Remove some useless spaces (new line or space)
Reviewed-by: NJason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Add a return value check when reading data from the FIFO register.

Cc: <stable@vger.kernel.org>
Reviewed-by: NJason Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Detect TPM 2.0 by sending idempotent TPM 2.x command. Ordinals for
TPM 2.0 are higher than TPM 1.x commands so this should be fail-safe.
Using STS3 is unreliable because some chips just report 0xff and not
what the spec says.

Before TPM family is detected, timeouts are set to the maximum values
for both TPM 1.x and TPM 2.x. In addition to this, suspend/resume
functionality is implemented for TPM 2.x.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NWill Arthur <will.c.arthur@intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

tpm_crb is a driver for TPM 2.0 Command Response Buffer (CRB) Interface
as defined in PC Client Platform TPM Profile (PTP) Specification.

Only polling and single locality is supported as these are the limitations
of the available hardware, Platform Trust Techonlogy (PTT) in Haswell
CPUs.

The driver always applies CRB with ACPI start because PTT reports using
only ACPI start as start method but as a result of my testing it requires
also CRB start.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

TPM 2.0 devices are separated by adding a field 'flags' to struct
tpm_chip and defining a flag TPM_CHIP_FLAG_TPM2 for tagging them.

This patch adds the following internal functions:

- tpm2_get_random()
- tpm2_get_tpm_pt()
- tpm2_pcr_extend()
- tpm2_pcr_read()
- tpm2_startup()

Additionally, the following exported functions are implemented for
implementing TPM 2.0 device drivers:

- tpm2_do_selftest()
- tpm2_calc_ordinal_durations()
- tpm2_gen_interrupt()

The existing functions that are exported for the use for existing
subsystems have been changed to check the flags field in struct
tpm_chip and use appropriate TPM 2.0 counterpart if
TPM_CHIP_FLAG_TPM2 is est.

The code for tpm2_calc_ordinal_duration() and tpm2_startup() were
originally written by Will Arthur.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: NWill Arthur <will.c.arthur@intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>

[phuewe: Fixed copy paste error * 2]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Added own device class for TPM. Uses MISC_MAJOR:TPM_MINOR for the
first character device in order to retain backwards compatibility.
Added tpm_dev_release() back attached to the character device.

I've been running this code now for a while on my laptop (Lenovo
T430S) TrouSerS works perfectly without modifications. I don't
believe it breaks anything significantly.

The sysfs attributes that have been placed under the wrong place
and are against sysfs-rules.txt should be probably left to
stagnate under platform device directory and start defining
new sysfs attributes to the char device directory.

Guidelines for future TPM sysfs attributes should be probably
along the lines of

- Single flat set of mandatory sysfs attributes. For example,
  current PPI interface is way way too rich when you only want
  to use it to clear and activate the TPM.

- Define sysfs attribute if and only if there's no way to get
  the value from ring-3. No attributes for TPM properties. It's
  just unnecessary maintenance hurdle that we don't want.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NScot Doyle <lkml14@scotdoyle.com>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Rename chip->dev to chip->pdev to make it explicit that this not the
character device but actually represents the platform device.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Tested-by: NScot Doyle <lkml14@scotdoyle.com>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Traversal of the ACPI device tree was not done right. PPI interface
should be looked up only from the ACPI device that is the platform
device for the TPM. This could cause problems with systems with
two TPM chips such as 4th gen Intel systems.

In addition, added the missing license and copyright platter to
the tpm_ppi.c.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NScot Doyle <lkml14@scotdoyle.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

tpm_register_hardware() and tpm_remove_hardware() are called often
before initializing the device. The problem is that the device might
not be fully initialized when it comes visible to the user space.

This patch resolves the issue by diving initialization into two
parts:

- tpmm_chip_alloc() creates struct tpm_chip.

- tpm_chip_register() sets up the character device and sysfs
  attributes.

The framework takes care of freeing struct tpm_chip by using the devres
API. The broken release callback has been wiped. ACPI drivers do not
ever get this callback.

Regards to Jason Gunthorpe for carefully reviewing this part of the
code.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: NScot Doyle <lkml14@scotdoyle.com>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>
[phuewe: update to upstream changes]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Merged transmit_cmd() functions in tpm-interface.c and tpm-sysfs.c.
Added "tpm_" prefix for consistency sake. Changed cmd parameter as
opaque. This enables to use separate command structures for TPM1
and TPM2 commands in future. Loose coupling works fine here.
Signed-off-by: NJarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: NJasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: NStefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: NPeter Huewe <peterhuewe@gmx.de>
Tested-by: NScot Doyle <lkml14@scotdoyle.com>
Tested-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Added myself as a maintainer for the IBM vtpm driver and removed myself
from the tpm maintainer list. Also, updated the tpm_ibmvtpm driver with
my current email address.
Signed-off-by: NAshley Lai <ashleydlai@gmail.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

If !client the kernel mays oops in dev_info when doing client->dev.
Reported-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Many changes were added to the driver so increment the version.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Remove useless i2c read on TPM_INT_ENABLE and TPM_INT_STATUS
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Improve the irq management by using a new function wait_for_stat.
Instead of using a completion struct, we rely on the waitqueue read_queue
and int_queue from chip->vendor field.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Cleanup code indentation, braces, test variable when NULL.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

st33zp24 tpm can be seen as a trivial i2c device as other i2c tpm.
However several other properties needs to be documented such as lpcpd.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Add tpm_stm_st33_i2c dts structure keeping backward compatibility
with static platform_data support as well.
In the mean time to easy this update and to make it much simpler, we:
- Moved all gpio_request to devm_gpio_request_one primitive
- Moved request_irq to devm_request_irq
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

For sanity, replace every tpm_st33_* with tpm_stm_*
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Some functions return err, rc or ret for a status code.

Return ret instead for all of them.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

The serirq gpio pin is used only as interrupt. After driver initialization,
the serirq signal is always used through interrupt and never with gpio
kernel API.

The irq can then be initialized during the platform_data definition within the client->irq pin.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

In order to clean big buffers in st33zp24_platform_data structure,
replace with tpm_stm_dev for driver internal usage.
As only one buffer is really necessary replace with buf field.

In the mean time move tpm_i2c_stm_st33.h to include/linux/platform_data.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Move tpm registers to tpm_i2c_stm_st33.c.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Fix:
- WARNING: Missing a blank line after declarations
- WARNING: braces {} are not necessary for any arm of this statement
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

The Free Software Foundation may have mail address change.
In order to be sure to have up to date mail address give an url to
the license which includes accurate informations.
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

STMicroelectronics i2c tpm is the only one to have a different tristate
label.

Rename it "TPM Interface Specification 1.2 Interface (I2C - STMicroelectronics)"
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
[phuewe: corrected module name in the helptext]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

When sending data in tpm_stm_i2c_send, each loop iteration send buf.
Send buf + i instead as the goal of this for loop is to send a number
of byte from buf that fit in burstcnt. Once those byte are sent, we are
supposed to send the next ones.

The driver was working because the burstcount value returns always the maximum size for a TPM
command or response. (0x800 for a command and 0x400 for a response).

Cc: stable@vger.kernel.org
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NChristophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

The tpm_dev_vendor_release() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

sizeof(u8) is always 1.
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

There was an oops in tpm_ibmvtpm_get_desired_dma, which caused
kernel panic during boot when vTPM is enabled in Power partition
configured in AMS mode.

vio_bus_probe calls vio_cmo_bus_probe which calls
tpm_ibmvtpm_get_desired_dma to get the size needed for DMA allocation.
The problem is, vio_cmo_bus_probe is called before calling probe, which
for vtpm is tpm_ibmvtpm_probe and it's this function that initializes
and sets up vtpm's CRQ and gets required data values.  Therefore,
since this has not yet been done, NULL is returned in attempt to get
the size for DMA allocation.

We added a NULL check.  In addition, a default buffer size will
be set when NULL is returned.

Cc: <stable@vger.kernel.org>
Signed-off-by: NHon Ching (Vicky) Lo <honclo@linux.vnet.ibm.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Some machines, such as the Acer C720 and Toshiba CB35, have TPMs that do
not send IRQs while also having an ACPI TPM entry indicating that they
will be sent. These machines freeze on resume while the tpm_tis module
waits for an IRQ, eventually timing out.

When in interrupt mode, the tpm_tis module should receive an IRQ during
module init. Fall back to polling mode if none is received when expected.

Cc: <stable@vger.kernel.org>
Signed-off-by: NScot Doyle <lkml14@scotdoyle.com>
Tested-by: NMichael Mullin <masmullin@gmail.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: minor checkpatch fixed]
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Currently these driver are missing a check on the return value of devm_kzalloc,
which would cause a NULL pointer dereference in a OOM situation.

This patch adds a missing check for tpm_i2c_atmel.c and tpm_i2c_nuvoton.c

Cc: stable@vger.kernel.org
Signed-off-by: NKiran Padwal <kiran.padwal@smartplayin.com>
Reviewed-By: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Add newly registered TPMs to the tail of the list, not the beginning, so that
things that are specifying TPM_ANY_NUM don't find that the device they're
using has inadvertently changed.  Adding a second device would break IMA, for
instance.

Cc: stable@vger.kernel.org
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Reviewed-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: NPeter Huewe <peterhuewe@gmx.de>

Merge tag 'keys-next-fixes-20150114' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into next

Pull networking fixes from David Miller:

 1) Don't use uninitialized data in IPVS, from Dan Carpenter.

 2) conntrack race fixes from Pablo Neira Ayuso.

 3) Fix TX hangs with i40e, from Jesse Brandeburg.

 4) Fix budget return from poll calls in dnet and alx, from Eric
    Dumazet.

 5) Fix bugus "if (unlikely(x) < 0)" test in AF_PACKET, from Christoph
    Jaeger.

 6) Fix bug introduced by conversion to list_head in TIPC retransmit
    code, from Jon Paul Maloy.

 7) Don't use GFP_NOIO under spinlock in USB kaweth driver, from Alexey
    Khoroshilov.

 8) Fix bridge build with INET disabled, from Arnd Bergmann.

 9) Fix netlink array overrun for PROBE attributes in openvswitch, from
    Thomas Graf.

10) Don't hold spinlock across synchronize_irq() in tg3 driver, from
    Prashant Sreedharan.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
  tg3: Release tp->lock before invoking synchronize_irq()
  tg3: tg3_reset_task() needs to use rtnl_lock to synchronize
  tg3: tg3_timer() should grab tp->lock before checking for tp->irq_sync
  team: avoid possible underflow of count_pending value for notify_peers and mcast_rejoin
  openvswitch: packet messages need their own probe attribtue
  i40e: adds FCoE configure option
  cxgb4vf: Fix queue allocation for 40G adapter
  netdevice: Add missing parentheses in macro
  bridge: only provide proxy ARP when CONFIG_INET is enabled
  neighbour: fix base_reachable_time(_ms) not effective immediatly when changed
  net: fec: fix MDIO bus assignement for dual fec SoC's
  xen-netfront: use different locks for Rx and Tx stats
  drivers: net: cpsw: fix multicast flush in dual emac mode
  cxgb4vf: Initialize mdio_addr before using it
  net: Corrected the comment describing the ndo operations to reflect the actual prototype for couple of operations
  usb/kaweth: use GFP_ATOMIC under spin_lock in usb_start_wait_urb()
  MAINTAINERS: add me as ibmveth maintainer
  tipc: fix bug in broadcast retransmit code
  update ip-sysctl.txt documentation (v2)
  net/at91_ether: prepare and unprepare clock
  ...

Prashant Sreedharan says:

====================
tg3: synchronize_irq() should be called without taking locks

v2: Added Reported-by, Tested-by fields and reference to the thread that
    reported the problem

This series addresses the problem reported by Peter Hurley in mail thread
https://lkml.org/lkml/2015/1/12/1082
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

synchronize_irq() can sleep waiting, for pending IRQ handlers so driver
should release the tp->lock spin lock before invoking synchronize_irq()
Reported-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently tg3_reset_task() uses only tp->lock for synchronizing with code
paths like tg3_open() etc. But since tp->lock is released before doing
synchronize_irq(), rtnl_lock should be taken in tg3_reset_task() to
synchronize it with other code paths.
Reported-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid the race between tg3_timer() and the execution paths
which does not invoke tg3_timer_stop() and releases tp->lock before
calling synchronize_irq()
Reported-by: NPeter Hurley <peter@hurleysoftware.com>
Tested-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NPrashant Sreedharan <prashant@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull kvm fixes from Paolo Bonzini:
 "Two bugfixes for arm64.  I will have another pull request next week,
  but otherwise things are calm"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  arm64: KVM: Fix HCR setting for 32bit guests
  arm64: KVM: Fix TLB invalidation by IPA/VMID