- 24 4月, 2008 22 次提交
-
-
由 Clemens Ladisch 提交于
Fix the GPIO 1 mixer control to enable I/O through the front panel connector of the Xonar DX. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
On the Xonar DX, initialize all bits of the two-wire control register. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Add a mixer control for switching whatever it is that is connected to GPIO pin 1 on the Xonar DX. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
If the card model does not have a digital input or an AC97 codec, disable the respective interrupt and mixer controls. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
When selecting the capture source on the Xonar DX, the input jack must be routed to either the line input or the microphone input by setting a GPIO pin. This requires an additional callback so that the model driver can hook into the toggling of AC97 switches. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Add support for the Asus Xonar DX. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Fix a (fortunately harmless) typo. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Change the card short name to show to show the card name instead of the chip name. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
When playing data at 96 kHz or higher, reduce the DAC oversampling rate to 32. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Move the code that is common to all Xonar models to a separate function, and make it more generic in preparation for another model. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Rename all CS5381 symbols to CS53x1 because they can also be used for Xonar models with a CS5361. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Use separate model structures for the D2 and D2X so that the init function does not have to check for the model again. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Add a function to write I2C registers. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
On C-Media cards, the GPIO pin 0 of the CM9780 must be handled exactly like on Xonar cards, so move the Xonar code to the common mixer code. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Disable the master clock outputs of any unused I2S inputs. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Put the flag that enables the MIDI port into the model structure instead of passing it as a separate parameter to oxygen_pci_probe(). Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Allow the model drivers to specify if the codec communication goes over SPI or a 2-wire bus. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
When specifying which PCM devices to use, model drivers now use flags that also specify the routing between PCM devices and DMA channels instead of just DMA channel bits. This simplifies some code that checks for these flags. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Add controls to enable monitoring of the analog and digital inputs. To allow monitoring after loading the driver when nothing has been played back or recorded yet, the I2S input and outputs are initialized to a valid configuration. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Move the PCM1796 register symbol definitions to their own header file. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Clemens Ladisch 提交于
Move the WM8786 register symbol definitions to their own header file. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
由 Harvey Harrison 提交于
Use priv_idx as an identifier. sound/pci/oxygen/virtuoso.c:277:15: warning: symbol 'index' shadows an earlier one sound/pci/oxygen/virtuoso.c:56:12: originally declared here Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 29 2月, 2008 1 次提交
-
-
由 Clemens Ladisch 提交于
I forgot to set the module owner for the HiFier/Xonar models. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de>
-
- 23 2月, 2008 2 次提交
-
-
由 Clemens Ladisch 提交于
The GPIO pin 0 of the CM9780 must be set when muting the line input even on non-Xonar cards. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Takashi Iwai 提交于
Removed invalid __devinit and __devexit that are remaining after split to a helper module. Signed-off-by: NTakashi Iwai <tiwai@suse.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 01 2月, 2008 15 次提交
-
-
由 Clemens Ladisch 提交于
While the AK4396 and WM8785 datasheets say that the SPI clock cycle length must be at least 200 ns, 320 ns seems not to work reliably with the controller, so we better use 160 ns. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
On the Xonar D2X, monitor the GPIO pin that indicates whether external power is present. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
When a second AC97 codec is present, add a PCM device for capturing from the front panel. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Add mixer controls for the front panel AC97 codec. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
After an AC97 register read or write, use the AC97 interrupt instead of polling to wait for the access to be completed. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Move the line input switching code to the Virtuoso driver because only the Xonar cards bypass the analog mixer for line input. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Fix the upper sample rate limit for the double rate mode of the AK4396 to the value from the datasheet. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Add a driver for the MediaTek/TempoTec HiFier Fantasia sound card. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Initialize more registers of the controller and the second AC97 codec. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Add a field to struct oxygen_model to allow model drivers for cards with less than eight output channels. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
None of the reference design models have MIDI, only the X-Meridian allows to connect a MIDI adapter. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Fix up SPDIF input sample rates again: 32 kHz and 64 kHz are not supported. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Add a mixer control for the SPDIF loopback function. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Add one more indirection to the lookup of the snd_pcm_hardware structures so that we can save the space of the duplicate ones. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-
由 Clemens Ladisch 提交于
Change the oxygen_spdif_input_bits_changed() function so that clock changes on the SPDIF input are correctly detected. This means that sample rates greater than 96 kHz are now supported. Signed-off-by: NClemens Ladisch <clemens@ladisch.de> Signed-off-by: NJaroslav Kysela <perex@perex.cz>
-