefix char pointer as "const" and use
use const char pointers in callback functions.
Signed-off-by: NHendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

In z/VM it is possible to attach a device as read-only. To prevent
unintentional write requests and subsequent I/O errors, we can detect
this configuration using the z/VM DIAG 210 interface and set the
respective linux block device to read-only as well.
Signed-off-by: NStefan Weinhuber <wein@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

zfcp and qeth are setting flags for the qdio-layer, but these flags
are not used in qdio. Patch removes the flag definitions from qdio
and their settings in zfcp and qeth.

Cc: Jan Glauber <jang@linux.vnet.ibm.com>
Cc: Christof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add a missing bracket to only log the outbound handler event in the
appropriate case.
Signed-off-by: NUrsula Braun <ursula.braun@de.ibm.com>
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

After we try to steal a lock on a ccw device in boxed state,
we have to restart device recognition and potentially reprobing.

In this case ccw_device_init_count was erroneously decreased
twice. This patch fixes the issue.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove the PSF order/suborder check from the Symmetrix CKD dasd ioctl.
In exchange restrict the ioctl to CAP_SYS_ADMIN and CAP_SYS_RAWIO.
Signed-off-by: NNigel Hislop <hislop_nigel@emc.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

With this patch the prefix registers of all online CPUs are stored in the
the zcore dump header. This allows dump analysis tools to access the register
information that is stored in the prefix pages without using the System.map.
Signed-off-by: NMichael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Flushing the dasd ccw request queue may stop the processing of the
block device request queue. Destroy partitions may wait for
outstanding requests and thus hang.
Swapping dasd_destroy_partitions and dasd_flush_request_queue so that
the request queue is empty before dasd_destroy_partitions is called.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

The function dasd_device_from_cdev returns a reference to the dasd
device and increases the refcount by one. If an exception occurs,
the refcount was not decreased in all cases
e.g. in dasd_discipline_show.
Prevent the offline processing from hang by correcting two functions
to decrease the refcount even if an error occured.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Setting a DASD online and offline in quick succession may cause
a kernel panic or let the chhccwdev command wait forever.
The Online process is split into two parts. After the first part
is finished the offline process may be called. This may result
in a situation where the second online processing part tries to
set the DASD offline as well.
Use a mutex to protect online and offline against each other.
Also correct some checking.
Signed-off-by: NStefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Use asm offsets to make sure the offset defines to struct _lowcore and
its layout don't get out of sync.
Also add a BUILD_BUG_ON() which checks that the size of the structure
is sane.
And while being at it change those sites which use odd casts to access
the current lowcore. These should use S390_lowcore instead.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Introduce the MACHINE_IS_LPAR flag for code that should only be
executed if Linux is running in an LPAR.
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove a memset hack that relied on the internal layout of the
qdio_irq struct and move the per device statistics data into an own
cache line to avoid cache line bashing between the inbound and the
outbound queue tasklets. Also reduce the number of allocated queues
from 32 to 4 which is the current maximum. That saves a cache line
in struct qdio_irq.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Add counters for the number of processed SBALs. The numbers summarize
how many SBALs were processed at each queue scan and indicate the
utilization of the queue. Furthermore the number of unsuccessfull
queue scans, SBAL errors and the total number of processed
SBALs are accounted.

Also regroup struct qdio_q to move read-mostly and write-mostly data
into different cachelines.
Signed-off-by: NJan Glauber <jang@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Remove support to be able to dump 31 bit systems with a 64 bit dumper.
This is mostly useless since no distro ships 31 bit kernels together
with a 64 bit dumper.
We also get rid of a bit of hacky code.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Some parts of cio do not shift PAGE_DEFAULT_KEY correctly and end up
with an incorrect key in their data structures.
Since the default key is zero this doesn't really matter. However if
somebody would use key-controlled protection for debugging purposes
it would be quite helpful if all of this would work as expected.

Also remove a stale declaration.
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

ccw_device_pm_restore: trigger subchannel event to better handle
changes to the subchannel device.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Callers of ccw_device_notify could not distinguish between a driver
who has no notifier registered and a driver who doesn't want to keep
a device after a certain event. Change this by adding proper return
codes.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Make the potentially long blocking wait_event's used by the cio
settle mechanism interruptible.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

To fetch a pending channel report word (crw) we use a kernel
thread which triggers stcrw and sleeps on a semaphore. The s390
machine check handler uses crw_handle_channel_report to handle
one crw if needed.

This patch replaces the semaphore with a waitqueue (to block the
kernel thread) and an atomic_t (to count the number of pending
requests).

By this we achieve the ability to force this thread to check for
a pending crw (independent on when it is triggered by the machine
check handler) and wait for this action to finish.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

This patch introduces a proc file cio_settle. A write request to
this file is blocked until all queued cio actions are handled.

This will allow userspace to wait for pending work affecting
device availability after changing cio_ignore or the hardware
configuration.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

We used to maintain 2 singlethreaded workqueues for synchronization
and to trigger work from interrupt context. Since our latest cio
changes we only use one of these workqueues. So get rid of the
unused workqueue, rename the remaining one to "cio_work_q" and move
its ownership to the channel subsystem driver.
Signed-off-by: NSebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Except for SCSI no device drivers distinguish between physical and
hardware segment limits.  Consolidate the two into a single segment
limit.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

The block layer calling convention is blk_queue_<limit name>.
blk_queue_max_sectors predates this practice, leading to some confusion.
Rename the function to appropriately reflect that its intended use is to
set max_hw_sectors.

Also introduce a temporary wrapper for backwards compability.  This can
be removed after the merge window is closed.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

Move the qdio related structs and some helper functions to a new
zfcp_qdio.h header file. While doing this, rename the struct
zfcp_queue_req to zfcp_qdio_req to adhere to the naming scheme used in
zfcp. This allows a better seperation of the qdio code and inlining
the helper functions will save some function calls.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The FC4 types are already available from exchange port.  Use this for
reporting the FC4 types, instead of having the value hardcoded in
zfcp.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Move the decision which trace tag and trace level to use for the scsi
result trace to zfcp_dbf.h. zfcp_dbf_scsi_result is already an inline
function, so move the trace code there, simplifying the response
handling in zfcp_fsf.c.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Kernel code uses dev as short name for the struct device. Rename the
sysfs_device in zfcp_unit and zfcp_port to match this convention.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

zfcp_fsf_req_create assigns the same value twice to req_seq_no.
Remove one assignment and move the req_id and seq_no assignments to
one place.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

0 is a valid value for a LUN. It is slightly confusing to also see 0
in the trace entries relating to adapter and port. Change this to use
0xFFFFFFFFFFFFFFFF in the LUN field when the trace entry does not
relate to a LUN or unit.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The smatch tool from http://repo.or.cz/w/smatch.git warns about this:

drivers/s390/scsi/zfcp_scsi.c +64 zfcp_scsi_command_fail(5) warn: variable dereferenced before check 'scpnt->device'
drivers/s390/scsi/zfcp_scsi.c +64 zfcp_scsi_command_fail(5) warn: variable dereferenced before check 'scpnt->device->host'
drivers/s390/scsi/zfcp_scsi.c +93 zfcp_scsi_queuecommand(23) warn: variable dereferenced before check 'unit'

Fix the first two warnings by removing the checks for scpnt->device
and -> host: As long as the SCSI command exists, there is also a
scsi_device and a Scsi_Host.

Fix the last warning by removing the BUG_ON checks in
zfcp_scsi_queuecommand, they are leftovers from previous paranoia
about wrong pointers between data structures.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Remove the unused payload field from the struct zfcp_dbf_san_record,
saving some space in the SAN trace.
Reviewed-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>