Include local headers files after kernel's header files.
Signed-off-by: NHarish Patil <harish.patil@qlogic.com>
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For the Marvel 88e1111 PHY only two SGMII modes are available, both
allowing only SGMII to copper mode (with or without clock). SGMII
to fiber mode is not supported. Make sure the fiber/copper registers
selector bits are cleared for selecting copper mode.
Signed-off-by: NMadalin Bucur <madalin.bucur@freescale.com>
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we transmit a fragmented skb, we may run into a race like the
following scenario (assume txq->cur_tx is next to txq->dirty_tx):
           cpu 0                                          cpu 1
  fec_enet_txq_submit_skb
    reserve a bdp for the first fragment
    fec_enet_txq_submit_frag_skb
       update the bdp for the other fragment
       update txq->cur_tx
                                                   fec_enet_tx_queue
                                                     bdp = fec_enet_get_nextdesc(txq->dirty_tx, fep, queue_id);
                                                     This bdp is the bdp reserved for the first segment. Given
                                                     that this bdp BD_ENET_TX_READY bit is not set and txq->cur_tx
                                                     is already pointed to a bdp beyond this one. We think this is a
                                                     completed bdp and try to reclaim it.
    update the bdp for the first segment
    update txq->cur_tx

So we shouldn't update the txq->cur_tx until all the update to the
bdps used for fragments are performed. Also add the corresponding
memory barrier to guarantee that the update to the bdps, dirty_tx and
cur_tx performed in the proper order.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Store the length of the skb before transmitting it and use it for stats
instead of skb->len, since skb might have been freed already.

This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not use the length of the transmitted skb (which was freed), but
that of the response skb.

This issue was discovered using the Kernel Address sanitizer (KASan).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously we only checked if the transmission queue is not full in the
middle of the xmit function. This lead to complex logic due to the fact
that sometimes we need to reallocate the headroom for our Tx header.

Allow the switch driver to know if the transmission queue is not full
before sending the packet and remove this complex logic.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCS of incoming packets is already checked by HW. Just strip it out.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves compile errors on um-allyesconfig.

Note that there are many other drivers which have the same issue.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

System ports are unique identifiers in a multi-ASIC environment that
represent all the available ports in the system. Local ports on the
other hand, are unique only within the local ASIC.

Since system port to local port mapping is not part of the HW-SW
contract and since only single-ASIC configurations are currently
supported, set an explicit 1:1 mapping by configuring the Switch System
Port Record (SSPR) register.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing a port's netdevice we should also free the memory
allocated by alloc_etherdev(). Do this by calling free_netdev() at the
end of the teardown sequence.
Reported-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8211DN is compatible with RTL8211E.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a low level function for the ATU Load operation, and provide FDB add
and delete wrappers functions.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds a low level _mv88e6xxx_atu_getnext function and helpers
to rewrite the mv88e6xxx_port_fdb_getnext operation.

A mv88e6xxx_atu_entry structure is added for convenient access to the
hardware, and GLOBAL_ATU_FID is defined instead of the raw 0x01 value.

The previous implementation did not handle the eventual trunk mapping.
If the related bit is set, then the ATU data register would contain the
trunk ID, and not the port vector.

Check this in the FDB getnext operation and do not handle it (yet).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the __mv88e6xxx_{read,write}_addr functions to more explicit
_mv88e6xxx_atu_mac_{read,write} functions, which also respect the single
underscore convention used in the file (meaning SMI lock must be held).

In the meantime, define their MAC address parameters as an array of
ETH_ALEN bytes instead of a char pointer.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently manages one FID per port (or bridge group), with a
mask of DSA_MAX_PORTS bits, where 0 means that the FID is in use.

The Marvell 88E6xxx switches support up to 4094 FIDs (from 1 to 0xfff;
FID 0 means that multiple address databases are not being used).

This patch changes the fid_mask for an fid_bitmap of 4096 bits.

>From now on, FIDs 1 to num_ports are reserved for non-bridged ports and
bridge groups (a bridge group gets the FID of its first member). The
remaining bits will be reserved for VLAN entries.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the fdb_{add,del,getnext} function pointer in favor of new
port_fdb_{add,del,getnext}.

Implement the switchdev_port_obj_{add,del,dump} functions in DSA to
support the SWITCHDEV_OBJ_PORT_FDB objects.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The address in the switchdev_obj_fdb structure is currently represented
as a pointer. Replacing it for a 6-byte array allows switchdev to carry
addresses directly read from hardware registers, not stored by the
switch chip driver (as in Rocker).
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IFLA_VXLAN_FLOWBASED is useless without IFLA_VXLAN_COLLECT_METADATA,
so combine them into single IFLA_VXLAN_COLLECT_METADATA flag.
'flowbased' doesn't convey real meaning of the vxlan tunnel mode.
This mode can be used by routing, tc+bpf and ovs.
Only ovs is strictly flow based, so 'collect metadata' is a better
name for this tunnel mode.
Signed-off-by: NAlexei Starovoitov <ast@plumgrid.com>
Acked-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added physical port counters in the following standard formats to
ethtool statistics:
  - IEEE 802.3
  - RFC2863
  - RFC2819
Signed-off-by: NGal Pressman <galp@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that TIRs, TISs and flow tables are kept alive while the netdev is
stopped (after executing ndo_stop()) we can do the following
improvements:

- Obsolete the active_vlans SW shadow.
- Do not delete/add flow table rules upon ndo_stop/open.
  In addition to simplifying the flow, this change also fastens
  the ndo_open/close operations.
- Obsolete synchronization of threads accessing the flow tables
  with the netdev stop/open threads.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It does not make sense to allow events while the netdev is
unregistered.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename some functions that used to be invoked upon ndo_open/stop and
are now invoked upon create/destroy_netdev() in order to better hint
their place in the flow.

Change some functions location in the file so that functions involved
in ndo_open/stop flow will not be interleaved with other functions.

This is a cosmetic change, no logical change here.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create/destroy TIRs, TISs and flow tables upon PCI probe/remove rather
than upon the netdev ndo_open/stop.

Upon ndo_stop(), redirect all RX traffic to the (lately introduced)
"Drop RQ" and then close only the RX/TX rings, leaving the TIRs,
TISs and flow tables alive.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To be used by the mlx5 Eth driver in following commit.

This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX traffic routed to this RQ will be silently dropped, at the NIC HW
level.

This is in preparation for netdev "light-weight" open/stop flow
change described in previous commit.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generally an RX packet flows through the following objects:
Flow table --> TIR --> RQT --> RQ

Where:
- TIR stands for "Transport Interface Receive", defining the RSS and
  LRO paramaters.
- RQT stands for "RQ Table", implementing the RSS indirection table.
- RQ stands for "Receive Queue"

For flows that do not need LRO, nor RSS, the driver made a shortcut to
the above RX flow by pointing to the RQ directly from the TIR, yielding
this flow:
Flow table --> TIR --> RQ

In this commit we remove this shortcut by "inserting" a single-RQ RQT
between the TIR and the RQ, i.e RX packets will reach the same RQ but
will go through an RQT of size 1, pointing to just a single RQ.

This way the RX traffic re-direction to/from the "Drop RQ" will be more
uniform (AKA "one flow"), as it will involve only RQTs re-direction and
no TIRs re-direction.
Signed-off-by: NAchiad Shochat <achiad@mellanox.com>
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]

[1] http://patchwork.ozlabs.org/patch/492741/Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 230d00eb ("bnx2x: new Multi-function mode - BD") adds support
for the new mode in bnx2x. This expands this support by implementing
APIs required by our storage drivers to support that mode.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAdheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After successful register_netdev, we can use netdev_err rather the more
generic dev_err.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set port to NULL if port probe fails so we don't try to remove partially
initialized port on port probe err cleanup path.
Signed-off-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the algorithm. Read systimel twice and check for overflow.
If there was no overflow, use the first value.
If there was an overflow, read systimeh again and use the second
systimel value.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes wrong locking usage.
In the context of slot reset, we should use lock.
And during resume, there is no need of lock.
Reported-by: NBjorn Helgaas <bhelgaas@google.com>
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

1) Replace spaces with tab.
2) Move ich8lan related define to the proper context.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements the EEE in Sx code so that it only applies to parts
that support EEE in Sx (as opposed to all parts that support EEE).
It also uses the existing eee_advert and eee_lp_abiliity to set just the
bits (100/1000) that should be set.
Signed-off-by: NRaanan Avargil <raanan.avargil@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>