The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers.  Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register.  Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NJeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a reported compilation error where ia variable of type kuid_t
was being set to zero.

Eliminate two instances of setting tb->fastuid to zero.  tb->fastuid is
only used if tb->fastreuseport is set, so there should be no problem if
tb->fastuid is not initialized (when tb->fastreuesport is zero).
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 055dc21a (soreuseport: infrastructure) removed the #if 0
around SO_REUSEPORT without removing the corresponding #endif
thus causing the header guard to close early.

Cc: Tom Herbert <therbert@google.com>
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Providing communication channel between KVM and e-Switch so that it
can be informed when hypervisor configures a MAC address and VLAN.

qlcnic_mac_learn module param usage will be changed to:
	0 = MAC learning is disable
	1 = Driver learning is enable
	2 = FDB learning is enable
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

device eth0 entered promiscuous mode
BUG: sleeping function called from invalid context at mm/slub.c:930
in_atomic(): 1, irqs_disabled(): 0, pid: 5911, name: brctl
INFO: lockdep is turned off.
Pid: 5911, comm: brctl Tainted: GF       W  O 3.6.0-0.rc7.git1.4.fc18.x86_64 #1
Call Trace:
[<ffffffff810a29ca>] __might_sleep+0x18a/0x240
[<ffffffff811b5d77>] __kmalloc+0x67/0x2d0
[<ffffffffa00a61a9>] ? qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic]
[<ffffffffa00a61a9>] qlcnic_alloc_lb_filters_mem+0x59/0xa0 [qlcnic]
[<ffffffffa009e1c1>] qlcnic_set_multi+0x81/0x100 [qlcnic]
[<ffffffff8159cccf>] __dev_set_rx_mode+0x5f/0xb0
[<ffffffff8159cd4f>] dev_set_rx_mode+0x2f/0x50
[<ffffffff8159d00c>] dev_set_promiscuity+0x3c/0x50
[<ffffffffa05ed728>] br_add_if+0x1e8/0x400 [bridge]
[<ffffffffa05ee2df>] add_del_if+0x5f/0x90 [bridge]
[<ffffffffa05eee0b>] br_dev_ioctl+0x4b/0x90 [bridge]
[<ffffffff8159d613>] dev_ifsioc+0x373/0x3b0
[<ffffffff8159d78f>] dev_ioctl+0x13f/0x860
[<ffffffff812dd6e1>] ? avc_has_perm_flags+0x31/0x2c0
[<ffffffff8157c18d>] sock_do_ioctl+0x5d/0x70
[<ffffffff8157c21d>] sock_ioctl+0x7d/0x2c0
[<ffffffff812df922>] ? inode_has_perm.isra.48.constprop.61+0x62/0xa0
[<ffffffff811e4979>] do_vfs_ioctl+0x99/0x5a0
[<ffffffff812df9f7>] ? file_has_perm+0x97/0xb0
[<ffffffff810d716d>] ? trace_hardirqs_on+0xd/0x10
[<ffffffff811e4f19>] sys_ioctl+0x99/0xa0
[<ffffffff816e7369>] system_call_fastpath+0x16/0x1b
br0: port 1(eth0) entered forwarding state
br0: port 1(eth0) entered forwarding state
Signed-off-by: NJitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide port number in command payload for LED/Beaconing tests.
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o Some adapter types do not support co-existence of Legacy Interrupt with
  MSI-x or MSI among multiple functions. For those adapters, prevent attaching
  to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
  legacy mode for all functions in the adapter.
Signed-off-by: NManish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6
Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NShahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
This batch contains netfilter updates for you net-next tree, they are:

* The new connlabel extension for x_tables, that allows us to attach
  labels to each conntrack flow. The kernel implementation uses a
  bitmask and there's a file in user-space that maps the bits with the
  corresponding string for each existing label. By now, you can attach
  up to 128 overlapping labels. From Florian Westphal.

* A new round of improvements for the netns support for conntrack.
  Gao feng has moved many of the initialization code of each module
  of the netns init path. He also made several code refactoring, that
  code looks cleaner to me now.

* Added documentation for all possible tweaks for nf_conntrack via
  sysctl, from Jiri Pirko.

* Cisco 7941/7945 IP phone support for our SIP conntrack helper,
  from Kevin Cernekee.

* Missing header file in the snmp helper, from Stephen Hemminger.

* Finally, a couple of fixes to resolve minor issues with these
  changes, from myself.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The X540 can link at 100Mbps - fix the link speed indicator message to
show that value.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63.  Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: NDonald Dutile <ddutile@redhat.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally.  Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to inline the Rx PTP descriptor handling.  The main
motivation is to avoid unnecessary jumps into function calls that we then
immediately exit because we are not performing timestamps.

The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU
utilization in my performance runs to 0%, and the only value tested is the Rx
descriptor which should already be warm in the cache if not stored in a
register.

Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJacob Keller <Jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.

This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: NMatthew Vick <matthew.vick@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.

To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.

If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Steffen Klassert says:

====================
1) Add a statistic counter for invalid output states and
   remove a superfluous state valid check, from Li RongQing.

2) Probe for asynchronous block ciphers instead of synchronous block
   ciphers to make the asynchronous variants available even if no
   synchronous block ciphers are found, from Jussi Kivilinna.

3) Make rfc3686 asynchronous block cipher and make use of
   the new asynchronous variant, from Jussi Kivilinna.

4) Replace some rwlocks by rcu, from Cong Wang.

5) Remove some unused defines.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When posting a message on the bulletin board, the PF calculates crc
over the message and places the result in the message. When the VF
samples the Bulletin Board it copies the message aside and validates
this crc. The length of the message is crucial here and must be the
same in both parties. Since the PF is running in the Hypervisor and
the VF is running in a Vm, they can possibly be of different versions.
As the Bulletin Board is designed to grow forward in future versions,
in the VF the length must not be the size of the message structure
but instead it should be a field in the message itself.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 823e1d90 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set.
Fixes compilation by moving function declarations between header files.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In INTA mode, cnic and bnx2x share the same IRQ.  During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources.  However, the shared IRQ is still active as
bnx2x needs to finish the reset.  There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.

Add a flag to tell bnx2x that cnic is handling IRQ.  The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix an incorrect SR-IOV memory release which was committed in 1ab4434c.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't unload the bnx2x driver if its in a recovery process, or if
the previous load have failed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 15192a8c there have been a memory leak upon rmmod
of the bnx2x driver.

This corrects the memory leak and corrects the zeroing of internal
memories upon driver load.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3
macros (missing from commit 8395be5e).
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slightly changes the bnx2x code without `true' functional changes.
Changes include:
 1. Gathering macros into a single macro when combination is used multiple
    times.
 2. Exporting parts of functions into their own functions.
 3. Return values after if-else instead of only on the else condition
    (where current flow would simply return same value later in the code)
 4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly corrects white spaces, indentations, and comments.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>