The bttv card database structure had a "tuner" field that was the input
number of the tuner input or UNSET for no tuner.  However, the only values
it could ever be are 0 and UNSET.  Having a tuner on an input other than 0
didn't work and was never used.

There is also a "tuner_type" field that can be set to TUNER_ABSENT to
indicate no tuner, which makes "tuner = UNSET" redundant.  In many cases,
tuner_type was set to UNSET when there was no tuner, which isn't quite
correct.  tuner_type == UNSET is supposed to mean the tuner type isn't yet
known.

So, I changed cards where "tuner == UNSET" to always have tuner_type of
TUNER_ABSENT.  At this point the tuner field is redundant, so I deleted it.

I have the card setup code set the card's tuner_type (not the card type's
tuner_type!) to TUNER_ABSENT if it hasn't yet been set at the end of the
setup code.  Various places that check if the card has a tuner will now
look for this instead of checking the card type's "tuner" field.

Also autoload the tuner module before issuing the TUNER_SET_TYPE_ADDR I2C
client call instead of after issuing it.

Overall, on ia32 this decreases compiled code size by about 24 bytes and
reduces the data size by 640 bytes.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The code to set the norm for the TDA9880 analog demod was comparing
btv->norm, an index into the bttv driver's norm array, to V4L2_STD_NTSC,
which is a bit flag that's part of the V4L2 API.  This doesn't work of
course and results in the PAL path always being taken.

What's more, it modified the bttv_tvcards[] entries for cards using the
TDA9880.  This is wrong because changing the norm on one card will also
affect other cards of the same type.  Writing to bttv_tvcards is also bad
because it should be read-only or even devinitdata.

Changing the norm would also cause the audio to become unmuted.

Have the code get called for both norm setting and audio input setting
(which where the gpios are set) to avoid needed to modify bttv_tvcards.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The norm value in the driver is an index into an array and the the driver
doesn't allow it to be negative or otherwise invalid.  It should be
unsigned but wasn't in all places.

Fix some structs and functions to have the norm be unsigned.  Get rid of
useless checks for "< 0".  Most of the driver code can't handle a norm
value that's out of range, so change some ">= BTTV_TVNORMS" checks to
BUG_ON().  There's no point in silently ignoring invalid driver state just
to crash because of it later.
Reported-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added board Pinnacle Dazzle Video Creator Plus DVC107 to name description field.
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Coding style fixes for recent changesets in em28xx.
Signed-off-by: NNicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Control arrays as are used with v4l2_ctrl_next must be sorted from
low to high. Add a comment at the top of all such arrays to warn
about this.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

In order to convert the v4l1 zoran and vino i2c drivers to v4l2 these
extra ops are required.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The cx2341x_mpeg_ctrls array must be ordered by control ID. I know that
this is bad design, but for now I will just fix this bug and revisit it
when all drivers have moved to v4l2_device/v4l2_subdev, since that will
allow me to do greatly improve control handling.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

LED_REPORT and all flash REPORTs are on it's way. This code rearrangement
cleans up the code for proper integration later on.
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

- "DealExtreme" sells the "PCear" radio and that comes from "Sanei Electric".
- MPlayer is also usable as radio application.
- Consistent usage of tabulators and blanks in the code.
Signed-off-by: NTobias Lorenz <tobias.lorenz@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

[dougsland@redhat.com: Fixed CodingStyle]
Signed-off-by: NIndika Katugampala <indika_20012001@yahoo.co.jp>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Lots of coding style fixes and a typo correction for em28xx.

[dougsland@redhat.com: fixed a reject due to a change on em28xx-audio.c]
Signed-off-by: NNicola Soranzo <nsoranzo@tiscali.it>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added DVC 101 model to Pinnacle Dazzle description
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added macros EM28XX_START_AUDIO and EM28XX_STOP_AUDIO for em28xx_cmd().
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Patch removes printk and place em28xx_errdev macros to provide
information about driver name to dmesg.
Signed-off-by: NAlexey Klimov <klimov.linux@gmail.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added lock for users count
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Added spinlock for trigger session
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Essentially if a snd_em28xx_capture_trigger() stop followed by a snd_em28xx_capture_trigger() start would not yield any
data because there was some logic put in with an adev->shutdown variable which did not seem warranted in my humble opinion.
It would cause snd_em28xx_capture_trigger start never to start up the audio stream until the device was closed and
reopened again. Upon re-opening the device adev->shutdown is reset and audio data would again flow.
Signed-off-by: NRobert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix for em28xx memory leak and function rename
Signed-off-by: NRobert Krakora <rob.krakora@messagenetsystems.com>
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Removed bad check. Thanks to Robert Krakora <rob.krakora@messagenetsystems.com>
to report that.
Signed-off-by: NDouglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Kaiomy entry.

Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Thanks to Peter Senna Tschudin <peter.senna@gmail.com> for borrow me one
of those devices.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

For i2c normal work, we need to slow down the bus speed. However, the
slow down breaks the eeprom firmware load. So, use normal speed for
eeprom booting and then restore the i2c speed after that.

It should also be noticed that no other I2C transfer should be in course
while booting from eeprom, otherwise, tda10046 goes into an instable
state. So, proper locking are needed at the i2c bus master.

Tested with saa7134 MSI TV @nyware A/D board, that comes with an eeprom
with firmware version 29.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

KBL is not needed on saa7134, so, let's remove it.

However, we should take some care to avoid opening the module while
initializing it. This issue exists with newer udev's that opens a device
as soon as the driver is registered. So, a proper lock is needed on
open.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fix two broken controls where a step weren't specified. Without a step,
userspace apps won't allow to adjust such controls.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The waitqueue is never used. So, let's just remove it.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Some saa7134 devices require to open an i2c gate before tuning. This
patch fix the initialization for those devices.

The nxt200x_gate_ctrl() logic were returned back to the old place, since
we don't know how to close the gate. A future pacth could revert that
change and provide the proper close gate control, to avoid keeping it
open forever.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

On certain devices, before opening a tuner, we need to open the tuner
gate via i2c.

This patch just moves the tuner probing code to the same place where
such i2c commands are handled, to make easier to fix this trouble on
later patches.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

While here, be sure that gate will be kept disabled if an error occurs.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The gate control logic is broken: several routines just keep it open;
other rotines close it properly; there are even other routines that
assumes that it is open without really checking or opening it.

Instead of having to manually handle the gate control and having such
troubles, let a sub-routine take care of the gate, opening it before
i2c_transfer and closing it after that. This avoids leaving the gate
into a random state.

Cc: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Doing the v4l2_device registration in the saa7146 core will make it
dependent on v4l2, even for DVB-only boards. This registration and
unregistration belongs in saa7146_vv instead.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Modified mxb to load the i2c modules through v4l2_subdev. So no more probing.
Modified tea6415c and tea6420 to use the standard routing ops to do the
routing, rather than using private commands. Dropped the private commands
from tda9840 (they were never used except during initialization of the
module).

Added saa7146 support for VIDIOC_DBG_G_CHIP_IDENT.

Converted saa5246a and saa5249 to v4l2_subdev.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>