[ralf@linux-mips.org: Original patch by Maxim Uvarov <muvarov@gmail.com>
with plenty of further shining, polishing, debugging and testing by me.]
Signed-off-by: NMaxim Uvarov <muvarov@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: kexec@lists.infradead.org
Cc: horms@verge.net.au
Patchwork: https://patchwork.linux-mips.org/patch/1026/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

No 32-bit kernels supported on Octeon.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Only supporting 64-bit kernels there is no point in depending on
this symbol.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

On Cavium hardware only 64-bit kernels are supported so CONFIG_HIGHMEM
is never set.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Drivers for EDAC on Cavium.  Supported subsystems are:

 o CPU primary caches.  These are parity protected only, so only error
   reporting.
 o Second level cache - ECC protected, provides SECDED.
 o Memory: ECC / SECDEC if used with suitable DRAM modules.  The driver will
   will only initialize if ECC is enabled on a system so is safe to run on
   non-ECC memory.
 o PCI: Parity error reporting

Since it is very hard to test this sort of code the implementation is very
conservative and uses polling where possible for now.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Reviewed-by: NBorislav Petkov <borislav.petkov@amd.com>

Also cleanup and fix octeon_init_cvmcount()
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

If a compiled in device tree template is used, trim out unwanted parts
based on legacy platform probing.
Signed-off-by: NDavid Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree-discuss@lists.ozlabs.org
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kernel@vger.kernel.org
Cc: David Daney <david.daney@cavium.com>
Patchwork: https://patchwork.linux-mips.org/patch/3935/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These will show up as a build failure once we clean up a
misuse of module.h in the mips termios header.

Uses export.h: (EXPORT_SYMBOL)
   arch/mips/cavium-octeon/setup.c
   arch/mips/pmc-sierra/yosemite/setup.c
   arch/mips/rb532/devices.c
   arch/mips/sni/setup.c

Uses module.h: (symbol_get/put)
   arch/mips/alchemy/devboards/db1200.c

Uses module.h: (print_modules)
   arch/mips/kernel/traps.c
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3448/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Disintegrate asm/system.h for MIPS.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
cc: linux-mips@linux-mips.org

This patch addresses a couple of related problems:

1) The kernel may reside in physical memory outside of the ranges set
   by plat_mem_setup().  If this is the case, init mem cannot be
   reused as it resides outside of the range of pages that the kernel
   memory allocators control.

2) initrd images might be loaded in physical memory outside of the
   ranges set by plat_mem_setup().  The memory likewise cannot be
   reused.  The patch doesn't handle this specific case, but the
   infrastructure is useful for future patches that do.

The crux of the problem is that there are memory regions that need be
memory_present(), but that cannot be free_bootmem() at the time of
arch_mem_init().  We create a new type of memory (BOOT_MEM_INIT_RAM)
for use with add_memory_region().  Then arch_mem_init() adds the init
mem with this type if the init mem is not already covered by existing
ranges.

When memory is being freed into the bootmem allocator, we skip the
BOOT_MEM_INIT_RAM ranges so they are not clobbered, but we do signal
them as memory_present().  This way when they are later freed, the
necessary memory manager structures have initialized and the Sparse
allocater is prevented from crashing.

The Octeon specific code that handled this case is removed, because
the new general purpose code handles the case.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1988/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n.  Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Octeon uses different interrupt irq for timer and performance counters.
Set CvmCtl[IPPCI] to correct irq value very early.
Signed-off-by: NChandrakala Chavva <cchavva@caviumnetworks.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/2085/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

This includes conversion to new style irq_chip functions, and
correctly enabling/disabling per-CPU interrupts.

The hardware interrupt bit to irq number mapping is now done with a
flexible map, instead of by bit twiddling the irq number.

[ tglx: Adjusted to new irq_cpu_on/offline callbacks and
        __irq_set_affinity_lock ]
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <1301081931-11240-5-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The CN63XXP1 needs a couple of workarounds to ensure memory is not written
in unexpected ways.

All PREF with hints in the range 0-4,6-24 are replaced with PREF 28.  We
pass a flag to the assembler to cover compiler generated code, and patch
uasm for the dynamically generated code.

The write buffer threshold is reduced to 4.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1672/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Starting with cn63xx Octeon I/O blocks are clocked at a different rate
than the CPU.  Add a new function octeon_get_io_clock_rate() that
yields the I/O clock rate.

Also rearrange octeon_get_clock_rate() to get the value from the saved
sysinfo structure.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1671/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We can run with any simulator clock rate.  Get rid of the code
overriding it to 6MHz.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1669/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We reserve the 3.75GB - 4GB region of PCIe address space for device to
device transfers, making the corresponding physical memory under
direct mapping unavailable for DMA.

To allow for PCIe DMA to all physical memory we map this chunk of
physical memory with BAR1.  Because of the resulting discontinuity in
the mapping function, we remove a page of memory at each end of the
range so multi-page DMA buffers can never be allocated that span the
range.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1535/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The forthcoming watchdog driver will use it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
To: wim@iguana.be
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1499/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Power throttling make deterministic delay loops impossible.
Re-implement delays using the cycle counter.  This also allows us to
get rid of the code that calculates loops per jiffy.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1317/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

CONFIG_GDB_CONSOLE doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
To: David Daney <ddaney@caviumnetworks.com>
To: Yang Shi <yang.shi@windriver.com>
To: Herbert Xu <herbert@gondor.apana.org.au>
To: Tejun Heo <tj@kernel.org>
To: linux-mips@linux-mips.org
To: linux-kernel@vger.kernel.org
Cc: vamos@i4.informatik.uni-erlangen.de
Patchwork: https://patchwork.linux-mips.org/patch/1368/Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For the simulator, fake a slow clock to get fast output.

In prom_putchar we have to mask the value so the simulator doesn't
ASSERT when printing non-ASCII characters.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1255/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Get rid of early_serial_setup, we use CONFIG_EARLY_PRINTK instead.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1254/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

octeon_reserve32_memory is defined In Octeon's setup.c, so remove the
redundant extern declaration of this variable.
Signed-off-by: NYang Shi <yang.shi@windriver.com>
To: f.fainelli@gmail.com
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1022/Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1029/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The config option CAVIUM_RESERVE32_USE_WIRED_TLB is not supported.
Remove the dead code controlled by it.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1028/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

There is a bunch of platform device registration in
arch/mips/cavium-octeon/setup.c.  We move it to its own file in
preparation for adding more platform devices.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a platform device for the Octeon Random Number Generator (RNG).
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Some of the were relying into smp.h being dragged in by another header
which of course is fragile.  <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

These are the rest of the new files needed to add OCTEON processor
support to the Linux kernel.  Other than Makefile and Kconfig which
should be obvious, we have:

csrc-octeon.c   -- Clock source driver for OCTEON.
dma-octeon.c    -- Helper functions for mapping DMA memory.
flash_setup.c   -- Register on-board flash with the MTD subsystem.
octeon-irq.c    -- OCTEON interrupt controller managment.
octeon-memcpy.S -- Optimized memcpy() implementation.
serial.c        -- Register 8250 platform driver and early console.
setup.c         -- Early architecture initialization.
smp.c           -- OCTEON SMP support.
octeon_switch.S -- Scheduler context switch for OCTEON.
c-octeon.c      -- OCTEON cache controller support.
cex-oct.S       -- OCTEON cache exception handler.

asm/mach-cavium-octeon/*.h -- Architecture include files.
Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com>
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/cavium-octeon/Kconfig
 create mode 100644 arch/mips/cavium-octeon/Makefile
 create mode 100644 arch/mips/cavium-octeon/csrc-octeon.c
 create mode 100644 arch/mips/cavium-octeon/dma-octeon.c
 create mode 100644 arch/mips/cavium-octeon/flash_setup.c
 create mode 100644 arch/mips/cavium-octeon/octeon-irq.c
 create mode 100644 arch/mips/cavium-octeon/octeon-memcpy.S
 create mode 100644 arch/mips/cavium-octeon/serial.c
 create mode 100644 arch/mips/cavium-octeon/setup.c
 create mode 100644 arch/mips/cavium-octeon/smp.c
 create mode 100644 arch/mips/include/asm/mach-cavium-octeon/cpu-feature-overrides.h
 create mode 100644 arch/mips/include/asm/mach-cavium-octeon/dma-coherence.h
 create mode 100644 arch/mips/include/asm/mach-cavium-octeon/irq.h
 create mode 100644 arch/mips/include/asm/mach-cavium-octeon/kernel-entry-init.h
 create mode 100644 arch/mips/include/asm/mach-cavium-octeon/war.h
 create mode 100644 arch/mips/include/asm/octeon/octeon.h
 create mode 100644 arch/mips/kernel/octeon_switch.S
 create mode 100644 arch/mips/mm/c-octeon.c
 create mode 100644 arch/mips/mm/cex-oct.S