The module clock is used for two purposes:
  - Wake-on-LAN (WoL), which is optional,
  - gPTP Timer Increment (GTI) configuration, which is mandatory.

As the clock is needed for GTI configuration anyway, WoL is always
available.  Hence remove duplication and repeated obtaining of the clock
by making GTI use the stored clock for WoL use.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rafał Miłecki says:

====================
net: support bgmac with B50212E B1 PHY

I got a report that a board with BCM47189 SoC and B50212E B1 PHY doesn't
work well some devices as there is massive ping loss. After analyzing
PHY state it has appeared that is runs in slave mode and doesn't auto
switch to master properly when needed.

This patchset fixes this by:
1) Adding new flag support to the PHY driver for setting master mode
2) Modifying bgmac to request master mode for reported hardware
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are 4 very similar PHYs:
0x600d84a1: BCM54210E (rev B0)
0x600d84a2: BCM54210E (rev B1)
0x600d84a5: B50212E (rev B0)
0x600d84a6: B50212E (rev B1)
that need setting master mode manually. It's because they run in slave
mode by default with Automatic Slave/Master configuration disabled which
can lead to unreliable connection with massive ping loss.

So far it was reported for a board with BCM47189 SoC and B50212E B1 PHY
connected to the bgmac supported ethernet device. Telling PHY driver to
setup PHY properly solves this issue.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of Broadcom's PHYs run by default in slave mode with Automatic
Slave/Master configuration disabled. It stops them from working properly
with some devices.

So far it has been verified for BCM54210E and BCM50212E which don't
work well with Intel's I217-LM and I218-LM:
http://ark.intel.com/products/60019/Intel-Ethernet-Connection-I217-LM
http://ark.intel.com/products/71307/Intel-Ethernet-Connection-I218-LM
I was told there is massive ping loss.

This commit adds support for a new flag which can be set by an ethernet
driver to fixup PHY setup.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the underlying master ever changes its L2 (e.g. bonding device),
then make sure that the IPvlan slaves always emit packets with the
current L2 of the master instead of the stale mac addr which was
copied during the device creation. The problem can be seen with
following script -

  #!/bin/bash
  # Create a vEth pair
  ip link add dev veth0 type veth peer name veth1
  ip link set veth0 up
  ip link set veth1 up
  ip link show veth0
  ip link show veth1
  # Create an IPvlan device on one end of this vEth pair.
  ip link add link veth0 dev ipvl0 type ipvlan mode l2
  ip link show ipvl0
  # Change the mac-address of the vEth master.
  ip link set veth0 address 02:11:22:33:44:55

Fixes: 2ad7bf36 ("ipvlan: Initial check-in of the IPVLAN driver.")
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexander Aring says:

====================
sched: act: ife: UAPI checks and performance tweaks

this patch series contains at first a patch which adds a check for
IFE_ENCODE and IFE_DECODE when a ife act gets created or updated and adding
handling of these cases only inside the act callback only.

The second patch use per-cpu counters and move the spinlock around so that
the spinlock is less being held in act callback.

The last patch use rcu for update parameters and also move the spinlock for
the same purpose as in patch 2.

Notes:
 - There is still a spinlock around for protecting the metalist and a
   rw-lock for another list. Should be migrated to a rcu list, ife
   possible.

 - I use still dereference in dump callback, so I think what I didn't
   got was what happened when rcu_assign_pointer will do when rcu read
   lock is held. I suppose the pointer will be updated, then we don't
   have any issue here.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch changes the parameter updating via RCU and not protected by a
spinlock anymore. This reduce the time that the spinlock is being held.
Signed-off-by: NAlexander Aring <aring@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch migrates the current counter handling which is protected by a
spinlock to a per-cpu counter handling. This reduce the time where the
spinlock is being held.
Signed-off-by: NAlexander Aring <aring@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the check of the two possible ife handlings encode
and decode to the init callback. The decode value is for usability
aspect and used in userspace code only. The current code offers encode
else decode only. This patch avoids any other option than this.
Signed-off-by: NAlexander Aring <aring@mojatatu.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roman Mashak says:

====================
net: sched: Fix IFE meta modules loading

Adjust module alias names of IFE meta modules and fix the bug that
prevented auto-loading IFE modules in run-time.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Macro __stringify_1() can stringify a macro argument, however IFE_META_*
are enums, so they never expand, however request_module expects an integer
in IFE module name, so as a result it always fails to auto-load.

Fixes: ef6980b6 ("introduce IFE action")
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Acked-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make style of module alias name consistent with other subsystems in kernel,
for example net devices.

Fixes: 084e2f65 ("Support to encoding decoding skb mark on IFE action")
Fixes: 200e10f4 ("Support to encoding decoding skb prio on IFE action")
Fixes: 408fbc22 ("net sched ife action: Introduce skb tcindex metadata encap decap")
Signed-off-by: NRoman Mashak <mrv@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delete unused channel variables in vxge-traffic.
Signed-off-by: NChristos Gkekas <chris.gekas@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This file contains unnecessary whitespaces as newlines, remove them,
found by looking at what struct tc_mirred looks like.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When af_mpls is built-in but the tunnel support is a module,
we get a link failure:

net/mpls/af_mpls.o: In function `mpls_init':
af_mpls.c:(.init.text+0xdc): undefined reference to `ip_tunnel_encap_add_ops'

This adds a Kconfig statement to prevent the broken
configuration and force mpls to be a module as well in
this case.

Fixes: bdc47641 ("ip_tunnel: add mpls over gre support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAmine Kherbouche <amine.kherbouche@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: ib_query_gid() patches

triggered by Parav Pandit here are 2 cleanup patches for usage of
ib_query_gid() in the smc-code.

Thanks, Ursula

v2 changes advised by Parav Pandit:
   extra check is_vlan_dev() in patch 2/2
   "RoCE" spelling
   added "Reported-by"
   added "Reviewed-by"
   added "Fixes"
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RoCEs ib_query_gid() takes a reference count on the net_device.
This reference count must be decreased by the caller.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Reported-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Fixes: 0cfdd8f9 ("smc: connection and link group creation")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SMC should not open code the function pointer get_netdev of the
IB device. Replacing ib_query_gid(..., NULL) with
ib_query_gid(..., gid_attr) allows access to the netdev.
Signed-off-by: NUrsula Braun <ubraun@linux.vnet.ibm.com>
Suggested-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NParav Pandit <parav@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Enable ACB for bcm_sf2 and bcmsysport

This patch series enables Broadcom's Advanced Congestion Buffering mechanism
which requires cooperation between the CPU/Management Ethernet MAC controller
and the switch.

I took the notifier approach because ultimately the information we need to
carry to the master network device is DSA specific and I saw little room for
generalizing beyond what DSA requires. Chances are that this is highly specific
to the Broadcom HW as I don't know of any HW out there that supports something
nearly similar for similar or identical needs.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have established the queue mapping between the switch port
egress queues and the SYSTEMPORT egress queues, we can turn on Advanced
Congestion Buffering (ACB) at the SYSTEMPORT level. This enables the
Ethernet MAC controller to get out of band flow control information
directly from the switch port and queue that it monitors such that its
internal TDMA can be appropriately backpressured.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn on the out of band Advanced Congestion Buffering (ACB) mechanism at
the switch level now that we have properly established the queue mapping
between the switch egress queues and the SYSTEMPORT egress queues. This
allows the switch to correctly backpressure the host system when one of
its queue drops below the configured thresholds.

This is also helping achieve so called "lossless" behavior by adapting
the TX interrupt pacing to the actual speed and capacity of the switch
port.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Establish a queue mapping between the DSA slave network device queues
created that correspond to switch port queues, and the transmit queue
that SYSTEMPORT manages.

We need to configure the SYSTEMPORT transmit queue with the switch port number
and switch port queue number in order for the switch and SYSTEMPORT hardware to
utilize the out of band congestion notification. This hardware mechanism works
by looking at the switch port egress queue and determines whether there is
enough buffers for this queue, with that class of service for a successful
transmission and if not, backpressures the SYSTEMPORT queue that is being used.

For this to work, we implement a notifier which looks at the
DSA_PORT_REGISTER event.  When DSA network devices are registered, the
framework calls the DSA notifiers when that happens, extracts the number
of queues for these devices and their associated port number, remembers
that in the driver private structure and linearly maps those queues to
TX rings/queues that we manage.

This scheme works because DSA slave network deviecs always transmit
through SYSTEMPORT so when DSA slave network devices are
destroyed/brought down, the corresponding SYSTEMPORT queues are no
longer used. Also, by design of the DSA framework, the master network
device (SYSTEMPORT) is registered first.

For faster lookups we use an array of up to DSA_MAX_PORTS * number of
queues per port, and then map pointers to bcm_sysport_tx_ring such that
our ndo_select_queue() implementation can just index into that array to
locate the corresponding ring index.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to tell the DSA master network device doing the actual
transmission what the desired switch port and queue number is for it to
resolve that to the internal transmit queue it is mapped to.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for communicating a given DSA network device's port
number and switch index, create a specialized DSA notifier and two
events: DSA_PORT_REGISTER and DSA_PORT_UNREGISTER that communicate: the
slave network device (slave_dev), port number and switch number in the
tree.

This will be later used for network device drivers like bcmsysport which
needs to cooperate with its DSA network devices to set-up queue mapping
and scheduling.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit df1ec1b9.

It turns out that memory allocated via dma_alloc_coherent is always
aligned to the size of the buffer, so there's no way the RRD and RFD
can ever be in separate 32-bit regions.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove three inline helpers that are no longer needed.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable old_flags is being assigned but is never read; it is redundant
and can be removed.

Cleans up clang warning: Value stored to 'old_flags' is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4_en XDP TX improvements

This patchset contains performance improvements
to the XDP_TX use case in the mlx4 Eth driver.

Patch 1 is a simple change in a function parameter type.
Patch 2 replaces a call to a generic function with the
  relevant parts inlined.
Patch 3 moves the write of descriptors' constant values
  from data path to control path.

Series generated against net-next commit:
833e0e2f net: dst: move cpu inside ifdef to avoid compilation warning
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In XDP_TX, some fields in tx_info and tx_desc are constants across
all entries of the different XDP_TX rings.
Assign values to these fields on ring creation time, rather than in
data-path.

Patchset performance tests:
Tested on ConnectX3Pro, Intel(R) Xeon(R) CPU E5-2680 v3 @ 2.50GHz
Single queue no-RSS optimization ON.

XDP_TX packet rate:
------------------------------
Before    | After     | Gain |
13.7 Mpps | 14.0 Mpps | %2.2 |
------------------------------
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function mlx4_en_tx_write_desc() is not optimized to use of XDP xmit.
Use the relevant parts inline instead.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct net_device parameter was passed only to extract
struct mlx4_en_priv out of it.
Here we pass the priv parameter directly.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ipgre_mpls_encap_hlen is local to the source and
does not need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'ipgre_mpls_encap_hlen' was not declared. Should it be static?

Fixes: bdc47641 ("ip_tunnel: add mpls over gre support")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The array sctp_sched_ops  is local to the source and
does not need to be in global scope, so make it static.

Cleans up sparse warning:
symbol 'sctp_sched_ops' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to the previous patch, use the device lookup functions
that bump device refcount and flag this as DOIT_UNLOCKED to avoid
rtnl mutex.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of relying on rtnl mutex bump device reference count.
After this change, values reported can change in parallel, but thats not
much different from current state, as anyone can change the settings
right after rtnl_unlock (and before userspace processed reply).

While at it, switch to GFP_KERNEL allocation.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
net: sched: get rid of cls_flower->egress_dev

Introduction of cls_flower->egress_dev was a workaround. Turned out
to be a bit ugly hack. So replace it with more generic and reusable
infrastructure.

This is a dependency of shared block introduction that will be send as
a follow-up patchsets group.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The helper and the struct field ares no longer used by any code,
so remove them.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only user of cls_flower->egress_dev is mlx5. So do the conversion
there alongside with the code originating the call in cls_flower
function fl_hw_replace_filter to the newly introduced egress device
callback infrastucture.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce infrastructure that allows drivers to register callbacks that
are called whenever tc would offload inserted rule and specified device
acts as tc action egress device.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return dev directly, NULL if not possible. That is enough.

Makes no sense to pass struct net * to get_dev op, as there is only one
net possible, the one the action was created in. So just store it in
mirred priv and use directly.

Rename the mirred op callback function.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>