[why]
We are disabling clock source while other pipes are still using
it, because we don't verify the number of pipes that share it.

[how]
- Adding a function in resources to return the number of pipes
sharing the clock source.
- Checking that no one is sharing the clock source before disabling
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[why]
HDMI and DVI share the same PHY clock and single link
DVI and HDMI both use 4 lanes, so they should be allowed
to be sharing the same clock source if all other parameters
are satisfied.

[how]
Change a check for general DVI to Dual DVI.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
DOUBLE_BUFFER_EN bit is getting cleared before enable blanking.
That leads to CRTC_BLANK_DATA_EN is getting updated immediately.

[How]
Get DOUBLE_BUFFER_EN bit set, the same as DCE110.
Signed-off-by: NJerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NCharlene Liu <charlene.liu@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Entity init should after ring init, as the entity's sched_rq's initialization
is in ring init.

SWDEV-161495
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Entity init should after ring init, as the entity's sched_rq's initialization
is in ring init.

SWDEV-161495
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Setup psp firmware loading for VCN, and make VCN block
booting from tmr mac address.
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Add VCN support in PSP driver
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Add the new firmware id for VCN into the enum
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Update tmr mc address with firmware loading address
which is returned from PSP firmware
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

amdgpu IP blocks booting need Trust Memory Region(tmr) mc address
of its firmware which is loaded by PSP
Signed-off-by: NJames Zhu <James.Zhu@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Acked-by: NHuang Rui <ray.huang@amd.com>
Reviewed-by: NLikun Gao <likun.gao@amd.com>
Signed-off-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

More fixes for 4.19:
- Fixes for scheduler
- Fix for SR-IOV
- Fixes for display
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180809200052.2777-1-alexander.deucher@amd.com

drm/imx: ipu-v3 plane offset and IPU id fixes

- Fix U/V plane offsets for odd vertical offsets. Due to wrong operator
  order, the y offset was not rounded down properly for vertically
  chroma subsampled planar formats.
- Fix IPU id number for boards that don't have an OF alias for their
  single IPU in the device tree. This is necessary to support imx-media
  on i.MX51 and i.MX53 SoCs.
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1533552680.4204.14.camel@pengutronix.de

drm/imx: use suspend/resume helpers, add ipu-v3 V4L2 XRGB32/XBGR32 support

- Convert imx_drm_suspend/resume to use the
  drm_mode_config_helper_suspend/ resume functions.
- Add support for V4L2_PIX_FMT_XRGB32/XBGR32, corresponding to
  DRM_FORMAT_XRGB8888/BGRX8888, respectively.
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/1533552701.4204.15.camel@pengutronix.de

Extend the timeout for recovering vram bos from shadows on sr-iov
to cover the worst case scenario for timeslices and VFs

Under runtime, the wait fence time could be quite long when
other VFs are in exclusive mode. For example, for 4 VF, every
VF's exclusive timeout time is set to 3s, then the worst case is
9s. If the VF number is more than 4,then the worst case time will
be longer.
The 8s is the test data, with setting to 8s, it will pass the TDR
test for 1000 times.

SWDEV-161490
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

We no longer have sched parameter so remove its description
as well
Signed-off-by: NNayan Deshmukh <nayan26deshmukh@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Merge tag 'drm-intel-next-fixes-2018-08-06' of git://anongit.freedesktop.org/drm/drm-intel into drm-next

- Fix gvt compilation broken on a silent conflict on fixes vs next merge
- Fix runtime PM for LPE audio
- Revert on ICL workaround
- Interactive RPS mode
- Fix for PSR sink status report
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180806233034.GA20655@intel.com

Merge tag 'drm-misc-next-fixes-2018-08-02' of git://anongit.freedesktop.org/drm/drm-misc into drm-next

Fixes an oops on the DP CEC code and a memory leak on the vkms driver.
Signed-off-by: NDave Airlie <airlied@redhat.com>
From: Gustavo Padovan <gustavo@padovan.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802111728.GA27945@juma

Fixes for 4.19:
- Fix UVD 7.2 instance handling
- Fix UVD 7.2 harvesting
- GPU scheduler fix for when a process is killed
- TTM cleanups
- amdgpu CS bo_list fixes
- Powerplay fixes for polaris12 and CZ/ST
- DC fixes for link training certain HMDs
- DC fix for vega10 blank screen in certain cases

From: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180801222906.1016-1-alexander.deucher@amd.com

From: Lucas Stach <l.stach@pengutronix.de>
"not much to de-stage this time. Changes from Philipp and Souptick to
use memset32 more and switch the fault handler to the new vm_fault_t
and two small fixes for issues that can be hit in rare corner cases
from me."
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1533563808.2809.7.camel@pengutronix.de

From: Russell King <rmk@armlinux.org.uk>
As per the patches posted, discussed and tested by Peter Rosin, this
converts TDA998x to a bridge driver, while still allowing Armada and
TI LCDC to continue using it as they always have done.  It also gets
rid of the private .fill_modes function, and tweaks the TMDS divider
calculation to be more correct to the available information.

[airlied: fixed two conflicts]
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180802093421.GA29670@rmk-PC.armlinux.org.uk

From: Liviu Dudau <Liviu.Dudau@arm.com>
"I managed to loose track of a few patches for HDLCD while focusing
on Mali DP and found them again when investigating an issue with
the way HDLCD behaves on teardown. They can go into drm-next for
one of the v4.19-rcX if you're not going to do another pull request
before the merge window."
Signed-off-by: NDave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180731170831.GF17455@e110455-lin.cambridge.arm.com

The serializer PLL divider is a power-of-two divider, so our calculation
which assumes that it's a numerical divider is incorrect.  Replace it
with one that results in a power-of-two divider value instead.

Tested with all supported modes with a Samsung S24C750.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

We can achieve the same effect via the get_modes() method, rather than
wrapping the fill_modes helper.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Move the mode_valid() implementation to the bridge instead of the
connector, as we're checking the bridge's capabilities.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Register the bridge outside of the component helper as we have
drivers that wish to use the tda998x without its encoder.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Cleanup the code a little from the effects of the previous changes:
- Move tda998x_destroy() to be above tda998x_create()
- Use 'dev' directly in tda998x_create() where appropriate.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Move the tda998x_priv allocation inside tda998x_create() and simplify
the tda998x_create()'s arguments.  Pass the same to tda998x_destroy().
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

Convert tda998x to a bridge driver with built-in encoder support for
compatibility with existing component drivers.
Tested-by: NPeter Rosin <peda@axentia.se>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>

drm_sched_job_finish() is a work item scheduled for each finished job on
a unbound system workqueue. This means the workers can execute out of order
with regard to the real hardware job completions.

If this happens queueing a timeout worker for the first job on the ring
mirror list is wrong, as this may be a job which has already finished
executing. Fix this by reorganizing the code to always queue the worker
for the next job on the list, if this job hasn't finished yet. This is
robust against a potential reordering of the finish workers.

Also move out the timeout worker cancelling, so that we don't need to
take the job list lock twice. As a small optimization list_del is used
to remove the job from the ring mirror list, as there is no need to
reinit the list head in the job we are about to free.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
for vega, dp set_panel_mode is
handled by psp firmware. dal should not program the
register again.

[how]
dal does not program panel mode.
Signed-off-by: NHersen Wu <hersenxs.wu@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
When programming tonga's connector's backend we didn't take
in account that HDMI's colour depth might be more than 8bpc
therefore we need to add a switch statement that would adjust
the pixel clock accordingly.

[how]
Add a switch statement updating clock by its appropriate
coefficient.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NCharlene Liu <Charlene.Liu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[Why]
We seem to have an issue where high enough display clock
will not get set properly during S3 resume if we only
call vbios once

[How]
Expand condition of display clock programming to happen
even when cached display clock matches requested display
clock
Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NTony Cheng <Tony.Cheng@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]

The pointer for integrated_info can be NULL which causes the system to
do a null pointer deference and hang on boot.

[How]

Add a check to ensure that integrated_info is not null before enabling
DP ss.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NSun peng Li <Sunpeng.Li@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Signed-off-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: NEric Bernstein <Eric.Bernstein@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[why]
Prevent clock source sharing between HDMI and DP connectors.
DP shouldn't be sharing its ref clock with phy clock,
which caused an issue of older ASICS booting up with multiple
diplays plugged in.

[how]
Add an extra check that would prevent HDMI and DP sharing clk.
Signed-off-by: NMikita Lipski <mikita.lipski@amd.com>
Reviewed-by: NHersen Wu <hersenxs.wu@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

[why] dp hbr2 eye diagram pattern for raven asic is not stabled.
workaround is to use tp4 pattern. But this should not be
applied to asic before raven.

[how] add new bool varilable in asic caps. for raven asic,
use the workaround. for carrizo, vega, do not use workaround.
Signed-off-by: NHersen Wu <hersenxs.wu@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]

The calculated values for actual disp_clk_khz were ignored when
notifying pplib of the new display requirements. In order to honor DFS
bypass clocks from the hardware, the calculated value should be used.

[How]

The return value for set_dispclk is now assigned back into new_clocks
and correctly carried through into dccg->clks.phyclk_khz. When notifying
pplib of new display requirements dccg->clks.phyclk_khz is used
instead of dce.dispclk_khz. The value of dce.dispclk_khz was never
explicitly set to anything before.

A 15% higher display clock value than calculated is no longer requested
for dce110 since it now makes use of the calculated value.

Since dce112 makes use of dce110's set_bandwidth but not its
update_clocks it needs to have the value correctly carried through.
Signed-off-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Reviewed-by: NDmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
Custom degamma lut functions are a feature we would
like to support on compatible hardware

[How]
In atomic check, convert from array of drm_color_lut to
dc_transfer_func.  On hardware commit, allow for possibility
of custom degamma.  Both are based on the equivalent
regamma pipeline.
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Reviewed-by: NKrunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
In the dce112 function to destroy the resource pool, engines
(the aux engines) is destroyed twice.  This has no ill effects
but is a tad redundant.

[How]
Remove the redundant call
Signed-off-by: NDavid Francis <David.Francis@amd.com>
Reviewed-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>