Now the fetching of board data also uses nvram_read_u16 and not
simple_strtoul any more.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the sprom parsing from nvram into sprom.c. There are all values
needed for sprom version 1 to 9 read from nvram and there are more
sanity checks added. This is based on the sprom parsing in the open
source part of the Broadcom SDK.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Explicitly enforce an char array of 6 bytes for the mac address.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since eb9ae7f2 (gpio: fix build error in include/asm-generic/gpio.h)
the generic version of gpio.h calls __gpio_{set,get}_value which we
do not define. Get rid of asm-generic/gpio.h and define the missing
stubs directly for BCM47xx to build.
Reported-by: NRalf Baechle <ralf@linux-mips.org>
To: linux-mips@linux-mips.org
CC: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: https://patchwork.linux-mips.org/patch/2885/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some devices like the Netgear WGT634u are using minuses between the blocks
of the MAC address and other devices are using colons to separate them.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2366/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Nvram_getenv should behave like cfe_getenv. cfe_getenv returns 0 on
success and -9 if the value was not found. If the input was wrong -8
will be returned by cfe_getenv.  Change nvram_getenv to do the same.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1520/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:

...
[    0.424000] b44: b44.c:v2.0
[    0.424000] b44: Invalid MAC address found in EEPROM
[    0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[    0.436000] b44: probe of ssb0:1 failed with error -22
...

The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.

Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.

[Ralf: sorted out header file inclusions.  Lots of unneded headers and such
that should have been included.]
Signed-off-by: NWaldemar Brodkorb <wbx@openadk.org>
Reviewed-by: NPhil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

gpio_direction_output should also set an output value according to the API.

Signed-off-by: Matthieu CASTET <castet.matthieu@free.fr> 
Acked-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The GPIO API is supposed to return 0 or a negative error code,
but the SSB GPIO functions return the bitmask of the GPIO register.
Fix this by ignoring the bitmask and always returning 0. The SSB GPIO functions can't fail.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch simplifies the BCM47xx GPIO code by using the new SSB GPIO
API, which does a lot things that were implemented directly in the
BCM47xx code.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch removes the remaining reference to the BCM947xx development
board codename.
Signed-off-by: NFlorian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>