Small updates to the EHCI driver's ISO support:

 - Get rid of the Kconfig option for full speed ISO.  It may
   not be perfect yet, but it hasn't appeared to be dangerous
   and pretty much every configuration wants it.

 - Instead of two places to disable an empty periodic schedule
   after an ISO transfer completes, just have one.

 - After the periodic schedule is disabled, we can short-circuit
   the schedule scan ... it can't possibly have more work to do.

Assuming a typical config with split iso enabled, the only change
in behavior should be almost unobservable:  quicker termination
of periodic scans when the schedule gets emptied.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by
uframe.  For an ITD's unused uframes it is 0, else it contains the same
value as itd->stream->usecs.  To check if an ITD's uframe is used, we can
instead test itd->hw_transaction[uframe]:  if used, it will be nonzero no
matter what endianess is used.

This patch replaces those two uses, eliminates itd->usecs[], and saves
eight bytes from each ITD.
Signed-off-by: NKarsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EHCI Glue driver for Intel IXP4XX EHCI USB controller
Signed-off-by: NVladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds device-tree-aware ehci-ppc-of driver.
The code is based on the ehci-ppc-soc driver by
Stefan Roese <sr@denx.de>.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Update the ohci-at91 bus glue to start understanding about the per-port
power switch GPIOs it's given (on the sam9263-ek and potentially other
boards).  For the moment this just claims them and forces them active
(assuming active-low power enables) whenever the HCD is loaded.

The assumption is still that board setup configures the GPIOs.  Using
gpio_request() tracks actual usage and guards against conflict.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a missing dependency which goofs up the xconfig display.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Kernel bugzilla entry #9569 reports a potential OOPS in some code
supporting the integrated root hub TT support used on ARC/TDI
derived cores.  (This seems to have been a longstanding issue.)

This patch cleans up usage of urb->dev->tt to avoid that potential
oops and also fixes some overly long lines.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some glue bits for the on-chip USB host controller in the Marvell Orion
family of ARM SoCs, which is basically EHCI compatible.
Signed-off-by: NTzachi Perelstein <tzachi@marvell.com>
Reviewed-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix warning:
drivers/usb/host/ehci-hcd.c:832:8: warning: symbol 'status' shadows an earlier one
drivers/usb/host/ehci-hcd.c:790:71: originally declared here
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a workaround for an issue reported with ISO transfers
on some EHCI controllers, most recently with VIA KT800 and PS3
EHCI silicon.

The issue is that the silicon doesn't necessarily seem to be done
using ISO DMA descriptors (itd, sitd) when it marks them inactive.
(One theory is that the ill-defined mechanism where hardware caches
periodic transfer descriptors isn't invalidating their state...)
With such silicon, quick re-use of those descriptors makes trouble.
Waiting until the next frame seems to be a sufficient workaround.

This patch ensures that the relevant descriptors aren't available
for immediate re-use.  It does so by not recycling them until after
issuing the completion callback which would reuse them by enqueueing
an URB and thus (re)allocating ISO DMA descriptors.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Cc: Masashi Kimoto <Masashi_Kimoto@hq.scei.sony.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1028) was mostly written by David Brownell; I made only
a few changes (extra log info and a small bug fix -- which might
account for why David's version had to be reverted).  It adds a new
watchdog timer to the ehci-hcd driver to be used exclusively for
detecting lost or missing IAA notifications.

Previously a shared timer had been used, which may have led to some
problems as reported by Christian Hoffmann.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The OHCI driver's IRQ handler, while processing a WDH interrupt, masks
and unmasks it.  I believe this is both broken (the write may still be
posted during the donelist processing it's trying to safeguard) and
useless as this IRQ may not be reissued until it's acked (unless this
legacy code is an uncommented workaround for some chip erratum).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: NBalaji Rao <balajirrao@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Continue is not needed at the bottom of a loop.

The semantic patch implementing this change is as follows:

@@
@@

for (...;...;...) {
   ...
   if (...) {
     ...
-   continue;
   }
}
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Convert from class_device to device for drivers/usb/core.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

I2C driver IDs are optional, so if you don't need one, just omit it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:

http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html

This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix.  The drivers will still bind against
the older names also.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.

This mechanism can't be used on some controllers.  Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.

This patch removes the optimisation and makes the code clearer.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Host controller IRQs are supposed to be serviced with interrupts
disabled.  This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it.  It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().

This fixes Bugzilla #9335.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A recent patch added software synchronization during EHCI startup,
so ports aren't switched away from the companion controllers after
resets have started.  This patch adds a short delay letting hardware
finish that port switching before any new resets begin ... so both
ends of that hardware race window are closed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Dave Miller <davem@davemloft.net>
Cc: Dely Sy <dely.l.sy@intel.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a bug introduced by
commit b22817b3.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove various newly-introduced compiler warnings for OHCI.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix ssb_ohci_probe() build bug:

 drivers/built-in.o: In function `ssb_ohci_probe':
 ohci-hcd.c:(.text+0xbff39): undefined reference to `ssb_device_enable'
 ohci-hcd.c:(.text+0xbff6f): undefined reference to `ssb_admatch_base'
 ohci-hcd.c:(.text+0xbff8b): undefined reference to `ssb_admatch_size'
 ohci-hcd.c:(.text+0xbffe5): undefined reference to `ssb_device_disable'
 [...]

the reason was that this Kconfig combination was allowed:

 CONFIG_SSB=m
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_SSB=y

the fix is to require a modular USB_OHCI_HCD build when SSB is modular.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1003) changes uhci-hcd to treat the URB_ISO_ASAP flag
the same as other host controller drivers, namely, to schedule an Iso
URB for the first available time slot that hasn't already expired.
URBs in which the flag isn't set will be scheduled for the first slot
following the last URB, even if it has expired.

This fixes a problem reported by Martin Bachem.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Found these while looking at printk uses.

Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ohci_bus_{suspend,resume} exists only if we have CONFIG_PM; do the same
thing as other subdrivers...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order.  If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused.  The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds SSB bus glue for the USB OHCI HCD. 
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleanup: references to two PM routines (and HCD entry points)
that no longer exist are swapped with their replacements.

Evidently au1xxx and ppc-soc EHCI support doesn't get compiled
with power management very much, or these build bugs would have
been patched long ago.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add OHCI big endian frame_no quirk.  The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field.  And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.

Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that accessed register of this controller after
having called iounmap().
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that does not work in the big endian machine.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>