Add cpsw phy sel device tree node for selecting phy mode in control module
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Both the VAR-STK-OM44 and VAR-DVK-OM44 boards comes with the
WLAN/BT version of the system on module VAR-SOM-OM44.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for VAR-SOM-OM44[1] SODIMM system on module from
Variscite. SoM features a OMAP4460, 1GB RAM, Gigabit Ethernet
(LAN7500) and optional WLAN/BT.

Also add support for VAR-STK-OM44 development board from
Variscite. This kit features a VAR-SOM-OM44 and the carrier board
VAR-OM44CustomBoard[2]. The VAR-STK-OM44 is the same as
VAR-DVK-OM44 but without the LCD display.

omap4-var-stk-om44.dts replace the old and very limited
omap4-var-som.dts.

[1] http://www.variscite.com/products/system-on-module-som/cortex-a9/var-som-om44-cpu-ti-omap-4-omap4460
[2] http://www.variscite.com/products/single-board-computers/var-om44customboardSigned-off-by: NJoachim Eastwood <manabian@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP4/5 TRMs primarily list address offsets from the padconf
physical address (which is not driver base address) and not
always the absolute physical address for padconf registers like
some other OMAP TRMs. So create a new macro to use this offset
and to avoid confusion between different OMAP parts.

For more information, see the tables in TRM for named something like
"Device Core Control Module Pad Configuration Register Fields"
and "Device Wake-Up Control Module Pad Configuration Register Fields"

Note that we now also have to update cm-t54 for the fixed up
offsets.
Signed-off-by: NJoachim Eastwood <manabian@gmail.com>
[tony@atomide.com: updated comments, updated cm-t54]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Make sure ethernet and mdio nodes are disabled by default and enable
them explicitly only on boards that actually use them.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add device tree nodes and pinmux for hdq/1wire on
am43x epos evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For SOCs with dt enabled, device should be build through device tree.
Prevent device build call from platform code, if device tree is
enabled.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add USB pinmux information and USB modes
for the USB controllers.

CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add nodes for the Super Speed USB controllers, omap-control-usb,
USB2 PHY and USB3 PHY devices.

Remove ocp2scp1 address space from hwmod data as it is
now provided via device tree.

CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This clock gate description is missing in the older Reference manuals.
It is present on the SoC to provide 960MHz reference clock to the
internal USB PHYs.

Reference: DRA75x_DRA74x_ES1.1_NDA_TRM_vO.pdf, pg. 900,
Table 3-812. CM_COREAON_L3INIT_60M_GFCLK_CLKCTRL

Use l3init_960m_gfclk as parent of usb_otg_ss1_refclk960m and
usb_otg_ss2_refclk960m.

CC: Benoît Cousson <bcousson@baylibre.com>
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The USB2 PHY driver expects named clocks for wakeup clock
and reference clock. Provide this information for USB2 PHY
nodes in OMAP4 and OMAP5 SoC DTS.

CC: Benoît Cousson <bcousson@baylibre.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add nodes for OCP2SCP3 bus, SATA controller and SATA PHY.

[Roger Q] Clean up. Updated IRQ for interrupt crossbar.

CC: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for sata.

[Roger Q] Clean up.

CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

In the comments, LCD pins 16-23 were numbered in the wrong order.
Fix this and use proper pinmux constants for all entries while we
are at it.
Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Cc: Benoit Parrot <bparrot@ti.com>
Tested-by: NDarren Etheridge <detheridge@ti.com>
[tony@atomide.com: updated description]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use MATRIX_KEY macro from dt-bindings/input/input.h
to make the keyboard matrix human readable.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These add device tree entry for qspi controller driver on dra7-evm.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VTT regulator for DDR3 termination on the am335x-evmsk is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The VTT regulator for DDR3 termination on the am437x-gp-evm is
controlled by a gpio. It is configured by the bootloader so here we
define an always-on, fixed voltage regulator to hold the gpio.
Signed-off-by: NDave Gerlach <d-gerlach@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add touchscreen support for AM437x GP EVM using pixcir
touchscreen controller.

CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fixup Y resolution and add default pin state. Also update
the compatible id.

CC: Benoit Cousson <bcousson@baylibre.com>
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use phandles instead of unit adresses to reference usb and dma nodes.
This makes the DT more robust and readable.
Signed-off-by: NGuido Martínez <guido@vanguardiasur.com.ar>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The only difference from the dra74x devices is the missing .smp entry.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use of const init definition must use __initconst so replace
all such instances where __initdata is used.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

DRA722 is part of DRA72x family which are single core cortex A15 devices
with most infrastructure IPs otherwise same as whats on the DRA74x family.

So move the cpu nodes into dra74x.dtsi and dra72x.dtsi respectively.

Also add a minimal dra72-evm dts file.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: linux-doc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: NArnd Bergmann <arnd@arndb.de>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: NTony Lindgren <tony@atomide.com>

"ti,dra752" is neither documented nor correct, since the device is actually a
dra742 device as rightly documented in dt bindings.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds qspi nodes for am43xx SOC devices.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support of AW-NH387 (mwifiex) WiFi/BT chip connected to MMC3.
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for CM-T54 CoM and SBC-T54 board:

http://compulab.co.il/products/computer-on-modules/cm-t54/
http://compulab.co.il/products/sbcs/sbc-t54/

SBC-T54 is a single board computer based on OMAP5432 CPU.
It is implemented with a CM-T54 CoM providing most of the functions,
and SB-T54 carrier board providing connectors and several additional
functions.

Added basic support for:

* PMIC
* LED
* MMC/SD
* eMMC
* USB
* I2C1/4
* SB-T54 and CM-T54 EEPROMs
* RTC
Signed-off-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
[tony@atomide.com: updated for Makefile sorting]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Expose the PMU on OMAP5.

Tested with perf on OMAP5 uEVM.
Signed-off-by: NNathan Lynch <nathan_lynch@mentor.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The N950/N9 uses two additional regulators from the twl 4030 for CSI-2
receiver (vaux2) and cameras (vaux3).
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for the Nokia N900's sound
system.
Signed-off-by: NSebastian Reichel <sre@kernel.org>
Reviewed-by: NMark Brown <broonie@linaro.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add madc node to twl4030, so that board DTS
files can simply reference the A/D converter.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add device tree support for the wireless chip
built into the Nokia N900.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable
	- USB PHY
	- USB

for am43x-epos-evm
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable
	- USB PHY
	- USB
for am437x-gp-evm
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>