This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit c21e6beb removed our queue request_fn re-enter
protection, and defaulted to always running the queues from
kblockd to be safe. This was a known potential slow down,
but should be safe.

Unfortunately this is causing big performance regressions for
some, so we need to improve this logic. Looking into the details
of the re-enter, the real issue is on requeue of requests.

Requeue of requests upon seeing a BUSY condition from the device
ends up re-running the queue, causing traces like this:

scsi_request_fn()
        scsi_dispatch_cmd()
                scsi_queue_insert()
                        __scsi_queue_insert()
                                scsi_run_queue()
					scsi_request_fn()
						...

potentially causing the issue we want to avoid. So special
case the requeue re-run of the queue, but improve it to offload
the entire run of local queue and starved queue from a single
workqueue callback. This is a lot better than potentially
kicking off a workqueue run for each device seen.

This also fixes the issue of the local device going into recursion,
since the above mentioned commit never moved that queue run out
of line.
Signed-off-by: NJens Axboe <jaxboe@fusionio.com>

During device discovery, scsi mid layer sends INQUIRY command to LUN
0. If the LUN 0 is not mapped to host, it creates a temporary
scsi_device with LUN id 0 and sends REPORT_LUNS command to it. After
the REPORT_LUNS succeeds, it walks through the LUN table and adds each
LUN found to sysfs. At the end of REPORT_LUNS lun table scan, it will
delete the temporary scsi_device of LUN 0.

When scsi devices are added to sysfs, it calls add_dev function of all
the registered class interfaces. If ses driver has been registered,
ses_intf_add() of ses module will be called. This function calls
scsi_device_enclosure() to check the inquiry data for EncServ
bit. Since inquiry was not allocated for temporary LUN 0 scsi_device,
it will cause NULL pointer exception.

To fix the problem, sdev->inquiry is checked for NULL before reading it.
Signed-off-by: NSomasundaram Krishnasamy <Somasundaram.Krishnasamy@lsi.com>
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Previously we were using strncmp in order to avoid having to include
whitespace in the devlist, but this means "HSV1000" matches a device
list entry that says "HSV100", which is wrong.  This patch changes
scsi_dh.c to use scsi_devinfo's matching functions instead, since they
handle these cases correctly.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

I seem to have a knack for digging up buggy usb devices which don't work
with Linux, and I'm crazy enough to try to make them work.  So this time a
friend of mine asked me to get an mp4 player (an mp3 player which can play
videos on a small screen) to work with Linux.

It is based on the well known rockbox chipset for which we already have an
unusual devs entries to work around some of its bugs.  But this model
comes with an additional twist.

This model chokes on read_capacity_16 calls.  Now normally we don't make
those calls, but this model comes with an sdcard slot and when there is no
card in there (and shipped from the factory there is none), it reports a
size of 0.  However this time the programmers actually got the
read_capacity_10 response right!  So they substract one from the size as
stored internally in the mp3 player before reporting it back, resulting in
an answer of ...  0xffffffff sectors, causing sd.c to try a
read_capacity_16, on which the device crashes.

This patch adds a flag to scsi_device to indicate that a a device cannot
handle read_capacity_16, and when this flag is set if a device reports an
lba of 0xffffffff as answer to a read_capacity_10, assumes it tries to
report a size of 0.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some USB devices emulate a usb-mass-storage attached (scsi) cdrom device,
usually this fake cdrom contains the windows software for the device.
While working on supporting Appotech ax3003 based photoframes, which do
this I discovered that they will go of into lala land when ever they see a
READ_DISC_INFO scsi command.

Thus this patch adds a scsi_device flag (which can then be set by the
usb-storage driver through an unsual-devs entry), to indicate this, and
makes the sr driver honor this flag.

I know this sucks, but as discussed on linux-scsi list there is no other
way to make this device work properly.

Looking at usb traces made under windows, windows never sends a
READ_DISC_INFO during normal interactions with a usb cdrom device.  So as
this cdrom emulation thingie becomes more common we might see more of this
problem.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1398b) adds runtime PM support to the SCSI layer.  Only
the machanism is provided; use of it is up to the various high-level
drivers, and the patch doesn't change any of them.  Except for sg --
the patch expicitly prevents a device from being runtime-suspended
while its sg device file is open.

The implementation is simplistic.  In general, hosts and targets are
automatically suspended when all their children are asleep, but for
them the runtime-suspend code doesn't actually do anything.  (A host's
runtime PM status is propagated up the device tree, though, so a
runtime-PM-aware lower-level driver could power down the host adapter
hardware at the appropriate times.)  There are comments indicating
where a transport class might be notified or some other hooks added.

LUNs are runtime-suspended by calling the drivers' existing suspend
handlers (and likewise for runtime-resume).  Somewhat arbitrarily, the
implementation delays for 100 ms before suspending an eligible LUN.
This is because there typically are occasions during bootup when the
same device file is opened and closed several times in quick
succession.

The way this all works is that the SCSI core increments a device's
PM-usage count when it is registered.  If a high-level driver does
nothing then the device will not be eligible for runtime-suspend
because of the elevated usage count.  If a high-level driver wants to
use runtime PM then it can call scsi_autopm_put_device() in its probe
routine to decrement the usage count and scsi_autopm_get_device() in
its remove routine to restore the original count.

Hosts, targets, and LUNs are not suspended while they are being probed
or removed, or while the error handler is running.  In fact, a fairly
large part of the patch consists of code to make sure that things
aren't suspended at such times.

[jejb: fix up compile issues in PM config variations]
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The best way to fix this is to eliminate the intenal kmalloc() and
make the caller allocate the required amount of storage.
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Make scsi_dh_activate() function asynchronous, by taking in two additional
parameters, one is the callback function and the other is the data to call
the callback function with.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Current FC HBA queue_depth ramp up code depends on last queue
full time. The sdev already  has last_queue_full_time field to
track last queue full time but stored value is truncated by
last four bits.

So this patch updates last_queue_full_time without truncating
last 4 bits to store full value and then updates its only
current usages in scsi_track_queue_full to ignore last four bits
to keep current usages same while also use this field
in added ramp up code.

Adds scsi_handle_queue_ramp_up to ramp up queue_depth on
successful completion of IO. The scsi_handle_queue_ramp_up will
do ramp up on all luns of a target, just same as ramp down done
on all luns on a target.

The ramp up is skipped in case the change_queue_depth is not
supported by LLD or already reached to added max_queue_depth.

Updates added max_queue_depth on every new update to default
queue_depth value.

The ramp up is also skipped if lapsed time since either last
queue ramp up or down is less than LLD specified
queue_ramp_up_period.

Adds queue_ramp_up_period to sysfs but only if change_queue_depth
is supported since ramp up and queue_ramp_up_period is needed only
in case change_queue_depth is supported first.

Initializes queue_ramp_up_period to 120HZ jiffies as initial
default value, it is same as used in existing lpfc and qla2xxx.

-v2
 Combined all ramp code into this single patch.

-v3
 Moves max_queue_depth initialization after slave_configure is
called from after slave_alloc calling done. Also adjusted
max_queue_depth check to skip ramp up if current queue_depth
is >= max_queue_depth.

-v4
 Changes sdev->queue_ramp_up_period unit to ms when using sysfs i/f
to store or show its value.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Tested-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Tested-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Async scanning introduced a very wide window where the SCSI device is
up and running but has not yet been added to sysfs.  We delay the
adding until all scans have completed to retain the same ordering as
sync scanning.

This delay in visibility causes an oops if a device is removed before
we make it visible because the SCSI removal routines have an inbuilt
assumption that if a device is in SDEV_RUNNING state, it must be
visible (which is not necessarily true in the async scanning case).

Fix this by introducing an additional is_visible flag which we can use
to condition the tear down so we do the right thing for running but
not yet made visible.
Reported-by: NAlexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

When we moved the device handler functionality from dm layer to SCSI layer
we dropped the parameter functionality.

This path adds an interface to scsi dh layer to set device handler
parameters.

Basically, multipath layer need to create a string with all the parameters
and call scsi_dh_set_params() after it called scsi_dh_attach() on a
device.

If a device handler provides such an interface it will handle the parameters
as it expects them.
Reported-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Tested-by: NEddie Williams <Eddie.Williams@steeleye.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Problem reported: http://marc.info/?l=dm-devel&m=124585978305866&w=2

scsi_dh does not do a refernce count for attach/detach, and this affects
the way it is supposed to work with multipath when a device is not
in the dev_list of the hardware handler.

This patch adds a reference count that counts each attach.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

No one uses scsi_execute_async with data transfer now. We can remove
scsi_req_map_sg.

Only scsi_eh_lock_door uses scsi_execute_async. scsi_eh_lock_door
doesn't handle sense and the callback. So we can remove
scsi_io_context too.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

scsi_device_online() is not just a negation of SDEV_OFFLINE,
also devices in state SDEV_DEL are actually offline.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Based on prior work by Martin Petersen and James Bottomley, this patch
adds a generic helper for retrieving VPD pages from SCSI devices.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

scsi_execute() and scsi_execute_req() discard the residual length
information. Some callers need it. This adds residual argument
(optional) to scsi_execute and scsi_execute_req.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

by removing the unused timeout parameter we ensure a compile failure if
anyone is accidentally still using it rather than the block timeout.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

SCSI-ml manages the queueing limits for the device and host, but
does not do so at the target level. However something something similar
can come in userful when a driver is transitioning a transport object to
the the blocked state, becuase at that time we do not want to queue
io and we do not want the queuecommand to be called again.

The patch adds code similar to the exisiting SCSI_ML_*BUSY handlers.
You can now return SCSI_MLQUEUE_TARGET_BUSY when we hit
a transport level queueing issue like the hw cannot allocate some
resource at the iscsi session/connection level, or the target has temporarily
closed or shrunk the queueing window, or if we are transitioning
to the blocked state.

bnx2i, when they rework their firmware according to netdev
developers requests, will also need to be able to limit queueing at this
level. bnx2i will hook into libiscsi, but will allocate a scsi host per
netdevice/hba, so unlike pure software iscsi/iser which is allocating
a host per session, it cannot set the scsi_host->can_queue and return
SCSI_MLQUEUE_HOST_BUSY to reflect queueing limits on the transport.

The iscsi class/driver can also set a scsi_target->can_queue value which
reflects the max commands the driver/class can support. For iscsi this
reflects the number of commands we can support for each session due to
session/connection hw limits, driver limits, and to also reflect the
session/targets's queueing window.

Changes:
v1 - initial patch.
v2 - Fix scsi_run_queue handling of multiple blocked targets.
Previously we would break from the main loop if a device was added back on
the starved list. We now run over the list and check if any target is
blocked.
v3 - Rediff for scsi-misc.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Brian King <brking@linux.vnet.ibm.com> reported that fibre channel
devices can oops during scanning if their ports block (because the
device goes from CREATED -> BLOCK -> RUNNING rather than CREATED ->
BLOCK -> CREATED).

Fix this by adding a new state: CREATED_BLOCK which can only transition
back to CREATED and disallow the CREATED -> BLOCK transition.  Now both
the created and blocked states that the mid-layer recognises can include
CREATED_BLOCK.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The created and blocked states are very shortly going to correspond to
mixed sdev_state states.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some USB devices set the protect bit in the INQUIRY data which
currently causes the DIF code in sd to assume (incorrectly) that they
support READ_CAPACITY(16).  Fix this (only for the time being) by
making sure we only believe the protect bit in the inquiry data if the
device claims conformance to SCSI-3 or above.
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This re-introduces commit 2b142900,
which was reverted due to the regression it caused by commit
fca082c9.

That regression was not root-caused by the original commit, it was just
uncovered by it, and the real fix was done by Alan Stern in commit
580da348 ("Fix USB storage hang on
command abort").

We can thus re-introduce the change that was confirmed by Alan Jenkins
to be still required by his odd card reader.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 2b142900, since it
seems to break some other USB storage devices (at least a JMicron USB to
ATA bridge).  As such, while it apparently fixes some cardreaders, it
would need to be made conditional on the exact reader it fixes in order
to avoid causing regressions.

Cc: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The last_sector_bug flag was added to work around a bug in certain usb
cardreaders, where they would crash if a multiple sector read included the
last sector. The original implementation avoids this by e.g. splitting an 8
sector read which includes the last sector into a 7 sector read, and a single
sector read for the last sector.  The flag is enabled for all USB devices.

This revealed a second bug in other usb cardreaders, which crash when they
get a multiple sector read which stops 1 sector short of the last sector.
Affected hardware includes the Kingston "MobileLite" external USB cardreader
and the internal USB cardreader on the Asus EeePC.

Extend the last_sector_bug workaround to ensure that any access which touches
the last 8 hardware sectors of the device is a single sector long.  Requests
are shrunk as necessary to meet this constraint.

This gives us a safety margin against potential unknown or future bugs
affecting multi-sector access to the end of the device.  The two known bugs
only affect the last 2 sectors.  However, they suggest that these devices
are prone to fencepost errors and that multi-sector access to the end of the
device is not well tested.  Popular OS's use multi-sector accesses, but they
rarely read the last few sectors.  Linux (with udev & vol_id) automatically
reads sectors from the end of the device on insertion.  It is assumed that
single sector accesses are more thoroughly tested during development.
Signed-off-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Tested-by: NAlan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Implement support for DMA of protection information for devices that
are data integrity capable.

 - Add support for mapping an extra scatter-gather list containing
   the protection information.

 - Allocate protection scsi_data_buffer if host is DIX (integrity DMA)
   capable.

 - Accessor function for checking whether a device has protection
   enabled.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Instead of having each and every driver implement its own
device table scanning code we should rather implement a common
routine and scan the device tables there.
This allows us also to implement a general notifier chain
callback for all device handler instead for one per handler.

[sekharan: Fix rejections caused by conflicting bug fix]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Adds a new scsi_device flag, start_stop_pwr_cond:  If enabled, the sd
driver will not send plain START STOP UNIT commands but ones with the
power condition field set to 3 (standby) or 1 (active) respectively.

Some FireWire disk firmwares do not stop the motor if power condition is
zero.  Or worse, they become unresponsive after a START STOP UNIT with
power condition = 0 and start = 0.

http://lkml.org/lkml/2008/4/29/704

This patch only adds the necessary code to sd_mod but doesn't activate
it.  Follow-up patches to the FireWire drivers will add detection of
affected devices and enable the code for them.

I did not add power condition values to scsi_error.c::scsi_eh_try_stu()
for now.  The three firmwares which suffer from above mentioned problems
do not need START STOP UNIT in the error handler, and they are not
adversely affected by START STOP UNIT with power condition = 0 and start
= 1 (like scsi_eh_try_stu() sends it if scsi_device.allow_restart is
enabled).
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NTino Keitel <tino.keitel@gmx.de>

Some of the storage devices (that can be accessed through multiple paths),
do need some special handling for
	1. Activating the passive path of the storage access.
	2. Decode and handle the special sense codes returned by the devices.
	3. Handle the I/Os being sent to the passive path, especially
           during the device probe time.
when accessed through multiple paths.

As of today this special device handling is done at the dm-multipath
layer using dm-handlers. That works well for (1); for (2) to be handled
at dm layer, scsi sense information need to be exported from SCSI to dm-layer,
which is not very attractive; (3) cannot be done at all at the dm layer.

Device handler has been moved to SCSI mainly to handle (2) and (3) properly.
Signed-off-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NMike Anderson <andmike@linux.vnet.ibm.com>
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The current target allocation code registeres each possible target
with sysfs; it will be deleted again if no useable LUN on this target
was found. This results in a string of 'target add/target remove' uevents.

Based on a patch by Hannes Reinecke <hare@suse.de> this patch reworks
the target allocation code so that only uevents for existing targets
are sent. The sysfs registration is split off from the existing
scsi_target_alloc() into a in a new scsi_add_target() function, which
should be called whenever an existing target is found. Only then a
uevent is sent, so we'll be generating events for existing targets
only.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

It's big, but there doesn't seem to be a way to split it up smaller...
Signed-off-by: NTony Jones <tonyj@suse.de>
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The macro tells us whether the device is (or contains) an enclosure device.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This patch adds a new scsi_device flag (last_sector_bug) for devices
which contain a bug where the device crashes when the last sector is
read in a larger then 1 sector read.

This is for example the case with sdcards in the HP PSC1350 printer
cardreader and in the HP PSC1610 printer cardreader.
Signed-off-by: NHans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The current scsi_test_unit_ready() is updated to return sense code
information (in struct scsi_sense_hdr).  The sd and sr drivers are
changed to interpret the sense code return asc 0x3a as no media and
adjust the device status accordingly.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Some SCSI tape medium changers that need the BLIST_SINGLELUN flag have
the medium changer at one LUN and the tape drive at a different LUN.
The inquiry string of the tape drive may be different from that of the
medium changer.  In order for single_lun to be effective, every
scsi_device under a given scsi_target must have it set.  This means that
there needs to be a blacklist entry for BOTH the medium changer AND the
tape drive, which is impractical because some medium changers may be
paired with a variety of different tape drive models.  It makes more
sense to put the single_lun flag in scsi_target instead of scsi_device,
which causes every device at a given target ID to inherit the single_lun
flag from one LUN.  This makes it possible to blacklist just the medium
changer and not the tape drive.
Signed-off-by: NTony Battersby <tonyb@cybernetics.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The esp_reset_cleanup() function is called with the host lock held and
invokes starget_for_each_device() which wants to take it too.  Here is a
fix along the lines of shost_for_each_device()/__shost_for_each_device()
adding a __starget_for_each_device() counterpart which assumes the lock
has already been taken.

Eventually, I think the driver should get modified so that more work is
done as a softirq rather than in the interrupt context, but for now it
fixes a bug that causes the spinlock debugger to fire.

While at it, it fixes a small number of cosmetic problems with
starget_for_each_device() too.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Originally based on a patch by Kristen Carlson Accardi @ Intel.
Copious input from James Bottomley.
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Removes an obsolete method scsi_device_cancel which isn't being used
anywhere in the kernel.
Signed-off-by: NPriyanka Gupta <priyankag@google.com>
Acked-by: NGrant Grundler <grundler@parisc-linux.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When reporting SCSI devices to the SCSI midlayer, use the FCP LUN as
LUN reported to the SCSI layer. With this approach, zfcp does not have
to create unique LUNS, and this code can be removed.
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Signed-off-by: NSwen Schillig <swen@vnet.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The following patch adds support for sysfs/uevent modalias
attribute for scsi devices (like disks, tapes, cdroms etc),
based on whatever current sd.c, sr.c, st.c and osst.c drivers
supports.

The modalias format is like this:

 scsi:type-0x04

(for TYPE_WORM, handled by sr.c now).

Several comments.

o This hexadecimal type value is because all TYPE_XXX constants
  in include/scsi/scsi.h are given in hex, but __stringify() will
  not convert them to decimal (so it will NOT be scsi:type-4).
  Since it does not really matter in which format it is, while
  both modalias in module and modalias attribute match each other,
  I descided to go for that 0x%02x format (and added a comment in
  include/scsi/scsi.h to keep them that way), instead of changing
  them all to decimal.

o There was no .uevent routine for SCSI bus.  It might be a good
  idea to add some more ueven environment variables in there.

o osst.c driver handles tapes too, like st.c, but only SOME tapes.
  With this setup, hotplug scripts (or whatever is used by the
  user) will try to load both st and osst modules for all SCSI
  tapes found, because both modules have scsi:type-0x01 alias).
  It is not harmful, but one extra module is no good either.
  It is possible to solve this, by exporting more info in
  modalias attribute, including vendor and device identification
  strings, so that modalias becomes something like
    scsi:type-0x12:vendor-Adaptec LTD:device-OnStream Tape Drive
  and having that, match for all 3 attributes, not only device
  type.  But oh well, vendor and device strings may be large,
  and they do contain spaces and whatnot.
  So I left them for now, awaiting for comments first.
Signed-off-by: NMichael Tokarev <mjt@tls.msk.ru>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>