Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 161
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 07 7月, 2015 13 次提交
  3. 03 7月, 2015 4 次提交
  5. 23 6月, 2015 3 次提交
  7. 22 6月, 2015 7 次提交
  9. 21 6月, 2015 3 次提交
    • T
      clk: samsung: exynos4: add cpu clock configuration data and instantiate cpu clock · 6ae5a0b4
      由 Thomas Abraham 提交于 
      With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4210.

Changes by Bartlomiej:
- fixed issue with wrong dividers being setup by Common Clock Framework
  (by an addition of CLK_RECALC_NEW_RATES clock flag to mout_apll clock,
  without this change cpufreq-dt driver showed ~10 mA larger energy
  consumption when compared to cpufreq-exynos one when "performance"
  cpufreq governor was used on Exynos4210 SoC based Origen board), this
  was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE
  and CLK_DIVIDER_READ_ONLY clock flags in the original patchset (in
  "[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update
  clock flags") but using these flags is not sufficient to fix the issue
  observed
- removed Exynos5250 and Exynos5420 support for now

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>
      6ae5a0b4
    • T
      clk: samsung: add infrastructure to register cpu clocks · ddeac8d9
      由 Thomas Abraham 提交于 
      The CPU clock provider supplies the clock to the CPU clock domain. The
composition and organization of the CPU clock provider could vary among
Exynos SoCs. A CPU clock provider can be composed of clock mux, dividers
and gates. This patch defines a new clock type for CPU clock provider and
adds infrastructure to register the CPU clock providers for Samsung
platforms.

Changes by Bartlomiej:
- fixed issue with setting lower dividers before the parent clock speed
  was lowered (the issue resulted in lockup on Exynos4210 SoC based
  Origen board when "ondemand" cpufreq governor was stress tested)
- fixed missing spin_unlock on error in exynos_cpuclk_post_rate_change()
  problem by moving cfg_data search outside of the spin locked area
- removed leftover kfree() in exynos_register_cpu_clock() that could
  result in dereferencing the NULL pointer on error
- moved spin_lock earlier in exynos_cpuclk_pre_rate_change() to cover
  reading of E4210_SRC_CPU and E4210_DIV_CPU1 registers
- added missing "last chance" checks to wait_until_divider_stable() and
  wait_until_mux_stable() (needed in case that IRQ handling took long
  time to proceed and resulted in function printing incorrect error
  message about timeout)
- moved E4210_CPU_DIV[0,1]() macros just before their only users,
  this resulted in moving them from patch #2 to patch #3/6 ("clk:
  samsung: exynos4: add cpu clock configuration data and instantiate
  cpu clock")
- removed E5250_CPU_DIV[0,1](), E5420_EGL_DIV0() and E5420_KFC_DIV()
  macros for now
- added my Copyrights to drivers/clk/samsung/clk-cpu.c

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NThomas Abraham <thomas.ab@samsung.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>
      ddeac8d9
    • B
      clk: add CLK_RECALC_NEW_RATES clock flag for Exynos cpu clock support · d8d91987
      由 Bartlomiej Zolnierkiewicz 提交于 
      This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.

The issue happens because clk_core_set_rate_nolock()  calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run.  In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top).  To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.

For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:

Without use of CLK_GET_RATE_NOCACHE flag:

 fout_apll rate: 1200000000
         fout_apll_div_2 rate: 600000000
                 mout_clkout_cpu rate: 600000000
                         div_clkout_cpu rate: 600000000
                                 clkout_cpu rate: 600000000
         mout_apll rate: 1200000000
                 armclk rate: 1200000000
                 mout_hpm rate: 1200000000
                         div_copy rate: 300000000
                                 div_hpm rate: 300000000
                 mout_core rate: 1200000000
                         div_core rate: 1200000000
                                 div_core2 rate: 1200000000
                                         arm_clk_div_2 rate: 600000000
                                         div_corem0 rate: 300000000
                                         div_corem1 rate: 150000000
                                         div_periph rate: 300000000
                         div_atb rate: 300000000
                                 div_pclk_dbg rate: 150000000
                 sclk_apll rate: 1200000000
                         sclk_apll_div_2 rate: 600000000

With use of CLK_GET_RATE_NOCACHE flag:

 fout_apll rate: 1200000000
         fout_apll_div_2 rate: 600000000
                 mout_clkout_cpu rate: 600000000
                         div_clkout_cpu rate: 600000000
                                 clkout_cpu rate: 600000000
         mout_apll rate: 1200000000
                 armclk rate: 1200000000
                 mout_hpm rate: 1200000000
                         div_copy rate: 200000000
                                 div_hpm rate: 200000000
                 mout_core rate: 1200000000
                         div_core rate: 1200000000
                                 div_core2 rate: 1200000000
                                         arm_clk_div_2 rate: 600000000
                                         div_corem0 rate: 300000000
                                         div_corem1 rate: 150000000
                                         div_periph rate: 300000000
                         div_atb rate: 240000000
                                 div_pclk_dbg rate: 120000000
                 sclk_apll rate: 150000000
                         sclk_apll_div_2 rate: 75000000

Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.

This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.

Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NMichael Turquette <mturquette@baylibre.com>
      d8d91987
  11. 19 6月, 2015 10 次提交