So far, there was possible only to register a single filter chain
pointer to block->chain[0]. However, when the blocks will get shareable,
we need to allow multiple filter chain pointers registration.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michael Chan says:

====================
bnxt_en: Updates for net-next.

First, we upgrade the firmware interface spec.  Due to a change in
the toolchains, the auto-generated bnxt_hsi.h does not match the
old bnxt_hsi.h and the patch is really big.  This should be just
one-time.  Going forward, changes should be incremental.

The next 10 patches implement a new scheme for the PF and VF drivers
to allocate and reserve resources.  The new scheme is more flexible
and allows dynamic and asymmetric distribution of resources, whereas
the old scheme is static and even distribution.

The last few patches add cacheline size setting, a couple of PCI IDs,
better management of VF MAC address, and a better parent switchdev ID
for dual-port devices.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the driver exports different switchdev PARENT_IDs for
representors belonging to different SR-IOV PF-pools of an adapter.
This is not correct as the adapter can switch across all vports
of an adapter. This patch fixes this by exporting a common switchdev
PARENT_ID for all reps of an adapter. The PCIE DSN is used as the id.
Signed-off-by: NSathya Perla <sathya.perla@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip supports 64-byte and 128-byte cache line size for more optimal
DMA performance when matched to the CPU cache line size.  The default is 64.
If the system is using 128-byte cache line size, set it to 128.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context.  This will allow "ip link show"
to display all VF MAC addresses.

Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.

Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnxt_check_rings() is called by ethtool, XDP setup, and ndo_setup_tc()
to see if there are enough resources to support the new configuration.
Expand the call to test all resources if the firmware supports the new
API.  With the more flexible resource allocation scheme, this call must
be made to check that all resources are available before committing to
allocate the resources.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.

The min is the absolute minimum for each VF to function.  The max is the
global resources minus the resources used by the PF.  Each VF is
guaranteed the min.  Up to max resources may be available for some VFs.

The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources.  The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_rfs_capable(), add call to reserve vnic resources to support
NTUPLE.  Return true if we can successfully reserve enough vnics.
Otherwise, reserve the minimum 1 VNIC for normal operations not
supporting NTUPLE and return false.

Also, suppress warning message about not enough resources for NTUPLE when
only 1 RX ring is in use.  NTUPLE filters by definition require multiple
RX rings.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new method will call firmware to reserve the desired tx, rx, cmpl
rings, ring groups, stats context, and vnic resources.  A second query
call will check the actual resources that firmware is able to reserve.
The driver will then trim and adjust based on the actual resources
provided by firmware.  The driver will then reserve the final resources
in use.

This method is a more flexible way of using hardware resources.  The
resources are not fixed and can by adjusted by firmware.  The driver
adapts to the available resources that the firmware can reserve for
the driver.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In combined mode, the driver is currently not setting RX and TX ring
numbers the same when firmware can allocate more RX than TX or vice versa.
This will confuse the user as the ethtool convention assumes they are the
same in combined mode.  Fix it by adding bnxt_trim_dflt_sh_rings() to trim
RX and TX ring numbers to be the same as the completion ring number in
combined mode.

Note that if TCs are enabled and/or XDP is enabled, the number of TX rings
will not be the same as RX rings in combined mode.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new API HWRM_FUNC_RESOURCE_QCAPS provides min and max hardware
resources.  Use the new API when it is supported by firmware.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources.  This new structure is common for PFs and VFs.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After SRIOV has been enabled and disabled, the MSIX vectors assigned to
the VFs have to be re-initialized.  Otherwise they cannot be re-used by
the PF.  For example, increasing the number of PF rings after disabling
SRIOV may fail if the PF uses MSIX vectors previously assigned to the VFs.

To fix this, we add logic in bnxt_restore_pf_fw_resources() to close the
NIC, clear and re-init MSIX, and re-open the NIC.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new __bnxt_close_nic() function to do all the work previously done
in bnxt_close_nic() except waiting for SRIOV configuration.  The new
function will be used in the next patch as part of SRIOV cleanup.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The version has new firmware APIs to allocate PF/VF resources more
flexibly.

New toolchains were used to generate this file, resulting in a one-time
large diffstat.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Martin Blumenstingl says:

====================
dwmac-meson8b: clock fixes for Meson8b

this series is now successfully tested, thus we think it's ready to be
applied to your net-next tree.

Emiliano reported [0] that he couldn't get dwmac-meson8b to work on his
Odroid-C1. This is the (hopefully) final version of this series, which
was successfully tested.

Due to the fact that the public S805/S905/S912 datasheets all seem to
be outdated regarding the description of the PRG_ETH0 (also called
PRG_ETHERNET_ADDR0) register Linus Lüssing offered to help testing with
an oscilloscope and an Odroid-C1. I would like to say HUGE thanks to him
at this point as he spent hours figuring out the effects of the bits
that are (though to be) relevant to get Ethernet working on the
Odroid-C1.
We tested three scenarios, all based on version 3 of this series:
1) MPLL2 at ~500MHz, m250_div set to 1, bit 10 enabled
this resulted in a clock rate twice as high as expected at the RGMII TX
clock pin (250MHz instead of 125MHz for Gbit connections and 50MHz
instead of 25MHz for 100Mbit/s connections). it did not change the
rate at the XTAL_IN pin of PHY (which stayed consistenly at 25MHz)
2) MPLL2 at ~250MHz, m250_div set to 1, bit 10 disabled
the oscilloscope shows "no clock" for the RGMII TX clock pin at it's
highest resolution (and random rates at lower resolutions). XTAL_IN is
still at 25MHz
3) MPLL2 at ~250MHz, m250_div set to 1, bit 10 enabled
this resulted in a 125MHz signal at the RGMII TX clock pin for Gbit
speeds and 25MHz for 100Mbit/s - both values are as expected. The rate
on the XTAL_IN pin was at 25MHz
-> boot-logs (with the PRG_ETH0 register value) and screenshots from the
readings of the oscilloscope can be found at:
https://metameute.de/~tux/linux/amlogic/odroidc1/ethernet/

Version 4 of this series is based on the results from Linus Lüssing's
help with the oscilloscope and Odroid-C1.
Unfortunately I don't have any Meson8b boards with RGMII PHY so I could
only partially test this. @Emiliano: Could you please give this version
a try and let me know about the results (preferably with a "Tested-by"
if it works)?
You obviously still need your two "ARM: dts: meson8b" patches which
- add the amlogic,meson8b-dwmac" compatible to meson8b.dtsi
- enable Ethernet on the Odroid-C1 (according to your last thest a TX
  delay of 4ns is required to make it work properly)

When testing on Meson8b this also needs a fix for the MPLL clock driver:
"clk: meson: mpll: use 64-bit maths in params_from_rate", see:
https://patchwork.kernel.org/patch/10131677/

I have tested this myself on a Khadas VIM (GXL SoC, internal RMII PHY)
and a Khadas VIM2 (GXM SoC, external RGMII PHY). Both are still working
fine (so let's hope that this also fixes your Meson8b issue :)).

changes since v4 at [4]:
- dropped "RFT" status since Jerome tested this series successfully!
- dropped PATCH #2 ("simplify generating the clock names"). I will
  improve the whole clock registration in a separate series. since that
  patch didn't really improve anything I dropped it for now
- added Jerome's Acked-/Reviewed-/Tested-by's - many thanks!

changes since v3 at [3]:
- renamed the function PATCH #1 from meson8b_init_rgmii_clk to
  meson8b_init_rgmii_tx_clk since we now know what the register bits
  mean
- rewrote PATCH #3 because bit 10 is a gate clock and it seems that
  there is an internal fixed divide-by-2 clock. see the patch
  description for a detailed explanation
- updated the description of PATCH #4 and #5 as the clock we're trying
  to fix is the "RGMII TX" clock (old version stated that this is the
  "RGMII clock" or "PHY reference clock"). also updated the numbers in
  the description now that we have the clock hierarchy right (at least
  we hope so)

changes since v2 at [2]:
- added PATCH #2 to make the following patch easier
- Emiliano reported that there's currently another bug in the
  dwmac-meson8b driver which prevents it from working with RGMII PHYs on
  Meson8b: bit 10 of the PRG_ETH0 register is configures a clock gate
  (instead of a divide by 5 or divide by 10 clock divider). This has not
  been visible on GXBB and later due to the input clock which always led
  to a selection of "divide by 10" (which is done internally in the IP
  block, but the bit actually means "enable RGMII clock output").
  PATCH #3 was added to address this issue.
- the commit message of PATCH #4 and #5 (formerly PATCH #2 and #3) were
  updated and the patch itself rebased because the m25_div clock was
  removed with the new PATCH #3 (so some of the statements were not
  valid anymore)

changes since v1 at [1]:
- changed the subject of the cover-letter to indicate that this is all
  about the RGMII clock
- added PATCH #1 which ensures that we don't unnecessarily change the
  parent clocks in RMII mode (and also makes the code easier to
  understand)
- changed subject of PATCH #2 (formerly PATCH #1) to state that this
  is about the RGMII clock
- added Jerome's Reviewed-by to PATCH #2 (formerly PATCH #1)
- replaced PATCH #3 (formerly PATCH #2) with one that sets
  CLK_SET_RATE_PARENT on the mux and thus re-configures the MPLL2 clock
  on Meson8b correctly

[0] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005596.html
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005848.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005861.html
[3] http://lists.infradead.org/pipermail/linux-amlogic/2017-December/005899.html
[4] http://lists.infradead.org/pipermail/linux-amlogic/2018-January/006125.html
====================
Tested-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On Meson8b the only valid input clock is MPLL2. The bootloader
configures that to run at 500002394Hz which cannot be divided evenly
down to 125MHz using the m250_div clock. Currently the common clock
framework chooses a m250_div of 2 - with the internal fixed
"divide by 10" this results in a RGMII TX clock of 125001197Hz (120Hz
above the requested 125MHz).

Letting the common clock framework propagate the rate changes up to the
parent of m250_mux allows us to get the best possible clock rate. With
this patch the common clock framework calculates a rate of
very-close-to-250MHz (249999701Hz to be exact) for the MPLL2 clock
(which is the mux input). Dividing that by 2 (which is an internal,
fixed divider for the RGMII TX clock) gives us an RGMII TX clock of
124999850Hz (which is only 150Hz off the requested 125MHz, compared to
1197Hz based on the MPLL2 rate set by u-boot and the Amlogic GPL kernel
sources).

SoCs from the Meson GX series are not affected by this change because
the input clock is FCLK_DIV2 whose rate cannot be changed (which is fine
since it's running at 1GHz, so it's already a multiple of 250MHz and
125MHz).

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Suggested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Meson8b only supports MPLL2 as clock input. The rate of the MPLL2 clock
set by Odroid-C1's u-boot is close to (but not exactly) 500MHz. The
exact rate is 500002394Hz, which is calculated in
drivers/clk/meson/clk-mpll.c using the following formula:
DIV_ROUND_UP_ULL((u64)parent_rate * SDM_DEN, (SDM_DEN * n2) + sdm)
Odroid-C1's u-boot configures MPLL2 with the following values:
- SDM_DEN = 16384
- SDM = 1638
- N2 = 5

The 250MHz clock (m250_div) inside dwmac-meson8b driver is derived from
the MPLL2 clock. Due to MPLL2 running slightly faster than 500MHz the
common clock framework chooses a divider which is too big to generate
the 250MHz clock (a divider of 2 would be needed, but this is rounded up
to a divider of 3). This breaks the RTL8211F RGMII PHY on Odroid-C1
because it requires a (close to) 125MHz RGMII TX clock (on Gbit speeds,
the IP block internally divides that down to 25MHz on 100Mbit/s
connections and 2.5MHz on 10Mbit/s connections - we don't need any
special configuration for that).

Round the divider to the closest value to prevent this issue on Meson8b.
This means we'll now end up with a clock rate for the RGMII TX clock of
125001197Hz (= 125MHz plus 1197Hz), which is close-enough to 125MHz.
This has no effect on the Meson GX SoCs since there fclk_div2 is used as
input clock, which has a rate of 1000MHz (and thus is divisible cleanly
to 250MHz and 125MHz).

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tests (using an oscilloscope and an Odroid-C1 board with a RTL8211F
RGMII PHY) have shown that the PRG_ETH0 register behaves as follows:
- bit 4 is a mux to choose between two parent clocks. according to the
  public S805 datasheet the only supported parent clock is MPLL2 (this
  was not verified using the oscilloscope).
  The public S805/S905 datasheet claims that this bit is reserved.
- bits 9:7 control a one-based divider (register value 1 means "divide
  by 1", etc.) for the input clock. we call this clock the "m250_div"
  clock because it's value is always supposed to be (close to) 250MHz
  (see below for an explanation).
  The description in the public S805/S905 datasheet is a bit cryptic,
  but it comes down to "input clock = 250MHz * value" (which could also
  be expressed as "250MHz = input clock / value")
- there seems to be an internal fixed divide-by-2 clock which takes the
  output from the m250_div and divides it by 2. This is not unusual on
  Amlogic SoCs, since the SDIO (MMC) driver also uses an internal fixed
  divide-by-2 clock.
  This is not documented in the public S805/S905 datasheet
- bit 10 controls a gate clock which enables or disables the RGMII TX
  clock (which is an output on the MAC/SoC and an input in the PHY). we
  call this the "rgmii_tx_en" clock. if this bit is set to "0" the RGMII
  TX clock output is close to 0
  The description for this bit in the public S805/S905 datasheet is
  "Generate 25MHz clock for PHY". Based on these tests it's believed
  that this is wrong, and should probably read "Generate the 125MHz
  RGMII TX clock for the PHY"
- the RGMII TX clock has to be set to 125MHz - the IP block adjusts the
  output (automatically) depending on the line speed (RGMII specifies
  that Gbit connections use a 125MHz clock, 100Mbit/s connections use a
  25MHz clock and 10Mbit/s connections use a 2.5MHz clock. only Gbit and
  100Mbit/s were tested with an oscilloscope). Due to the requirement
  that this clock always has to be set to 125MHz and due to the fixed
  divide-by-2 parent clock this means that m250_div will always end up
  with a rate of (close to) 250MHz.
- bits 6:5 are the TX delay, which is also named "clock phase" in some
  of Amlogic's older GPL kernel sources.

The PHY also has an XTAL_IN pin where a 25MHz clock has to be provided.
Tests with the oscilloscope have shown that this is routed to a crystal
right next to the RTL8211F PHY. The same seems to be true on the Khadas
VIM2 (which uses a GXM SoC) board - however the 25MHz crystal is on the
other side of the PCB there.

This updates the clocks in the dwmac-meson8b driver by replacing the
"m25_div" with the "rgmii_tx_en" clock and additionally introducing a
fixed divide-by-2 clock between "m250_div" and "rgmii_tx_en".
Now we also need to set a frequency of 125MHz on the RGMII clock
(opposed to the 25MHz we set before, with that non-existing
divide-by-5-or-10 divider).

Special thanks go to Linus Lüssing for testing the various bits and
checking the results with an oscilloscope on his Odroid-C1!

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Reported-by: NEmiliano Ingrassia <ingrassia@epigenesys.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: NJerome Brunet <jbrunet@baylibre.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Neither the m25_div_clk nor the m250_div_clk or m250_mux_clk are used in
RMII mode. The m25_div_clk output is routed to the RGMII PHY's "RGMII
clock".
This means that we don't need to configure the clocks in RMII mode. The
driver however did this - with no effect since the clocks are not routed
to the PHY in RMII mode.

While here also rename meson8b_init_clk to meson8b_init_rgmii_tx_clk to
make it easier to understand the code.

Fixes: 566e8251 ("net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC")
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: NJerome Brunet <jbrunet@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 0dfb33a0 ("sch_red: report backlog information") copied
child's backlog into RED's backlog.  Back then RED did not maintain
its own backlog counts.  This has changed after commit 2ccccf5f
("net_sched: update hierarchical backlog too") and commit d7f4f332
("sch_red: update backlog as well").  Copying is no longer necessary.

Tested:

$ tc -s qdisc show dev veth0
qdisc red 1: root refcnt 2 limit 400000b min 30000b max 30000b ecn
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 0 requeues 0)
 backlog 1260b 14p requeues 14
  marked 0 early 0 pdrop 0 other 0
qdisc tbf 2: parent 1: rate 1Kbit burst 15000b lat 3585.0s
 Sent 20942 bytes 221 pkt (dropped 0, overlimits 138 requeues 0)
 backlog 1260b 14p requeues 14

Recently RED offload was added.  We need to make sure drivers don't
depend on resetting the stats.  This means backlog should be treated
like any other statistic:

  total_stat = new_hw_stat - prev_hw_stat;

Adjust mlxsw.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NNogah Frankel <nogahf@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The latest merge between net and net-next introduced a complier assert in
mlx5 driver.  In hca_cap_bits older fields are kept along with newer
fields that should have replaced them.

Fixes: c02b3741 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net")
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Overlapping changes all over.

The mini-qdisc bits were a little bit tricky, however.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-01-17

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Add initial BPF map offloading for nfp driver. Currently only
   programs were supported so far w/o being able to access maps.
   Offloaded programs are right now only allowed to perform map
   lookups, and control path is responsible for populating the
   maps. BPF core infrastructure along with nfp implementation is
   provided, from Jakub.

2) Various follow-ups to Josef's BPF error injections. More
   specifically that includes: properly check whether the error
   injectable event is on function entry or not, remove the percpu
   bpf_kprobe_override and rather compare instruction pointer
   with original one, separate error-injection from kprobes since
   it's not limited to it, add injectable error types in order to
   specify what is the expected type of failure, and last but not
   least also support the kernel's fault injection framework, all
   from Masami.

3) Various misc improvements and cleanups to the libbpf Makefile.
   That is, fix permissions when installing BPF header files, remove
   unused variables and functions, and also install the libbpf.h
   header, from Jesper.

4) When offloading to nfp JIT and the BPF insn is unsupported in the
   JIT, then reject right at verification time. Also fix libbpf with
   regards to ELF section name matching by properly treating the
   program type as prefix. Both from Quentin.

5) Add -DPACKAGE to bpftool when including bfd.h for the disassembler.
   This is needed, for example, when building libfd from source as
   bpftool doesn't supply a config.h for bfd.h. Fix from Jiong.

6) xdp_convert_ctx_access() is simplified since it doesn't need to
   set target size during verification, from Jesper.

7) Let bpftool properly recognize BPF_PROG_TYPE_CGROUP_DEVICE
   program types, from Roman.

8) Various functions in BPF cpumap were not declared static, from Wei.

9) Fix a double semicolon in BPF samples, from Luis.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull rdma fixes from Doug Ledford:
 "We had a few more items creep up over the last week. Given we are in
  -rc8, these are obviously limited to bugs that have a big downside and
  for which we are certain of the fix.

  The first is a straight up oops bug that all you have to do is read
  the code to see it's a guaranteed 100% oops bug.

  The second is a use-after-free issue. We get away lucky if the queue
  we are shutting down is empty, but if it isn't, we can end up oopsing.
  We really need to drain the queue before destroying it.

  The final one is an issue with bad user input causing us to access our
  port array out of bounds. While fixing the array out of bounds issue,
  it was noticed that the original code did the same thing twice (the
  call to rdma_ah_set_port_num()), so its removal is not balanced by a
  readd elsewhere, it was already where it needed to be in addition to
  where it didn't need to be.

  Summary:

   - Oops fix in hfi1 driver

   - use-after-free issue in iser-target

   - use of user supplied array index without proper checking"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
  RDMA/mlx5: Fix out-of-bound access while querying AH
  IB/hfi1: Prevent a NULL dereference
  iser-target: Fix possible use-after-free in connection establishment error

Jesper Dangaard Brouer says:

====================
This patchset contains some small improvements and cleanup for
the Makefile in tools/lib/bpf/.

It worries me that the libbpf.so shared library is not versioned,
but it not addressed in this patchset.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The third parameter to do_install was not used by $(INSTALL) command.
Fix this by only setting the -m option when the third parameter is supplied.

The use of a third parameter was introduced in commit  eb54e522 ("bpf:
install libbpf headers on 'make install'").

Without this change, the header files are install as executables files (755).

Fixes: eb54e522 ("bpf: install libbpf headers on 'make install'")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The plugin_dir_SQ variable is not used, remove it.
The function update_dir is also unused, remove it.
The variable $VERSION_FILES is empty, remove it.

These all originates from the introduction of the Makefile, and is likely a copy paste
from tools/lib/traceevent/Makefile.

Fixes: 1b76c13e ("bpf tools: Introduce 'bpf' library and add bpf feature check")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

It seems like an oversight not to install the header file for libbpf,
given the libbpf.so + libbpf.a files are installed.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Jakub Kicinski says:

====================
This series combines a number of random improvements ranging from
libbpf to nfp driver.  NFP patches make better use of the verifier
log.  There is a requested adjustment to the map offload code, and
a warning fix for a W=1 build to the disassembler.  Quentin also
fixes the libbpf program type detection, while Jiong allows the use
of libbfd compiled from source.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

If an eBPF instruction is unknown to the driver JIT compiler, we can
reject the program at verification time.
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Use the verifier log to output error messages if map lookup
can't be offloaded.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

libbpf is able to deduce the type of a program from the name of the ELF
section in which it is located. However, the comparison is made on the
first n characters, n being determined with sizeof() applied to the
reference string (e.g. "xdp"). When such section names are supposed to
receive a suffix separated with a slash (e.g. "kprobe/"), using sizeof()
takes the final NUL character of the reference string into account,
which implies that both strings must be equal. Instead, the desired
behaviour would consist in taking the length of the string, *without*
accounting for the ending NUL character, and to make sure the reference
string is a prefix to the ELF section name.

Subtract 1 to the total size of the string for obtaining the length for
the comparison.

Fixes: 583c9009 ("libbpf: add ability to guess program type based on section name")
Signed-off-by: NQuentin Monnet <quentin.monnet@netronome.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

bfd.h is requiring including of config.h except when PACKAGE or
PACKAGE_VERSION are defined.

  /* PR 14072: Ensure that config.h is included first.  */
  #if !defined PACKAGE && !defined PACKAGE_VERSION
  #error config.h must be included before this header
  #endif

This check has been introduced since May-2012. It doesn't show up in bfd.h
on some Linux distribution, probably because distributions have remove it
when building the package.

However, sometimes the user might just build libfd from source code then
link bpftool against it. For this case, bfd.h will be original that we need
to define PACKAGE or PACKAGE_VERSION.
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NJiong Wang <jiong.wang@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Functions of type bpf_insn_print_t take printf-like format
string, mark the type accordingly.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NQuentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Daniel suggests it would be more logical for bpf_offload_dev_match()
to return false is either the program or the map are not offloaded,
rather than treating the both not offloaded case as a "matching
CPU/host device".

This makes no functional difference today, since verifier only calls
bpf_offload_dev_match() when one of the objects is offloaded.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

The trailing semicolon is an empty statement that does no operation.
Removing it since it doesn't do anything.
Signed-off-by: NLuis de Bethencourt <luisbg@kernel.org>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Fixes the following sparse warnings:

kernel/bpf/cpumap.c:146:6: warning:
 symbol '__cpu_map_queue_destructor' was not declared. Should it be static?
kernel/bpf/cpumap.c:225:16: warning:
 symbol 'cpu_map_build_skb' was not declared. Should it be static?
kernel/bpf/cpumap.c:340:26: warning:
 symbol '__cpu_map_entry_alloc' was not declared. Should it be static?
kernel/bpf/cpumap.c:398:6: warning:
 symbol '__cpu_map_entry_free' was not declared. Should it be static?
kernel/bpf/cpumap.c:441:6: warning:
 symbol '__cpu_map_entry_replace' was not declared. Should it be static?
kernel/bpf/cpumap.c:454:5: warning:
 symbol 'cpu_map_delete_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:467:5: warning:
 symbol 'cpu_map_update_elem' was not declared. Should it be static?
kernel/bpf/cpumap.c:505:6: warning:
 symbol 'cpu_map_free' was not declared. Should it be static?
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Pull networking fixes from David Miller:

 1) Two read past end of buffer fixes in AF_KEY, from Eric Biggers.

 2) Memory leak in key_notify_policy(), from Steffen Klassert.

 3) Fix overflow with bpf arrays, from Daniel Borkmann.

 4) Fix RDMA regression with mlx5 due to mlx5 no longer using
    pci_irq_get_affinity(), from Saeed Mahameed.

 5) Missing RCU read locking in nl80211_send_iface() when it calls
    ieee80211_bss_get_ie(), from Dominik Brodowski.

 6) cfg80211 should check dev_set_name()'s return value, from Johannes
    Berg.

 7) Missing module license tag in 9p protocol, from Stephen Hemminger.

 8) Fix crash due to too small MTU in udp ipv6 sendmsg, from Mike
    Maloney.

 9) Fix endless loop in netlink extack code, from David Ahern.

10) TLS socket layer sets inverted error codes, resulting in an endless
    loop. From Robert Hering.

11) Revert openvswitch erspan tunnel support, it's mis-designed and we
    need to kill it before it goes into a real release. From William Tu.

12) Fix lan78xx failures in full speed USB mode, from Yuiko Oshino.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (54 commits)
  net, sched: fix panic when updating miniq {b,q}stats
  qed: Fix potential use-after-free in qed_spq_post()
  nfp: use the correct index for link speed table
  lan78xx: Fix failure in USB Full Speed
  sctp: do not allow the v4 socket to bind a v4mapped v6 address
  sctp: return error if the asoc has been peeled off in sctp_wait_for_sndbuf
  sctp: reinit stream if stream outcnt has been change by sinit in sendmsg
  ibmvnic: Fix pending MAC address changes
  netlink: extack: avoid parenthesized string constant warning
  ipv4: Make neigh lookup keys for loopback/point-to-point devices be INADDR_ANY
  net: Allow neigh contructor functions ability to modify the primary_key
  sh_eth: fix dumping ARSTR
  Revert "openvswitch: Add erspan tunnel support."
  net/tls: Fix inverted error codes to avoid endless loop
  ipv6: ip6_make_skb() needs to clear cork.base.dst
  sctp: avoid compiler warning on implicit fallthru
  net: ipv4: Make "ip route get" match iif lo rules again.
  netlink: extack needs to be reset each time through loop
  tipc: fix a memory leak in tipc_nl_node_get_link()
  ipv6: fix udpv6 sendmsg crash caused by too small MTU
  ...