Use spin_lock_irqsave instead of spin_lock in ax_interrupt because
the interrupt handler can also be invoked from ei_watchdog.
Signed-off-by: NKen Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based upon a report by Randy Dunlap.

DSA needs PHYLIB, but PHYLIB needs NET_ETHERNET.  So, in order
to select PHYLIB we have to make DSA depend upon NET_ETHERNET.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

not all of the ICMP packets need an IP header payload, so we check the length
of the skbs only when the packets should have an IP header payload.

Based upon analysis and initial patch by Rodrigo Partearroyo González.
Signed-off-by: NChangli Gao <xiaosuo@gmail.com>
Acked-by: NHerbert Xu <herbert@gondor.apana.org.au>
----
 net/sched/act_nat.c |    5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge error.

See CFG_METHOD_8 (0x3c800000 + 0x00300000) since version 8.002.00
of Realtek's driver.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Hayes <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update auth level for already existing connections if it is lower
than required by new connection.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Reviewed-by: NEmeltchenko Andrei <andrei.emeltchenko@nokia.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When authentication fails for a connection the assumed security level
should be set back to BT_SECURITY_LOW so that subsequent connect
attempts over the same link don't falsely assume that security is
adequate enough.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Due to race condition in L2CAP state machine L2CAP Connection Request
may be sent twice for SDP with the same source channel id. Problems
reported connecting to Apple products, some carkit, Blackberry phones.

...
2010-06-07 21:18:03.651031 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
2010-06-07 21:18:03.653473 > HCI Event: Number of Completed Packets (0x13) plen 5
    handle 1 packets 1
2010-06-07 21:18:03.653808 > HCI Event: Auth Complete (0x06) plen 3
    status 0x00 handle 1
2010-06-07 21:18:03.653869 < ACL data: handle 1 flags 0x02 dlen 12
    L2CAP(s): Connect req: psm 1 scid 0x0040
...

Patch uses L2CAP_CONF_CONNECT_PEND flag to mark that L2CAP Connection
Request has been sent already.

Modified version of patch from Ville Tervo.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 drivers/net/sb1250-mac.c |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original KERN_CRIT will mess up terminals.

CC: Sreenivasa Honnur <Sreenivasa.Honnur@neterion.com>
Signed-off-by: NWu Fengguang <fengguang.wu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix missing iounmaps.
Signed-off-by: NDenis Kirjanov <dkirjanov@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bridge protocol lives dangerously by having incestuous relations
with the IP stack.  In this instance an abomination has been created
where a bogus IPCB area from a bridged packet leads to a crash in
the IP stack because it's interpreted as IP options.

This patch papers over the problem by clearing the IPCB area in that
particular spot.  To fix this properly we'd also need to parse any
IP options if present but I'm way too lazy for that.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Cheers,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Failure cases within ath9k_hif_usb_alloc_urbs are failed
to release allocated memory.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On Tue, Jul 06, 2010 at 08:48:35AM +0800, Herbert Xu wrote:
>
> bridge: Restore NULL check in br_mdb_ip_get

Resend with proper attribution.

bridge: Restore NULL check in br_mdb_ip_get

Somewhere along the line the NULL check in br_mdb_ip_get went
AWOL, causing crashes when we receive an IGMP packet with no
multicast table allocated.

This patch restores it and ensures all br_mdb_*_get functions
use it.
Reported-by: NFrank Arnold <frank.arnold@amd.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netif_vdbg() was originally defined as entirely equivalent to
netdev_vdbg(), but I assume that it was intended to take the same
parameters as netif_dbg() etc.  (Currently it is only used by the
sfc driver, in which I worked on that assumption.)

In commit a4ed89cb I changed the definition used when VERBOSE_DEBUG is
not defined, but I failed to notice that the definition used when
VERBOSE_DEBUG is defined was also not as I expected.  Change that to
match netif_dbg() as well.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net_device allocated with alloc_eip_netdev() must be freed.
Signed-off-by: NKulikov Vasiliy <segooon@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While using xfrm by MARK feature in
2.6.34 - 2.6.35 kernels, the mark
is always cleared in flowi structure via memset in
_decode_session4 (net/ipv4/xfrm4_policy.c), so
the policy lookup fails.
IPv6 code is affected by this bug too.
Signed-off-by: NPeter Kosyh <p.kosyh@gmail.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

virtio net will never try to overflow the TX ring, so the only reason
add_buf may fail is out of memory. Thus, we can not stop the
device until some request completes - there's no guarantee anything
at all is outstanding.

Make the error message clearer as well: error here does not
indicate queue full.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (...and avoid TX_BUSY)
Cc: stable@kernel.org  # .34.x (s/virtqueue_/vi->svq->vq_ops->/)
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently fill all of RX ring, then add_buf
returns ENOSPC, which gets mis-detected as an out of
memory condition and causes us to reschedule the work,
and so on forever. Fix this by oom = err == -ENOMEM;
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: stable@kernel.org # .34.x
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch resolves a number of issues in the statistics gathering of
the s2io driver.

On Xframe adapters, the received multicast statistics counter includes
pause frames which are not indicated to the driver.  This can cause
issues where the multicast packet count is higher than what has actually
been received, possibly higher than the number of packets received.

The driver software counters are replaced with the adapter hardware
statistics for rx_packets, rx_bytes, and tx_bytes.  It also uses the
overflow registers to determine if the statistics wrapped the 32bit
register (removing the window of having a statistic value less than the
previous call).  rx_length_errors statistic now includes undersized
packets in addition to oversized packets in its counting.  Finally,
rx_crc_errors are now being counted.
Signed-off-by: NJon Mason <jon.mason@exar.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix kernel-doc warnings in linux/net.h:

Warning(include/linux/net.h:151): No description found for parameter 'wq'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'fasync_list' description in 'socket'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'wait' description in 'socket'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.

The flow for this is,

dev_queue_xmit()
	dev_pick_tx()
		skb_tx_hash()  => hash using real_num_tx_queues
		skb_set_queue_mapping()
	...
	qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
	dev_hard_start_xmit()
		ndo_start_xmit(skb,dev) => skb queue set with old hash

skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues.  When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.

This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calling qdisc_reset() the qdisc lock needs to be held.  In
this case there is at least one driver i4l which is using this
without holding the lock.  Add the locking here.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some ocasions the function qlge_io_resume() tries to add a
pending timer, which causes the system to hit the BUG() on
add_timer() function.

This patch removes the timer during the EEH recovery.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently qlge driver calls add_timer() instead of mod_timer().
This patch changes add_timer() to mod_timer(), which seems a better
solution.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NRon Mercer <ron.mercer@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_printk() follows the net_device's parent device pointer, so
we must set that earlier than we previously did.
Reported-by: NLuís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit c17b274d.

That change was reported to break rndis_wlan support for the WUSB54GS.
Reported-by: NLuís Picciochi Oliveira <pitxyoki@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a firmware error or the firmware is reloaded for some other
reason we currently clear all station information, including keys
associated with them. A problem is that we do not clear some other
information regarding keys that are not stored in the station structs.

The consequence of this is that when the device is reconfigured after the
firmware reload we can, among other things, run out of key indices.

This fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16232
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2221Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>

We should release dst if dst->error is set.

Bug introduced in 2.6.14 by commit e104411b
([XFRM]: Always release dst_entry on error in xfrm_lookup)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NPatrick McHardy <kaber@trash.net>

Fixed include error, changed to linux/io.h
Signed-off-by: NCody Rester <codyrester@gmail.com>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

patch 'break out of polling loop on error' caused
a minor performance regression on my machine: recover
that performance by adding a bunch of unlikely annotations
in the error handling.
Signed-off-by: NMichael S. Tsirkin <mst@redhat.com>

When two systems using bonding devices in adaptive load
balancing (ALB) communicates with each other, an endless
ping-pong of ARP replies starts between these two systems.

What happens? In the ALB mode, bonding driver keeps track
of each client connected in a hash table, so it can do the
receive load balancing (RLB). This hash table is updated
when an ARP reply is received, then it scans for the client
entry, updates its MAC address and flag it to be announced
later. Therefore, two seconds later, the alb monitor runs
and send for each updated client entry two ARP replies
updating this specific client. The same process happens on
the receiving system, causing the endless ping-pong of arp
replies.

See more information including the relevant functions below:

   System 1                          System 2
    bond0                             bond0

   ping <system2>
    ARP request  --------->
                           <--------- ARP reply

+->rlb_arp_recv  <---------------------+   <--- loop begins
|  rlb_update_entry_from_arp           |
|  client_info->ntt = 1;               |
|  bond_info->rx_ntt = 1;              |
|                                      |
|         <communication succeed>      |
|                                      |
|  bond_alb_monitor                    |
|  rlb_update_rx_clients               |
|  rlb_update_client                   |
|  arp_create(ARPOP_REPLY)             |
|   send ARP reply -------------->     V
|   send ARP reply -------------->
|                               rlb_arp_recv
|                               rlb_update_entry_from_arp
|                               client_info->ntt = 1;
|                               bond_info->rx_ntt = 1;
|                           < snipped, same as in system 1>
+-------           <-------------- send ARP reply
                   <-------------- send ARP reply

Besides the unneeded networking traffic, this loop breaks
a cluster because a backup system can't take over the IP
address. There is always one system sending an ARP reply
poisoning the network.

This patch fixes the problem adding a check for the MAC
address before updating it. Thus, if the MAC address didn't
change, there is no need to update neither to announce it later.
Signed-off-by: NFlavio Leitner <fleitner@redhat.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix abuse of the preincrement operator as detected when building with gcc
4.6.0:

	 CC [M]  drivers/bluetooth/hci_bcsp.o
	drivers/bluetooth/hci_bcsp.c: In function 'bcsp_prepare_pkt':
	drivers/bluetooth/hci_bcsp.c:247:20: warning: operation on 'bcsp->msgq_txseq' may be undefined
Reported-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Acked-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Acked-by: NLennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Determine the size of the xfrm_mark struct, not of its pointer.
Signed-off-by: NAndreas Steffen <andreas.steffen@strongswan.org>
Acked-by: NJamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In driver ixgbe, ixgbe_atr may cause crashes for non-ipv4 packets. Just
add a test to check skb->protocol.  It may crash on short packets due
to ip_hdr() access.
Signed-off-by: NGuillaume Gaudonville <guillaume.gaudonville@6wind.com>
Acked-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>