L_PTE_ASID is not really required to be stored in every PTE, since we
can identify it via the address passed to set_pte_at().  So, create
set_pte_ext() which takes the address of the PTE to set, the Linux
PTE value, and the additional CPU PTE bits which aren't encoded in
the Linux PTE value.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Don't set HWCAP_VFP in the processor support file; not only does it
depend on the processor features, but it also depends on the support
code being present.  Therefore, only set it if the support code
detects that we have a VFP coprocessor attached.

Also, move the VFP handling of the coprocessor access register into
the VFP support code.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The RX3715 is similar to the H1940 in the way
that suspend to RAM works, so we can use most
of the extant support for the H1940 with only
a few modifictions
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The iop348 processor integrates an Xscale (XSC3 512KB L2 Cache) core with a
Serial Attached SCSI (SAS) controller, multi-ported DDR2 memory
controller, 3 Application Direct Memory Access (DMA) controllers, a 133Mhz
PCI-X interface, a x8 PCI-Express interface, and other peripherals to form
a system-on-a-chip RAID subsystem engine.

The iop342 processor replaces the SAS controller with a second Xscale core
for dual core embedded applications.

The iop341 processor is the single core version of iop342.

This patch supports the two Intel customer reference platforms iq81340mc
for external storage and iq81340sc for direct attach (HBA) development.

The developer's manual is available here:
ftp://download.intel.com/design/iio/docs/31503701.pdf

Changelog:
* removed virtual addresses from resource definitions
* cleaned up some unnecessary #include's
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

In light of the recent pagefault and filemap_copy_from_user work I've gone
through all the arch pagefault handlers to make sure the inc_preempt_count()
'feature' works as expected.

Several sections of code (including the new filemap_copy_from_user) rely on
the fact that faults do not take locks under increased preempt count.

arch/x86_64 - good
arch/powerpc - good
arch/cris - fixed
arch/i386 - good
arch/parisc - fixed
arch/sh - good
arch/sparc - good
arch/s390 - good
arch/m68k - fixed
arch/ppc - good
arch/alpha - fixed
arch/mips - good
arch/sparc64 - good
arch/ia64 - good
arch/arm - fixed
arch/um - good
arch/avr32 - good
arch/h8300 - NA
arch/m32r - good
arch/v850 - good
arch/frv - fixed
arch/m68knommu - NA
arch/arm26 - fixed
arch/sh64 - fixed
arch/xtensa - good
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add support to suspend and resume, using the
H1940's bootloader
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

XScale cores either have a DSP coprocessor (which contains a single
40 bit accumulator register), or an iWMMXt coprocessor (which contains
eight 64 bit registers.)

Because of the small amount of state in the DSP coprocessor, access to
the DSP coprocessor (CP0) is always enabled, and DSP context switching
is done unconditionally on every task switch.  Access to the iWMMXt
coprocessor (CP0/CP1) is enabled only when an iWMMXt instruction is
first issued, and iWMMXt context switching is done lazily.

CONFIG_IWMMXT is supposed to mean 'the cpu we will be running on will
have iWMMXt support', but boards are supposed to select this config
symbol by hand, and at least one pxa27x board doesn't get this right,
so on that board, proc-xscale.S will incorrectly assume that we have a
DSP coprocessor, enable CP0 on boot, and we will then only save the
first iWMMXt register (wR0) on context switches, which is Bad.

This patch redefines CONFIG_IWMMXT as 'the cpu we will be running on
might have iWMMXt support, and we will enable iWMMXt context switching
if it does.'  This means that with this patch, running a CONFIG_IWMMXT=n
kernel on an iWMMXt-capable CPU will no longer potentially corrupt iWMMXt
state over context switches, and running a CONFIG_IWMMXT=y kernel on a
non-iWMMXt capable CPU will still do DSP context save/restore.

These changes should make iWMMXt work on PXA3xx, and as a side effect,
enable proper acc0 save/restore on non-iWMMXt capable xsc3 cores such
as IOP13xx and IXP23xx (which will not have CONFIG_CPU_XSCALE defined),
as well as setting and using HWCAP_IWMMXT properly.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove BTB_ENABLE from proc-xsc3.S

On some early revisions of xsc3 enabling the branch target buffer can cause
crashes, see erratum #42.

Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge L_PTE_COHERENT with L_PTE_SHARED and free up a L_PTE_* bit.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix warnings and errors in arch/arm/mm for nommu build.
Remove commented out function prototype in pgtable-nommu.h
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

These files want to provide/access ELF hwcap information, so should
be including asm/elf.h rather than asm/procinfo.h
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix various Kconfig typos.
Signed-off-by: NMatt LaPlante <kernel1@cyberdogtech.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

/*
 * Note: Drivers should NOT use this function directly, as it will break
 * platforms with CONFIG_DMABOUNCE.
 * Use the driver DMA support - see dma-mapping.h (dma_sync_*)
 */
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

show_mem() was not correctly handling holes in the memory
map.  It was treating the freed sections of the map as
though they contained valid struct page entries.  This
could cause incorrect debugging output or even a kernel
panic.

This patch keeps the struct meminfo around after system
initialization so that show_mem() can use it when
scanning memory.  show_mem() now walks over each bank
of each online node, rather than assuming that each node
contains a single contiguous bank.
Signed-off-by: NRay Lehtiniemi <rayl@mail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

ARM patch 3756/1 added HWCAP_IWMMXT.  This patch adds support
for broadcasting that info via /proc/cpuinfo and sets it for
the CPU features of the PXA270.

I've booted 19rc3 on a pxa270 and confirmed that the /proc/cpuinfo
shows "iwmmxt" in the Features.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

XIP kernels need to know the start/end of text, but we were
missing the declaration of _etext in mmu.c.  Add it.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This is an updated version of Eric Biederman's is_init() patch.
(http://lkml.org/lkml/2006/2/6/280).  It applies cleanly to 2.6.18-rc3 and
replaces a few more instances of ->pid == 1 with is_init().

Further, is_init() checks pid and thus removes dependency on Eric's other
patches for now.

Eric's original description:

	There are a lot of places in the kernel where we test for init
	because we give it special properties.  Most  significantly init
	must not die.  This results in code all over the kernel test
	->pid == 1.

	Introduce is_init to capture this case.

	With multiple pid spaces for all of the cases affected we are
	looking for only the first process on the system, not some other
	process that has pid == 1.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NSukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: <lxc-devel@lists.sourceforge.net>
Acked-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Make PROT_WRITE imply PROT_READ for a number of architectures which don't
support write only in hardware.

While looking at this, I noticed that some architectures which do not
support write only mappings already take the exact same approach.  For
example, in arch/alpha/mm/fault.c:

"
        if (cause < 0) {
                if (!(vma->vm_flags & VM_EXEC))
                        goto bad_area;
        } else if (!cause) {
                /* Allow reads even for write-only mappings */
                if (!(vma->vm_flags & (VM_READ | VM_WRITE)))
                        goto bad_area;
        } else {
                if (!(vma->vm_flags & VM_WRITE))
                        goto bad_area;
        }
"

Thus, this patch brings other architectures which do not support write only
mappings in-line and consistent with the rest.  I've verified the patch on
ia64, x86_64 and x86.

Additional discussion:

Several architectures, including x86, can not support write-only mappings.
The pte for x86 reserves a single bit for protection and its two states are
read only or read/write.  Thus, write only is not supported in h/w.

Currently, if i 'mmap' a page write-only, the first read attempt on that page
creates a page fault and will SEGV.  That check is enforced in
arch/blah/mm/fault.c.  However, if i first write that page it will fault in
and the pte will be set to read/write.  Thus, any subsequent reads to the page
will succeed.  It is this inconsistency in behavior that this patch is
attempting to address.  Furthermore, if the page is swapped out, and then
brought back the first read will also cause a SEGV.  Thus, any arbitrary read
on a page can potentially result in a SEGV.

According to the SuSv3 spec, "if the application requests only PROT_WRITE, the
implementation may also allow read access." Also as mentioned, some
archtectures, such as alpha, shown above already take the approach that i am
suggesting.

The counter-argument to this raised by Arjan, is that the kernel is enforcing
the write only mapping the best it can given the h/w limitations.  This is
true, however Alan Cox, and myself would argue that the inconsitency in
behavior, that is applications can sometimes work/sometimes fails is highly
undesireable.  If you read through the thread, i think people, came to an
agreement on the last patch i posted, as nobody has objected to it...
Signed-off-by: NJason Baron <jbaron@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NAndi Kleen <ak@muc.de>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In nommu mode, the exception vector location depends on the platforms.
Some of the implementations may have some special exception control
forwarding method in their ROM/flash and for some of them has its own
re-mapping mechanism by the h/w.

This patch introduces a special configuration CONFIG_CPU_HIGH_VECTOR which
turns on the CR_V bit in nommu mode. The CR_V bit is turned off by default.
This feature depends on CP15 and does not supported by ARM740.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There is no FSR/FAR register on no-CP15 or MPU cores. This patch adds a
dummy abort handler which returns zero for the base restored Data Abort
model !CPU_CP15_MMU cores. The abort-lv4t.S is still used with the fix-up
for the base updated Data Abort model cores.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Don't offer non-MMU based CPUs for selection when CONFIG_MMU is
set.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM946E-S core support which has typically 8KB I&D cache.
It has a MPU and supports ARMv5TE instruction set.

Because the ARM946E-S core can be synthesizable with various cache size,
CONFIG_CPU_DCACHE_SIZE is defined for vendor specific configurations.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM940T core support which has 4KB D-cache, 4KB I-cache
and a MPU.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM9TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM740T core support which has a MPU and 4KB or 8KB cache.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch adds ARM7TDMI core support which has no cache and no CP15
register(no memory control unit).
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

All the current CP15 access codes in ARM arch can be categorized and
conditioned by the defines as follows:

     Related operation	Safe condition
  a. any CP15 access	!CPU_CP15
  b. alignment trap	CPU_CP15_MMU
  c. D-cache(C-bit)	CPU_CP15
  d. I-cache		CPU_CP15 && !( CPU_ARM610 || CPU_ARM710 ||
				CPU_ARM720 || CPU_ARM740 ||
				CPU_XSCALE || CPU_XSC3 )
  e. alternate vector	CPU_CP15 && !CPU_ARM740
  f. TTB		CPU_CP15_MMU
  g. Domain		CPU_CP15_MMU
  h. FSR/FAR		CPU_CP15_MMU

For example, alternate vector is supported if and only if
"CPU_CP15 && !CPU_ARM740" is satisfied.
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

By merging of uClinux/ARM, we need to treat various CPU cores which have
MMU, MPU or even none for memory management. The memory management
coprocessors are controlled by CP15 register set and the ARM core family
can be categorized by 5 groups by the register ;
  G-a. CP15 is MMU : 610, 710, 720, 920, 922, 925, 926, 1020, 1020e, 1022,
		v6 and the derivations sa1100, sa110, xscale, xsc3.
  G-b. CP15 is MPU : 740, 940, 946, 996, 1156.
  G-c. CP15 is MPU or MMU : 1026 (selectable by schematic design)
  G-d. CP15 is exist, but nothing for memory managemnt : 966, 968.
  G-e. no-CP15 : 7tdmi, 9tdmi, 9e, 9ej

This patch defines CPU_CP15, CPU_CP15_MMU and CPU_CP15_MPU. Thus the
family can be defined as :
  - CPU_CP15 only : G-d
  - CPU_CP15_MMU(implies CPU_CP15) : G-a, G-c(selectable)
  - CPU_CP15_MPU(implies CPU_CP15) : G-b, G-c(selectable)
  - !CPU_CP15 : G-e
Signed-off-by: NHyok S. Choi <hyok.choi@samsung.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since do_bad_area() always takes the currently active task and
(supposed to) take the currently active MM, there's no point passing
them to this function.  Instead, obtain references to them inside
do_bad_area().
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add an empty setup_mm_for_reboot() function for nommu machines.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

mm-armv.c now only contains the pgd allocation/freeing code, so
rename it to have a more sensible filename.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

If we're going to have mmu.c for code which is specific to the MMU
machines, we might as well move the other MMU initialisation
specific code from mm-armv.c into this new file.  This also allows
us to make some functions static.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Move the MMU specific code from init.c into mmu.c, and add nommu
fixups to nommu.c
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

nommu does not require the page table manipulation code in the
bootmem initialisation paths.  Move this into separate inline
functions.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM XIP_KERNEL map created in devicemaps_init() is wrong.
The map.pfn is rounded down to an even 1MiB section boundary
which results in va/pa translations errors when XIP_PHYS_ADDR
starts on an odd 1MiB boundary and this causes the kernel to
hang.  This patch fixes ARM XIP_KERNEL translation errors for
the odd 1MiB XIP_PHYS_ADDR boundary case.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

One of the changes necessary for shared page tables is to standardize the
pxx_page macros.  pte_page and pmd_page have always returned the struct
page associated with their entry, while pte_page_kernel and pmd_page_kernel
have returned the kernel virtual address.  pud_page and pgd_page, on the
other hand, return the kernel virtual address.

Shared page tables needs pud_page and pgd_page to return the actual page
structures.  There are very few actual users of these functions, so it is
simple to standardize their usage.

Since this is basic cleanup, I am submitting these changes as a standalone
patch.  Per Hugh Dickins' comments about it, I am also changing the
pxx_page_kernel macros to pxx_page_vaddr to clarify their meaning.
Signed-off-by: NDave McCracken <dmccr@us.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix thinko in the flush_ptrace_access() "if (expr)" for the ARM
VIPT non-aliasing cache case.  We only need to flush cache when
VM_EXEC is set in vma->vm_flags but "if (expr) always evaluates
to true on UP systems for the ARM VIPT non-aliasing cache case.
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Split the iop3xx mach type into iop32x and iop33x -- split the config
symbols, and move the code in the mach-iop3xx directory to the mach-iop32x
and mach-iop33x directories.
Signed-off-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>