In the next patch, we will want to install a callback when the engines
(GT as a whole) become idle and similarly when they first become busy.
To enable that callback, first rename intel_engines_mark_idle() to
intel_engines_park() and provide the companion intel_engines_unpark().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171025143943.7661-2-chris@chris-wilson.co.uk

This is heavily based on a initial patch provided by Ville
plus all changes provided later by Ander.

As Geminilake, Cannonlake also supports 2 pixels per clock.

Different from Geminilake we are not implementing the 99% Wa.
But we can revisit that decision later if we find out
any limitation on later CNL SKUs.

v2: Rebase on top of commit 'd305e061 ("drm/i915: Track
minimum acceptable cdclk instead of "minimum dotclock")'

v3: When fixing HDMI on CNL I noticed that I missed to convert
    back the doubled pixel rate to cdclk.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171003223142.26264-1-rodrigo.vivi@intel.com

When running under virtualization (vGPU active), we must disable
the lazy PPGTT page table initialization optimization introduced by
commit 14826673 ("drm/i915: Only initialize partially filled
pagetables").

We must do this because GVT-g makes unduly assumptions about guest
behaviour, which this optimization breaks. This results in following
looking errors in the host:

ERROR gvt: guest page write error -22, gfn 0x7ada8, pa 0x7ada89a8, var 0x6, len 1

The real fix is to not to depend on i915 driver behaviour, but instead
either rely on only the contracts that i915 has with the hardware, or
add some paravirtualization. While the real fix is en route, it won't
be finished in time for 4.15, so the best option is to disable the
optimization for now when vGPU is active to avoid breaking 4.15 guests
in existing VM environments.

Fixes: 14826673 ("drm/i915: Only initialize partially filled pagetables")
Suggested-by: NXiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: NXiaolin Zhang <xiaolin.zhang@intel.com>
[Joonas: Rewrote the commit message and added tags.]
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Zhenyu Wang <zhenyuw@linux.intel.com>
Cc: Zhi Wang <zhi.a.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023153209.10527-1-joonas.lahtinen@linux.intel.com

This reverts commit 6d0dbd30.

timer_setup_on_stack() does not yet exist:

In file included from drivers/gpu/drm/i915/i915_sw_fence.c:517:0:
drivers/gpu/drm/i915/selftests/lib_sw_fence.c: In function ‘timed_fence_init’:
drivers/gpu/drm/i915/selftests/lib_sw_fence.c:63:2: error: implicit declaration of function ‘timer_setup_on_stack’; did you mean ‘hrtimer_init_on_stack’? [-Werror=implicit-function-declaration]
  timer_setup_on_stack(&tf->timer, timed_fence_wake, 0);
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171025131336.2584-1-chris@chris-wilson.co.ukAcked-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024151344.GA104417@beastReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

During evict, we wish to idle the GPU if we see that the GGTT is full.
However, our test for idle in i915_gem_evict_something() and in
i915_gem_switch_to_kernel_context() do not match leading to
disappointment - we never believe that we are idle and keep trying to
flush the GGTT ad infinitum.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=103438Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024220855.30155-2-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Instead of trying to create a timer with zero delay (i.e. with expires
set to the current jiffies and not the future, an already expired
timer), execute that request immediately.

v2: Refactor list_del_init+signal into its own little function.
v3: Reorder testing so as not to immediately signal a delayed request.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024220855.30155-1-chris@chris-wilson.co.uk
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

Insert a breakpoint, a chance to escape back to the scheduler and run
something else for a bit, if we find that the GGTT is full and needs to
be idled in order to make some room. In practice, this should only be an
issue in stress tests as the wait itself will normally give the chance
for the scheduler to intervene and make progress.

References: https://bugs.freedesktop.org/show_bug.cgi?id=103438Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024205053.7845-1-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

WARN if the cdclk state doesn't match what we expect after programming.
And let's remove the WARN from bdw_set_cdclk() that's trying to achieve
the same thing in a more limite fashion.

Also take the opportunity to refactor the code to use a common function
for dumping out a cdclk state.

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-11-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

chv_set_cdclk() sanity checks that the cdclk frequency is one of the
legal values. Do the same in the VLV function.

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-10-ville.syrjala@linux.intel.comReviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

On CNL we may need to bump up the system agent voltage not only due
to CDCLK but also when driving DDI port with a sufficiently high clock.
To that end start tracking the minimum acceptable voltage for each crtc.
We do the tracking via crtcs because we don't have any kind of encoder
state. Also there's no downside to doing it this way, and it matches how
we track cdclk requirements on account of pixel rate.

v2: Allow disabled crtcs to use the min voltage
    Add IS_CNL check to intel_ddi_compute_min_voltage() since
    we're using CNL specific values there
    s/intel_compute_min_voltage/cnl_compute_min_voltage/ since
    the function makes hw specific assumptions about the voltage
    values
v3: Drop the test hack leftovers from skl_modeset_calc_cdclk()
v4: s/voltage/voltage_level/ (Rodrigo)
    Replace DPLL DVFS FIXMEs with an explanation why we don't
    do anything there (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-9-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on CNL. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-8-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on BXT/GLK. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-7-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on SKL/KBL/CFL. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-6-ville.syrjala@linux.intel.com

Track the system agent voltage we request from pcode in the cdclk state
on BDW. Annoyingly we can't actually read out the current value since
there's no pcode command to do that, so we'll have to just assume that
it worked.

v2: Keep the WARN_ON (Rodrigo)
v3: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-5-ville.syrjala@linux.intel.com

Store the punit DSPFREQUAR value into cdclk_state->voltage on
VLV/CHV. Since we can actually read that out from the hardware
this can give us a bit more cross checking between the hardware
and software state.

v2: Don't break waiting for cdclk change on VLV/CHV
v3: Split out the cdclk sanity check in vlv_set_cdclk() (Rodrigo)
v4: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-4-ville.syrjala@linux.intel.com

For CNL we'll need to start considering the port clocks when we select
the voltage level for the system agent. To that end start tracking the
voltage in the cdclk state (since that already has to adjust it).

v2: s/voltage/voltage_level/ (Rodrigo)

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-3-ville.syrjala@linux.intel.com

Redo some switch statements in the cdclk code to use a common
fall through for the default case. Makes everything look a bit
more uniform

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024095216.1638-2-ville.syrjala@linux.intel.com

The latest version of DMC on CNL is 1.06.
Update the version so as to load the
latest firmware.

Release Notes:
Version: 1.06
1. DDI and AUX IO related fix.

v2: Improve the prefixes in commit message.
Add Release Notes directly. (Rodrigo)

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NAnusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507053588-677-1-git-send-email-anusha.srivatsa@intel.com

On CNL, individual wake rate limit was added to each engine.

GT can only go to RC6 if both Render and Media engines are
individually qualified. So we need to set their individual
wake rate limit.

+-----------------+---------------+--------------+--------------+
|                 |    GT RC6     |  Render C6   |   Media C6   |
+-----------------+---------------+--------------+--------------+
| Wake rate limit | 0xA09C[31:16] | 0xA09C[15:0] | 0xA0A0[15:0] |
+-----------------+---------------+--------------+--------------+

v2: - Tune Render and Media wake rate values according to some extra
      info I got from HW engineers. Value can be tuned, but for now
      these are the recommended values.
    - Fix typos pointed by James.

Cc: Nathan Ciobanu <nathan.d.ciobanu@intel.com>
Cc: Wayne Boyer <wayne.boyer@intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NJames Ausmus <james.ausmus@intel.com>
Reviewed-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023224612.27208-1-rodrigo.vivi@intel.com

As we faced in BXT, on CNL DDI_A_4_LANES is not
set as expected when system is boot with multiple
monitors connected. This result in wrong lane
setup impacting the max data rate available and
consequently blocking modeset on eDP, resulting
in a blank screen.

Most of CNL SKUs don't support DDI-E.
The only SKU that supports DDI-E is the same
that supports the full A/E split called DDI-F.

Also when DDI-F is used DDI-E cannot be used because
they share Interrupts. So DDI-E is almost useless.
Anyways let's consider this is possible and rely on
VBT for that.

This patch was initialy start by Clint, but required
many changes including full commit message. So
Credits entirely to Clint for finding this.

v2: Extract all messy conditions into a helper function
    as suggested by Ville.
    Along with simplification I removed the debug
    message on the working case since now all conditions
    are grouped.
v3: Split the conditions even more as suggested by Ville.
    Get's cleaner and easier to add new cases in the
    future.
Suggested-by: NClint Taylor <clinton.a.taylor@intel.com>
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023173920.22890-1-rodrigo.vivi@intel.com

The compat callback was missing and triggered failures in 32bits
userspace when enabling/disable the perf stream. We don't require any
particular processing here as these ioctls don't take any argument.
Signed-off-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Fixes: eec688e1 ("drm/i915: Add i915 perf infrastructure")
Cc: linux-stable <stable@vger.kernel.org>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024152728.4873-1-lionel.g.landwerlin@intel.com

Originally we set the priority to max upon inserting the request into
the execlists queue (and removing it from the scheduler lists). We could
then use the prio==INT_MAX as a shortcut within execlists_schedule() to
detect the end of the dependency chain. Since commit 1f181225
("drm/i915/execlists: Keep request->priority for its lifetime") this is
no longer true as we use the request completion as an indicator the
schedule dependency chain is complete instead. (This allows us to then
reschedule requests even when its context is in flight.) However, this
makes the GEM_BUG_ON() inside execlists_schedule() racy as we may change
the rq->prio at the same time. As the assertion is useful, let's keep
the assertion and remove the micro-optimisation.

Fixes: 1f181225 ("drm/i915/execlists: Keep request->priority for its lifetime")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171024115501.21033-1-chris@chris-wilson.co.ukReviewed-by: NMichał Winiarski <michal.winiarski@intel.com>

Back in commit a4b2b015 ("drm/i915: Don't mark an execlists
context-switch when idle") we noticed the presence of late
context-switch interrupts. We were able to filter those out by looking
at whether the ELSP remained active, but in commit beecec90
("drm/i915/execlists: Preemption!") that became problematic as we now
anticipate receiving a context-switch event for preemption while ELSP
may be empty. To restore the spurious interrupt suppression, add a
counter for the expected number of pending context-switches and skip if
we do not need to handle this interrupt to make forward progress.

v2: Don't forget to switch on for preempt.
v3: Reduce the counter to a on/off boolean tracker. Declare the HW as
active when we first submit, and idle after the final completion event
(with which we confirm the HW says it is idle), and track each source
of activity separately. With a finite number of sources, it should aide
us in debugging which gets stuck.

Fixes: beecec90 ("drm/i915/execlists: Preemption!")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Michal Winiarski <michal.winiarski@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Arkadiusz Hiler <arkadiusz.hiler@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-3-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

When we park the engine (upon idling), we kill the irq tasklet. However,
to be sure that it is not restarted by a spurious interrupt after doing so,
flush the interrupt handler before parking. As we only park the engines
when we believe the system is idle, there should not be any interrupts to
distrub us; so flushing the final in-flight interrupt should be sufficient.
(However, we are still dependent on the HW behaving in an orderly and
timely fashion, which we shall endeavour to improve upon later.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-2-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>

In the idle worker we drop the prolonged GT wakeref used to cover such
essentials as interrupt delivery. (When a CS interrupt arrives, we also
assert that the GT is awake.) However, it turns out that 10ms is not
long enough to be assured that the last CS interrupt has been delivered,
so bump that to 200ms, and move the entirety of that wait to before we
take the struct_mutex to avoid blocking. As this is now a potentially
long wait, restore the earlier behaviour of bailing out early when a new
request arrives.

v2: Break out the repeated check for new requests into its own little
helper to try and improve the self-commentary.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171023213237.26536-1-chris@chris-wilson.co.uk

Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Starting on CNL we now need to map VBT DDC Pin to
BSPec DDC Pin values. Not a direct translation anymore.

According to VBT
Block 2 (General Bytes Definition)
DDC Bus

+----------+-----------+--------------------+
| DDI Type | VBT Value | Bspec Mapped Value |
+----------+-----------+--------------------+
| DDI-B    | 0x1       | 0x1                |
| DDI-C    | 0x2       | 0x2                |
| DDI-D    | 0x3       | 0x4                |
| DDI-F    | 0x4       | 0x3                |
+----------+-----------+--------------------+

v2: Move defines to a better place.
    This is actually CNL_PCH not CNL only.
v3: Accepting Ville's suggestions: enums and array to
    to make this future proof.
v4: Protect the array access as Ville suggested.
    Also accepting all Jani's suggestions:
    	      - use already defined gmbus pin definitions.
	      - use map_ddc_pin for disambiguation.
	      - Add /* sic */ comment on inverted values
	      	so people can easily see it it nos a mistake
		we have the map 3 -> 4 and 4 -> 3 :/

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Clinton Taylor <clinton.a.taylor@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171020172641.16029-1-rodrigo.vivi@intel.com

No functional change expected. Just let's use this enum
when possible and also same standard pll_id name
so we can rework gen9+ port clock later.

Cc: Mika Kahola <mika.kahola@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018195407.8618-1-rodrigo.vivi@intel.com

This patch re-use already parsed DSI backlight/cabc ports
info for saving it inside struct intel_dsi rather than
parsing it at the time of DSI initialization.

V2: Remove backlight and cabc variable initialization (Jani N).
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507898700-20016-2-git-send-email-madhav.chauhan@intel.com

This patch parse DSI backlight/cabc ports info from
VBT and save them inside local structure. This saved info
can be directly used while initializing DSI for different
platforms instead of parsing for each platform.

V2: Changes:
    - Typo fix in commit message.
    - Move up newly added port variables (Jani N)
    - Remove redundant initialization (Jani N)
    - Don't parse CABC ports if not supported (Jani N)
V3: Patch restructure (Suggested by Jani N)

Credits-to: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NMadhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1507898700-20016-1-git-send-email-madhav.chauhan@intel.com

If the device is in runtime suspend, resuming takes time and reduces our
powersaving. If this was for a small write into an object, that resume
will take longer than any savings in using the indirect GGTT access to
avoid the cpu cache.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20171019063733.31620-1-chris@chris-wilson.co.uk

Only the DDI hook has some actual content.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017140313.20937-1-jani.nikula@intel.com

They're unused and unsupported. Leave the reduced_clock pointers in
place still, should they prove useful later on.

v2: go from nuking DDI lowfreq_avail to nuking it entirely (Ville)

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171017140234.20677-1-jani.nikula@intel.com

A bunch of functions are now exclusively used for HDMI, so naming the
variables with hdmi prefix/suffix is redundant. Also use int rather
than u32 for the translation level consistently.

v2: Rebase due to hdmi_level=-1 avoidance

Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181958.4423-1-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Handle missing buf trans tables, or out of bounds buf trans levels
the same way everywhere. These should never be hit under normal
conditions, but let's play it safe for now.

v2: Avoid the hdmi_level=-1 case (James)

Cc: James Ausmus <james.ausmus@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171018181934.4229-1-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

SKL DDI B/C/D only have 9 usable buf trans registers for DP/eDP. That
matches the normal DP buf trans tables, but the low vswing eDP tables
have 10 entries. Thus the eDP tables can only be used safely with DDI A
and E.

We try to catch cases where DDI B/C/D gets used with the wrong number of
entires in some parts of the code, but not everywhere. Let's move the
code to deal with that deeper into intel_ddi_get_buf_trans_edp(). And
for sake of symmetry do the same in intel_ddi_get_buf_trans_dp(). That
would also avoid explosions in the rather unlikely case that the DP
tables would get revised to 10 entries as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-9-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

default_index contained in the BXT buf_trans tables is actually useless.
For DP we should always have a valid level selected (otherwise the link
training logic would be buggy), and for HDMI we can just do what the
other platforms do and pick the correct entry in intel_ddi_hdmi_level().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-8-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

encoder->type is unreliable for DP/HDMI, so pass it in explicity into
cnl_ddi_vswing_sequence(). This matches what we do for BXT.

v2: Pass intel_encoder down to cnl_ddi_vswing_program(), and
    clean up the argument types while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-7-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>

Make BXT less special by following the CNL approach and handling
it in intel_ddi_dp_voltage_max() alognside every other DDI platform.

v2: Clean up the argument types to bxt_ddi_vswing_sequence() while at it
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171016145705.11780-6-ville.syrjala@linux.intel.comReviewed-by: NJames Ausmus <james.ausmus@intel.com>