Fix TS input over I2S.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Small modifications for firmware 18.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Card driver may supply its own lock routine now.
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The STV0900 features two demodulator paths in one chip. Thus it is not
possible to use the generic power off function of the chip when sending
one of them to standby. The other path will stop working in that case.

The sleep function now switches off functionality specific to the demod
path. The global stuff is only switched off, when both paths are in
sleep mode. The wakeup function always turns on the global functionality
and then works specific to the path.
Signed-off-by: NAndreas Regel <andreas.regel@gmx.de>
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Something went wrong with the alignments for the if clause at line 2113.
Instead of using one tab for alignments, it used 3 tabs, plus one space
character.

WARNING: suspect code indent for conditional statements (8, 33)
+	if ((state->fe[0]->dtv_property_cache.delivery_system != SYS_ISDBT) ||
[...]
+				 int i = 80000;

WARNING: suspect code indent for conditional statements (33, 41)
+				 for (index_frontend = 0; (index_frontend < MAX_NUMBER_OF_FRONTENDS) && (state->fe[index_frontend] != NULL); index_frontend++) {
+					 dib8000_set_bandwidth(state->fe[index_frontend], fe->dtv_property_cache.bandwidth_hz / 1000);

WARNING: suspect code indent for conditional statements (33, 41)
+				 do {
+					 msleep(20);

WARNING: suspect code indent for conditional statements (41, 49)
+					 for (index_frontend = 0; (index_frontend < MAX_NUMBER_OF_FRONTENDS) && (state->fe[index_frontend] != NULL); index_frontend++) {
+						 if (((tune_failed >> index_frontend) & 0x1) == 0) {

WARNING: suspect code indent for conditional statements (49, 57)
+						 if (((tune_failed >> index_frontend) & 0x1) == 0) {
+							 found = dib8000_autosearch_irq(state->fe[index_frontend]);

WARNING: suspect code indent for conditional statements (41, 49)
+					 if ((nbr_pending == 0) && (exit_condition == 0))
+						 exit_condition = 1;

Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

ERROR: switch and case should be at the same indent
 	switch (ch->u.ofdm.transmission_mode) {
[...]
+    case TRANSMISSION_MODE_4K:

WARNING: please, no spaces at the start of a line
+    case TRANSMISSION_MODE_4K:$

ERROR: switch and case should be at the same indent
 	switch (ch->u.ofdm.transmission_mode) {
[...]
+    case TRANSMISSION_MODE_4K:

WARNING: please, no spaces at the start of a line
+    case TRANSMISSION_MODE_4K:$

ERROR: switch and case should be at the same indent
 	switch (ch->u.ofdm.transmission_mode) {
[...]
+    case TRANSMISSION_MODE_4K:

WARNING: please, no spaces at the start of a line
+    case TRANSMISSION_MODE_4K:$

Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patchs fix several conding-style violations.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patchs adds support for DiBcom's NIM8096MD, NIM9090M, NIM9090MD,
NIM7090, TFE7090PVR (no diversity) reference designs.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for the SoC DiB7090 DVB-T demodulator and its
melt-in UHF/VHF RF tuner.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patchs add initial support for the DiB9000-device. This
demodulator is firmware-driven.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds several performance improvements and prepares the
usage of firmware-based devices.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds the possibitity to use different I2C-ports to talk to
slave-devices than the standard ones.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a set a functions which allow the handling of multiple
demodulator in a diversity reception chain.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This commit adds a function to the DiB0700 USB driver which allows
drivers to change the I2C clock speed.
Signed-off-by: NOlivier Grenie <olivier.grenie@dibcom.fr>
Signed-off-by: NPatrick Boettcher <patrick.boettcher@dibcom.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add I2C/V4L2 subdev driver for Siliconfile NOON010PC30 CIF camera.
The driver implements basic functionality, i.e. CIF/QCIF/QQCIF
resolution and color format selection, automatic/manual color
balance control. Other functions like cropping, rotation/flip,
exposure etc. can be easily implemented if needed.
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add ID for NOON010PC30 camera chip and reserve ID range for
Siliconfile sensors.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When is called fimc_stop_capture, it seems that wait_event_timeout
used improperly. It should be wake up by irq handler.

Reviewed-by Jonghun Han <jonghun.han@samsung.com>
Signed-off-by: NSungchun Kang <sungchun.kang@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes the value of FIFO_CTRL in MSCTRL.
Main-scaler has the value to specify a basis FIFO control of input DMA.

The description of FIFO_CTRL has been changed as below.
0 = FIFO Empty (Next burst transaction is possible when FIFO is empty)
1 = FIFO Full (Next burst transaction is possible except Full FIFO)

Value '1' is recommended to enhance the FIMC operation performance.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds callback functions, stop_streaming and job_abort,
to abort or finish any DMA in progress. stop_streaming is called
by videobuf2 framework and job_abort is called by m2m framework.
ST_M2M_PEND state is added to discard the next job.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Horizontal and vertical scaling range are according to the following equations.
If (SRC_Width >= 64 x DST_Width) { Exit(-1);  /* Out of Horizontal scale range}
If (SRC_Height >= 64 x DST_Height) { Exit(-1);  /* Out of Vertical scale range}

fimc_check_scaler_ratio() is used to check if horizontal and vertical
scale range are valid or not. To use fimc_check_scaler_ratio,
source and destination format should be set by VIDIOC_S_FMT.
And in case of scaling up, it doesn't have to check the scale range.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The main scaler has four SFRs for main scaler ratio depending on FIMC version.
FIMC 4.x has only two SFRs and FIMC 5.x has four SFRs for main scaler.
Those are MainHorRatio, MainHorRatio_ext, MainVerRatio and MainverRatio_ext.

The FIMC 5.x has 15 bit resolution for scaling ratio as below.
{MainHorRatio,MainHorRatio_ext} = {[14:6],[5:0]}.
{MainVerRatio,MainVerRatio_ext} = {[14:6],[5:0]}.
MainHorRatio = CISCCTRL[24:16], MainHorRatio_ext = CIEXTEN[15:10]
MainVerRatio = CISCCTRL[8:0],   MainVerRatio_ext = CIEXTEN[5:0]

This patch supports FIMC 4.x and FIMC 5.x using platform_device_id::driver_data.
Reviewed-by: NJonghun Han <jonghun.han@samsung.com>
Signed-off-by: NHyunwoong Kim <khw0178.kim@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some color formats are mismatched in s5p-fimc driver.
CIOCTRL[1:0], order422_out, should be set 2b'00 not 2b'11
to use V4L2_PIX_FMT_YUYV. Because in V4L2 standard V4L2_PIX_FMT_YUYV means
"start + 0: Y'00 Cb00 Y'01 Cr00 Y'02 Cb01 Y'03 Cr01". According to datasheet
2b'00 is right value for V4L2_PIX_FMT_YUYV.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Manage the camera sensor clock in the host driver rather than
leaving this task for sensor drivers. The clock frequency
must be passed in the sensor's and host driver's platform data.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Map all (0, 90, 180, 270) deg counterclockwise rotation and
horizontal and vertical flip controls to (0, 90) deg rotation,
horizontal and vertical flip transformations available
in the device.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Increase the input DMA "successive burst count" to default
value 4 to improve DMA performance. Minor cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Prevent VIDIOC_STREAMON failing when s_stream callback is
not implemented by a sensor subdev driver.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove bus_width from s5p_fimc_isp_info data structure.
Determine camera data bus width based on mediabus pixel format.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Change s3c_fimc.h header file name to s5p_fimc.h, replace s3c_fimc_*
names with s5p_fimc_*. s3c_fimc need to be reserved for S3C series
and s5p-fimc driver will not cover CAMIF devices in S3C SoC series.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Conversion to multiplanar color formats and minor cleanup.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Porting to videobuf 2 and minor cleanup.
Separate videobuf_queue_ops are are created for m2m
and capture video nodes.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add definitions for format with color planes non-contiguous
in physical memory. These formats apply only if the V4L2 multiplane
extension is used.

V4L2_PIX_FMT_NV12M   - 2-plane Y/CbCr
V4L2_PIX_FMT_NV12MT  - 2-plane Y/CbCr tiled (64x32 pixel macroblocks)
V4L2_PIX_FMT_YUV420M - 3-plane Y/Cb/Cr
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch ports mem2mem test device to videobuf2 framework.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Port memory-to-memory framework to videobuf2 framework.

Add support for multi-planar Video for Linux 2 API extensions to the
memory-to-memory driver framework.

Based on the original patch written by Pawel Osciak.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add DocBook documentation for the new multi-planar API extensions to the
Video for Linux 2 API DocBook.
Signed-off-by: NPawel Osciak <pawel@osciak.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Correct ioctl return value handling and fix coding style issues.

[mchehab@redhat.com: return -1 is OK, according with ioctl manpages. Reverting ioctl changes]
Signed-off-by: NPawel Osciak <pawel@osciak.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/video/videobuf2-core.c: In function ‘__vb2_perform_fileio’:
drivers/media/video/videobuf2-core.c:1638: warning: format ‘%ld’ expects type ‘long int’, but argument 4 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1697: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
drivers/media/video/videobuf2-core.c:1703: warning: format ‘%ld’ expects type ‘long int’, but argument 2 has type ‘size_t’
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a generic file io (read and write) emulator for videobuf2. It uses
MMAP memory type buffers and generic vb2 calls: req_bufs, qbuf and
dqbuf. Video date is being copied from mmap buffers to userspace with
standard copy_to_user() function. To add support for file io the driver
needs to provide an additional callback - read_setup or write_setup. It
should provide the default number of buffers used by emulator and flags.

With these flags one can detemine the style of read() or write()
emulation. By default 'streaming' style is used. With
VB2_FILEIO_READ_ONCE flag one can select 'one shot' mode for read()
emulator. With VB2_FILEIO_WRITE_IMMEDIATE flag one can select immediate
conversion of write calls to qbuf for write() emulator, so the vb2 will
not wait until each buffer is filled completely before queueing it to
the driver.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
CC: Pawel Osciak <pawel@osciak.com>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>