It is quite common to have omapfb probe deferred because of a missing
resource, and to get omapfb probed succesfully a bit later. This works
fine. However, omapfb does not give any print on a successful probe, so
if the omapfb is actually never probed again after deferral, this is not
shown in the log.

To help debugging, add a simple print from omapfb at the end of its
probe, saying which display it is using and in which resolution.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The HDMI driver tries to get the needed memory resources by name and by
ID. Resources by name are not currently defined, and will be used with
DT boot.

The resource names used in the driver are not quite perfect, and as they
are not used yet, we can change them. This patch removes the unneeded
"hdmi_" prefix from the names, and simplifies the names (e.g. hdmi_txphy
-> phy).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI contains three separate blocks: protocol engine, PHY and PLL. At the
moment, all these are memory mapped in one big chunk. We need to split
that memory map into smaller pieces so that we can add proper 'reg'
properties into the DT data for each block.

This patch changes the driver to map the blocks separately. It first
tries to get the memory resource using name, used when booting with DT,
and if that fails, it gets the memory resource by ID, in which case the
driver gets the big chunk from platform data. That big chunk is then
split into the smaller blocks manually.

After DSS DT code has been merged and the old platform code removed, we
can clean up the memory resource management.

Instead of changing the driver in all the places where a register is
read or written, this patch takes a shortcut: it adds an additional
number to the struct which represents the register index. This number is
used to decide which base address to use. In the future we should
consider other approaches.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI_IRQ_CORE was not defined in the hdmi.h.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

HDMI_WP_CLK was wrongly defined as HDMI_WP_WP_CLK. Fix that.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

hdmi_wait_for_bit_change() has two issues:

The register index was passed as u16, even if the register index may be
u32. Fix the index to u32.

The function was copied from wait_for_bit_change() which waits for a
single bit to change, but the hdmi version was changed to wait for a bit
field. This change was not done correctly.

The function is supposed to return the (last) value of the bit field,
but it returned !val in case of timeout. This was correct for the single
bit version, but not for the hdmi version. Fix the function to return
the actual value in the register.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DISPC_MSTANDBY_CTRL register is used in the driver, but it's not
restored in dispc_restore_context(), causing problems after resume.

Instead of adding DISPC_MSTANDBY_CTRL to dispc_restore_context(), let's
call _omap_dispc_initial_config() as the first thing in
dispc_runtime_resume(). This will initialize the DISPC core registers
properly, and will avoid similar issues in the future.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

For some reason the hdmi driver first turns off the video output when
it's about to enable the video output. This serves no purpose, and can
be removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The hdmi4 driver currently rejects any timing which is not from the CEA or VESA
standards. This leads hdmi rejecting any non-standard mode. A non standard
timing may not have a valid code corresponding to it. In such cases, the HDMI
spec suggests to set the code to 0.

Modify the driver to check if the timings fall within the range of the DISPC
TV overlay manager, and remove the check for an invalid code. Add a debug print
specifying the mode and code in hdmi_display_set_timing.
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

DSI has separate TX and RX fifos. However, the current code only has one
field where the fifo size is stored, and the code for both TX and RX
config write to the same field. This has not caused issues, as we've
been using the same fifo sizes.

Fix this bug by creating separate fields for TX and RX fifo sizes.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

omapdss in compat mode creates some sysfs files into the device's sysfs
directory, including a 'name' file. This works fine for
platform_devices, but breaks with i2c or spi devices, as those already
have a 'name' file.

Fix this by renaming the omapdss's 'name' file to 'display_name'.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

OMAP5 has MFLAG feature in DISPC. Add the register definition and dump
it. The register is not used yet, though.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

When omapfb does ovl->get_overlay_info, ovl->set_overlay_info, the set
function may fail even if the info has not been changed. This is because
omapdss doesn't initialize the info, but expect the caller to set valid
values.

Normally that is the case, but there is at least one corner case: if
omapfb has not allocated memory for the overlay yet, and the user uses
ioctl to disable the overlay to make sure it's disabled. In this case
get_overlay_info returns invalid data, but the user is only interested
in setting the overlay to disabled, not configuring it, and
set_overlay_info fails.

The issue is made possible by the omapfb's setup_plane ioctl, which
groups overlay configuration and overlay enable/disable bit into the
same struct. Thus, when you are disabling an overlay, you are also
configuring it.

This is a bit counter intuitive, so I think it's better to initialize
the info to some valid values.

The fields requiring initialization are color_mode and rotation_type,
and also we need to remove the check for (paddr == 0), as paddr is 0 for
unallocated overlay (but it's still fine to disable the overlay).
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Fix debug prints all over omapdss:
* add missing linefeeds
* change pr_err/pr_debug to DSSERR/DSSDBG
* add missing DSS_SUBSYS_NAMEs
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Functions dispc_ovl_set_fifo_threshold and
dispc_ovl_compute_fifo_thresholds need to be exported. Add the
EXPORT_SYMBOLs.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Pull ARM SoC fixes from Olof Johansson:
 "Another smallish batch of fixes, it's been quiet due to the holidays.
  Nothing controversial here, a handful of things across the board"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: pxa: fix USB gadget driver compilation regression
  ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
  ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
  ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
  ARM: shmobile: r8a7790: fix shdi resource sizes
  ARM: shmobile: bockw: fixup DMA mask
  ARM: shmobile: armadillo: Add PWM backlight power supply

Pull x86 fixes from Peter Anvin:
 "There is a small EFI fix and a big power regression fix in this batch.

  My queue also had a fix for downing a CPU when there are insufficient
  number of IRQ vectors available, but I'm holding that one for now due
  to recent bug reports"

* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  x86/efi: Don't select EFI from certain special ACPI drivers
  x86 idle: Repair large-server 50-watt idle-power regression

Pull ACPI and power management fixes and new device IDs from Rafael Wysocki:

 - Fix for a cpufreq regression causing stale sysfs files to be left
   behind during system resume if cpufreq_add_dev() fails for one or
   more CPUs from Viresh Kumar.

 - Fix for a bug in cpufreq causing CONFIG_CPU_FREQ_DEFAULT_* to be
   ignored when the intel_pstate driver is used from Jason Baron.

 - System suspend fix for a memory leak in pm_vt_switch_unregister()
   that forgot to release objects after removing them from
   pm_vt_switch_list.  From Masami Ichikawa.

 - Intel Valley View device ID and energy unit encoding update for the
   (recently added) Intel RAPL (Running Average Power Limit) driver from
   Jacob Pan.

 - Intel Bay Trail SoC GPIO and ACPI device IDs for the Low Power
   Subsystem (LPSS) ACPI driver from Paul Drews.

* tag 'pm+acpi-3.13-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  powercap / RAPL: add support for ValleyView Soc
  PM / sleep: Fix memory leak in pm_vt_switch_unregister().
  cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
  cpufreq: remove sysfs files for CPUs which failed to come back after resume
  ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs

Merge tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

From Tony Lindgren:
Fix a regression for wrong interrupt numbers for some devices after
the sparse IRQ conversion, fix DRA7 console output for earlyprintk,
and fix the LDP LCD backlight when DSS is built into the kernel and
not as a loadable module.

* tag 'omap-for-v3.13/intc-ldp-fix' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: OMAP2+: Fix LCD panel backlight regression for LDP legacy booting
  ARM: OMAP2+: hwmod_data: fix missing OMAP_INTC_START in irq data
  ARM: DRA7: hwmod: Fix boot crash with DEBUG_LL
  + v3.13-rc5
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman:
Second Round of Renesas ARM based SoC Fixes for v3.13

* r8a7790 (R-Car H2) based Lager board
  - Correct SHDI resource sizes
    This bug has been present since sdhi resources were added to the r8a7790 by
    8c9b1aa4 ("ARM: shmobile: r8a7790: add MMCIF and SDHI DT
    templates") in v3.11-rc2.

* r8a7778 (R-Car M1) based Bock-W board
  - Correct DMA mask
    This resolves a regression introduced by 4dcfa600
    ("ARM: DMA-API: better handing of DMA masks for coherent allocations")
    in v3.12-rc1.

* r8a7740 (R-Mobile A1) based Armadillo board
  - Add PWM backlight power supply
    This resolves a regression introduced by 22ceeee1
    ("pwm-backlight: Add power supply support") in v3.12.

* tag 'renesas-fixes2-for-v3.13' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: r8a7790: fix shdi resource sizes
  ARM: shmobile: bockw: fixup DMA mask
  ARM: shmobile: armadillo: Add PWM backlight power supply
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NOlof Johansson <olof@lixom.net>

After commit 88f718e3
"ARM: pxa: delete the custom GPIO header" a compilation
error was introduced in the PXA25x gadget driver.
An attempt to fix the problem was made in
commit b144e4ab
"usb: gadget: fix pxa25x compilation problems"
by explictly stating the driver needs the <mach/hardware.h>
header, which solved the compilation for a few boards,
such as the pxa255-idp and its defconfig.

However the Lubbock board has this special clause in
drivers/usb/gadget/pxa25x_udc.c:

This include file has an implicit dependency on
<mach/irqs.h> having been included before <mach/lubbock.h>
was included.

Before commit 88f718e3
"ARM: pxa: delete the custom GPIO header" this implicit
dependency for the pxa25x_udc compile on the Lubbock was
satisfied by <linux/gpio.h> implicitly including
<mach/gpio.h> which was in turn including <mach/irqs.h>,
apart from the earlier added <mach/hardware.h>.

Fix this by having the PXA25x <mach/lubbock.h> explicitly
include <mach/irqs.h>.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Cc: Greg Kroah-Hartmann <gregkh@linuxfoundation.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'for-v3.13-rc/hwmod-fixes-b' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into debug-ll-and-ldp-backlight-fix

A few OMAP hwmod fixes for v3.13-rc.  One patch fixes some IRQ
problems with GPMC, RNG, and ISP/IVA MMUs on OMAP2/3.  The other fixes
some problems with DEBUG_LL on DRA7xx.

Basic build, boot, and PM test logs are available here:

http://www.pwsan.com/omap/testlogs/hwmod_fixes_b_v3.13-rc/20131226021920/

Looks like the LCD panel on LDP has been broken quite a while, and
recently got fixed by commit 0b2aa8be (gpio: twl4030: Fix regression
for twl gpio output). However, there's still an issue left where the panel
backlight does not come on if the LCD drivers are built into the
kernel.

Fix the issue by registering the DPI LCD panel only after the twl4030
GPIO has probed.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[tony@atomide.com: updated per Tomi's comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

* powercap:
  powercap / RAPL: add support for ValleyView Soc

* acpi-lpss:
  ACPI: Add BayTrail SoC GPIO and LPSS ACPI IDs

* pm-cpufreq:
  cpufreq: Use CONFIG_CPU_FREQ_DEFAULT_* to set initial policy for setpolicy drivers
  cpufreq: remove sysfs files for CPUs which failed to come back after resume

* pm-sleep:
  PM / sleep: Fix memory leak in pm_vt_switch_unregister().

Pull ext4 fixes from Ted Ts'o:
 "A collection of bug fixes destined for stable and some printk cleanups
  and a patch so that instead of BUG'ing we use the ext4_error()
  framework to mark the file system is corrupted"

* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: add explicit casts when masking cluster sizes
  ext4: fix deadlock when writing in ENOSPC conditions
  jbd2: rename obsoleted msg JBD->JBD2
  jbd2: revise KERN_EMERG error messages
  jbd2: don't BUG but return ENOSPC if a handle runs out of space
  ext4: Do not reserve clusters when fs doesn't support extents
  ext4: fix del_timer() misuse for ->s_err_report
  ext4: check for overlapping extents in ext4_valid_extent_entries()
  ext4: fix use-after-free in ext4_mb_new_blocks
  ext4: call ext4_error_inode() if jbd2_journal_dirty_metadata() fails

Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) and commit
ec2c0825 (ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ)
updated the way interrupts for OMAP2/3 devices are defined in the
HWMOD data structures to being an index plus a fixed offset (defined
by OMAP_INTC_START).

Couple of irqs in the OMAP2/3 hwmod data were misconfigured completely
as they were missing this OMAP_INTC_START relative offset. Add this
offset back to fix the incorrect irq data for the following modules:
	OMAP2 - GPMC, RNG
	OMAP3 - GPMC, ISP MMU & IVA MMU
Signed-off-by: NSuman Anna <s-anna@ti.com>
Fixes: 7d7e1eba ("ARM: OMAP2+: Prepare for irqs.h removal")
Fixes: ec2c0825 ("ARM: OMAP2+: Remove hardcoded IRQs and enable SPARSE_IRQ")
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

With commit '7dedd346: ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with
 DEBUG_LL' we moved from parsing cmdline to identify uart used for earlycon
to using the requsite hwmod CONFIG_DEBUG_OMAPxUARTy FLAGS.

On DRA7 though, we seem to be missing this flag, and atleast on the DRA7 EVM
where we use uart1 for console, boot fails with DEBUG_LL enabled.
Reported-by: NLokesh Vutla <lokeshvutla@ti.com>
Tested-by:  Lokesh Vutla <lokeshvutla@ti.com> # on a different base
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Fixes: 7dedd346 ("ARM: OMAP2+: hwmod: Fix a crash in _setup_reset() with DEBUG_LL")
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Pull block fixes from Jens Axboe:
 - fix for a memory leak on certain unplug events
 - a collection of bcache fixes from Kent and Nicolas
 - a few null_blk fixes and updates form Matias
 - a marking of static of functions in the stec pci-e driver

* 'for-linus' of git://git.kernel.dk/linux-block:
  null_blk: support submit_queues on use_per_node_hctx
  null_blk: set use_per_node_hctx param to false
  null_blk: corrections to documentation
  null_blk: warning on ignored submit_queues param
  null_blk: refactor init and init errors code paths
  null_blk: documentation
  null_blk: mem garbage on NUMA systems during init
  drivers: block: Mark the functions as static in skd_main.c
  bcache: New writeback PD controller
  bcache: bugfix for race between moving_gc and bucket_invalidate
  bcache: fix for gc and writeback race
  bcache: bugfix - moving_gc now moves only correct buckets
  bcache: fix for gc crashing when no sectors are used
  bcache: Fix heap_peek() macro
  bcache: Fix for can_attach_cache()
  bcache: Fix dirty_data accounting
  bcache: Use uninterruptible sleep in writeback
  bcache: kthread don't set writeback task to INTERUPTIBLE
  block: fix memory leaks on unplugging block device
  bcache: fix sparse non static symbol warning

Pull cgroup fixes from Tejun Heo:
 "Two fixes.  One fixes a bug in the error path of cgroup_create().  The
  other changes cgrp->id lifetime rule so that the id doesn't get
  recycled before all controller states are destroyed.  This premature
  id recycling made memcg malfunction"

* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: don't recycle cgroup id until all csses' have been destroyed
  cgroup: fix cgroup_create() error handling path

Pull percpu fix from Tejun Heo:
 "A single commit to fix a spurious sparse warning coming from
  DEFINE_PER_CPU()'s hack to support the use of weak symbols.  Shouldn't
  cause observable behavior change"

* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
  percpu: fix spurious sparse warnings from DEFINE_PER_CPU()

Pull libata fixes from Tejun Heo:
 "There's one interseting commit - "libata, freezer: avoid block device
  removal while system is frozen".  It's an ugly hack working around a
  deadlock condition between driver core resume and block layer device
  removal paths through freezer which was made more reproducible by
  writeback being converted to workqueue some releases ago.  The bug has
  nothing to do with libata but it's just an workaround which is easy to
  backport.  After discussion, Rafael and I seem to agree that we don't
  really need kernel freezables - both kthread and workqueue.  There are
  few specific workqueues which constitute PM operations and require
  freezing, which will be converted to use workqueue_set_max_active()
  instead.  All other kernel freezer uses are planned to be removed,
  followed by the removal of kthread and workqueue freezer support,
  hopefully.

  Others are device-specific fixes.  The most notable is the addition of
  NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
  M500 SSDs which otherwise suffers data corruption"

* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  libata, freezer: avoid block device removal while system is frozen
  libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
  libata: disable a disk via libata.force params
  ahci: bail out on ICH6 before using AHCI BAR
  ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
  libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8

Commit 2171364d ("powerpc: Add HWCAP2 aux entry") introduced a new
AT_ auxv entry type AT_HWCAP2 but failed to update AT_VECTOR_SIZE_BASE
accordingly.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Fixes: 2171364d (powerpc: Add HWCAP2 aux entry)
Cc: stable@vger.kernel.org
Acked-by: NMichael Neuling <michael@neuling.org>
Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull SELinux fixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  selinux: selinux_setprocattr()->ptrace_parent() needs rcu_read_lock()
  selinux: fix broken peer recv check

Pull ext2 fix from Jan Kara:
 "One simple fix of oops in ext2 which was recently hit by Christoph"

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
  ext2: Fix oops in ext2_get_block() called from ext2_quota_write()

Pull infiniband fixes from Roland Dreier:
 "Last batch of InfiniBand/RDMA changes for 3.13 / 2014:
   - Additional checks for uverbs to ensure forward compatibility,
     handle malformed input better.
   - Fix potential use-after-free in iWARP connection manager.
   - Make a function static"

* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/uverbs: Check access to userspace response buffer in extended command
  IB/uverbs: Check input length in flow steering uverbs
  IB/uverbs: Set error code when fail to consume all flow_spec items
  IB/uverbs: Check reserved fields in create_flow
  IB/uverbs: Check comp_mask in destroy_flow
  IB/uverbs: Check reserved field in extended command header
  IB/uverbs: New macro to set pointers to NULL if length is 0 in INIT_UDATA()
  IB/core: const'ify inbuf in struct ib_udata
  RDMA/iwcm: Don't touch cm_id after deref in rem_ref
  RDMA/cxgb4: Make _c4iw_write_mem_dma() static

selinux_setprocattr() does ptrace_parent(p) under task_lock(p),
but task_struct->alloc_lock doesn't pin ->parent or ->ptrace,
this looks confusing and triggers the "suspicious RCU usage"
warning because ptrace_parent() does rcu_dereference_check().

And in theory this is wrong, spin_lock()->preempt_disable()
doesn't necessarily imply rcu_read_lock() we need to access
the ->parent.
Reported-by: NEvan McNabb <emcnabb@redhat.com>
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaul Moore <pmoore@redhat.com>

Fix a broken networking check. Return an error if peer recv fails.  If
secmark is active and the packet recv succeeds the peer recv error is
ignored.
Signed-off-by: NChad Hanson <chanson@trustedcs.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaul Moore <pmoore@redhat.com>

Pull drm fixes from Dave Airlie:
 "Xmas fixes pull, all small nothing major, intel, radeon, one ttm
  regression, and one build fix"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/ttm: Fix swapin regression
  gpu: fix qxl missing crc32_le
  drm/radeon: fix asic gfx values for scrapper asics
  drm/i915: Use the correct GMCH_CTRL register for Sandybridge+
  drm/radeon: check for 0 count in speaker allocation and SAD code
  drm/radeon/dpm: disable ss on Cayman
  drm/radeon/dce6: set correct number of audio pins
  drm/i915: get a PC8 reference when enabling the power well
  drm/i915: change CRTC assertion on LCPLL disable
  drm/i915: Fix erroneous dereference of batch_obj inside reset_status
  drm/i915: Prevent double unref following alloc failure during execbuffer