Signed-off-by: NAndy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

The gdbserial protocol handler should return an empty packet instead
of an error string when ever it responds to a command it does not
implement.

The problem cases come from a debugger client sending
qTBuffer, qTStatus, qSearch, qSupported.

The incorrect response from the gdbstub leads the debugger clients to
not function correctly.  Recent versions of gdb will not detach correctly as a result of this behavior.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>

One of the driving forces behind integrating another front end (kdb)
to the debug core is to allow front end commands to be accessible via
gdb's monitor command.  It is true that you could write gdb macros to
get certain data, but you may want to just use gdb to access the
commands that are available in the kdb front end.

This patch implements the Rcmd gdb stub packet.  In gdb you access
this with the "monitor" command.  For instance you could type "monitor
help", "monitor lsmod" or "monitor ps A" etc...

There is no error checking or command restrictions on what you can and
cannot access at this point.  Doing something like trying to set
breakpoints with the monitor command is going to cause nothing but
problems.  Perhaps in the future only the commands that are actually
known to work with the gdb monitor command will be available.
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

The design of the kdb shell requires that every device that can
provide input to kdb have a polling routine that exits immediately if
there is no character available.  This is required in order to get the
page scrolling mechanism working.

Changing the kernel debugger I/O API to require all polling character
routines to exit immediately if there is no data allows the kernel
debugger to process multiple input channels.

NO_POLL_CHAR will be the return code to the polling routine when ever
there is no character available.

CC: linux-serial@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

These are the minimum changes to the kgdb core in order to enable an
API to connect a new front end (kdb) to the debug core.

This patch introduces the dbg_kdb_mode variable controls where the
user level I/O is routed.  It will be routed to the gdbstub (kgdb) or
to the kdb front end which is a simple shell available over the kgdboc
connection.

You can switch back and forth between kdb or the gdb stub mode of
operation dynamically.  From gdb stub mode you can blindly type
"$3#33", or from the kdb mode you can enter "kgdb" to switch to the
gdb stub.

The logic in the debug core depends on kdb to look for the typical gdb
connection sequences and return immediately with KGDB_PASS_EVENT if a
gdb serial command sequence is detected.  That should allow a
reasonably seamless transition between kdb -> gdb without leaving the
kernel exception state.  The two gdb serial queries that kdb is
responsible for detecting are the "?" and "qSupported" packets.

CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Acked-by: NMartin Hicks <mort@sgi.com>

Split the former kernel/kgdb.c into debug_core.c which contains the
kernel debugger exception logic and to the gdbstub.c which contains
the logic for allowing gdb to talk to the debug core.

This also created a private include file called debug_core.h which
contains all the definitions to glue the debug_core to any other
debugger connections.

CC: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>