On OMAP4 SDP the audio setup includes the twl6040 codec and digital
microphones.

Since OMAP4 SDP is a reference board it has all possible audio interfaces
connected. This information is passed via the ti,audio-routing
property.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The twl6040 provides the audio and vibra support on OMAP4 SDP boards.
It is connected to i2c1 bus with 0x4b address.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

There are devices connected to VBAT.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patches fixes some status = "disable" strings to "disabled", the correct
way of disabling nodes in the devicetree.

Just the OMAP part here, the rest goes via other patches and trees.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Acked-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.

[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

Add the debug LEDs nodes for an OMAP4 SDP/Blaze.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add OMAP mmc related device tree data for OMAP4.
Currenly limited to only omap4-panda and omap4-sdp
boards.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>

Add an ethernet SPI chip in the OMAP4 SDP/Blaze board DTS file.

Add a fixed regulator node controlled by a GPIO line to supply
the ethernet chip.

Based on original code from Rajendra.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Update DTS file with required clock frequencies
for the i2c client devices existing on sdp4430.

Add the twl6030 node inside the i2c1 controller node.
This is the minimal support needed to boot OMAP4 boards
without any crash.
The support for all the features included in this MFD will be
added later.

Add the RTC submodule inside the twl node.

Add tmp105 temperature sensor in i2c3
Add bh1780 Ambient Light Sensor in i2c3
Add hmc5843 3-Axis Digital Compass in i2c4
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>

Since 3.2, the CONFIG_ARM_ATAG_DTB_COMPAT config allows
an old bootloader to still use ATAG to provide cmdline.

Remove chosen/bootargs from the DTS board files.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add the SDP/Blaze (Software Development Board) support with
device tree.
That file is based on the omap4-panda.dts.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>

Based on the original omap4-panda.dts file from Manju.
http://www.spinics.net/lists/linux-omap/msg55836.html

Add memory information and a default bootargs to allow
a boot from RAMDISK.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>