Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
CC: Guennadi Liakhovetski <kernel@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Lacy <mauro@lacy.com.ar>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled

CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN

It has an audio connector coming out from a chip labeled

ATMEL
0242
AT89C2051-24PI

It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)

...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
        Subsystem: 008a:763c
        Flags: bus master, medium devsel, latency 64, IRQ 58
        Memory at dfffe000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2

01:0a.1 0480: 109e:0878 (rev 11)
        Subsystem: 008a:763c
        Flags: bus master, medium devsel, latency 64, IRQ 58
        Memory at dffff000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2

It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.

Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: NErnesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

poll_one allocated on stack struct poll_wqueues which is pretty big
structure (>500 bytes on x86_64). v4l1_compat_sync invokes poll_one
in a loop, so allocate struct poll_wqueues in v4l1_compat_sync (with
kmalloc) and pass it to poll_one.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

v4l_compat_translate_ioctl used 1376 bytes of stack (x86_64),
so split this 800 lines long function into ~20 small noinline functions;
the biggest function takes now 712 bytes (v4l1_compat_sync)

fix VIDIOCSWIN handler which printked wrong errors
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

fix most coding style violations found by checkpatch
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

simple_dvb_configure returns the actual tuned frequency to its caller, so
it must be declared as a u32 rather than an int.  As a result, we will
return 0 to indicate a failure.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

taken from dvb-pll
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

if (priv->i2c_props.adap == NULL) then exit any function that would
send commands over the i2c bus.  We allow drivers to attach without an
i2c adapter for cases where the dvb demod accesses the tuner directly
via calc_regs.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add entry points used for digital tuning via the dvb_frontend.

Share state data between multiple instances of the driver for hybrid
tuners.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Convert tda9887 to use the new hybrid_tuner_request_state and
hybrid_tuner_release_state macros to manage state sharing between
hybrid tuner instances.

Some ATSC/DVB cards need to put the analog demodulator into standby
before tuning digital.  This patch allows us to attach the tda9887
driver to the digital side of the bridge driver and be able to put
it into standby without jeopardizing the analog demod driver's state.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The 6.5 MHz carrier was interpreted as SECAM-L even if SECAM-D/K was
selected.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fsc 3.58 refers to Combination PAL-N (aka PAL-Nc), not to plain PAL-N (that
uses Fsc 4.43).
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are two tuner types: those for M/N standards and those for all others.
However, M/N standards are not always 60 Hz (PAL-N/Nc are 50 Hz), so rename
the module option accordingly.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allow options like pal=bgh, improve description of those options.
Add tunerhz option: 50=card has 50Hz tuner, 60=card has 60Hz tuner.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The q_io queue was never taken into account by the poll function. Thanks to
Andy Walls for finding this bug.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Improve hardware parameter negotiation between the camera host driver and
camera drivers. Parameters like horizontal and vertical synchronisation,
pixel clock polarity shall be set depending on capabilities of the
parties.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Please run checkpatch prior to sending patches
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This saves an initialization and a comparison.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NSascha Sommer <saschasommer@freenet.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Previously, the macro DVR_FEED, which is used to recognize and filter
out duplicate packets going to the DVR device, used the TS_PAYLOAD_ONLY
flag to identify a packet's destination.

This kind of filtering was introduced by the following two changesets:

Now, that it is possible to record TS PIDs using the demux device by
setting the output type to DMX_OUT_TSDEMUX_TAP, checking TS_PAYLOAD_ONLY
is not sufficient anymore. Therefore another flag, TS_DEMUX, is added to
specify the output type of a feed.

This allows multiple clients to filter the same TS PID on a demux device
simultaneously.
Signed-off-by: NAndreas Oberritter <obi@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix a cut-and-paste error
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If dvb_attach fails, dev->dvb.frontend is NULL. This will produce an OOPS, as
reported.

Thanks to Vanessa Ezekowitz <vanessaezekowitz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The pvrusb2 driver normally picks up the default video standard from the
eeprom on Hauppauge devices, but the OnAir HDTV and OnAir Creator are not
Hauppauge devices, and do not store this information in any eeprom.

These devices support NTSC/ATSC, so we should use NTSC by default when in
analog mode.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This change significantly rearranges pvr2_context level initialization
and operation:

1. A new kernel thread is set up for management of the context.

2. Destruction of the pvr2_context instance is moved into the kernel
   thread.  No other context is able to remove the instance; doing
   this simplifies lock handling.

3. The callback into pvrusb2-main, which is used to trigger
   initialization of each interface, is now issued from this kernel
   thread.  Previously it had been indirectly issued out of the work
   queue thread in pvr2_hdw, which led to deadlock issues if the
   interface needed to change a control setting (which in turn
   requires dispatch of another work queue entry).

4. Callbacks into the interfaces (via the pvr2_channel structure) are
   now issued strictly from this thread.  The net result of this is
   that such callback functions can now also safely operate driver
   controls without deadlocking the work queue.  (At the moment this
   is not actually a problem, but I'm anticipating issues with this in
   the future).

5. There is no longer any need for anyone to enter / exit the
   pvr2_context structure.  Implementation of the kernel thread here
   allows this all to be internal now, simplifying other logic.

6. A very very longstanding issue involving a mutex deadlock between
   the pvrusb2 driver and v4l should now be solved.  The deadlock
   involved the pvr2_context mutex and a globals-protecting mutex in
   v4l.  During initialization the driver would take the pvr2_context
   mutex first then the v4l2 interface would register with v4l and
   implicitly take the v4l mutex.  Later when v4l would call back into
   the driver, the two mutexes could possibly be taken in the opposite
   order, a situation that can lead to deadlock.  In practice this
   really wasn't an issue unless a v4l app tried to start VERY early
   after the driver appeared.  However it still needed to be solved,
   and with the use of the kernel thread relieving need for
   pvr2_context mutex, the problem should be finally solved.
Signed-off-by: NMike Isely <isely@pobox.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>