Florian Fainelli says:

====================
net: bcmgenet: misc fixes

This patch series contains some misc. fixes for the bcmgenet driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of always invoking netdev_get_tx_queue() in bcmgenet_xmit() and
bcmgenet_tx_reclaim(), just get the corresponding netdev_queue pointer
once and for all and manipulate it throughout bcmgenet_xmit() and
bcmgenet_tx_reclaim().
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev_pick_tx already takes care of making sure that a given
skb->queue_mapping value will remain within the number of advertised
hardware queue number, there is no need to re-do this again in the
driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The BCMGENET driver was not TX timestamping the SKBs it queued for
transmission, do this in bcmgenet_xmit() right before kicking the
Transmit DMA engine.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The spinlock cookie in bcmgenet_priv is never used, get rid of it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Laurent Pinchart says:

====================
sh_eth: Fix the race between open and MDIO bus registration

This patch series fixes the race condition that exists in the sh_eth driver
between network device open and MDIO bus registration. The actual fix is in
patch 4/5, with previous patches preparing the driver and patch 5/5 cleaning
up an unrelated issue.

I've based the idea on Sergei's attempt to fix the problem and can successfully
boot the Koelsch board over NFS with this series. I might have missed other
issues though, hence the RFC status.

The patches are based on top of the latest net-next master branch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"goto" is well accepted for error paths in the kernel but should not be
used unnecessarily. Return the correct value directly instead of using a
goto when possible.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Network API functions that rely on the MDIO bus can be called as soon as
the driver calls register_netdev(). Register the MDIO bus before the
network device to avoid race conditions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The network device passed to the sh_mdio_init and sh_mdio_release
functions is only used to access the sh_eth_private instance. Pass it
directly to those functions.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO bus parent is set to the network device. Beside not reflecting
the hardware topology, this prevents registering the MDIO bus before
initializing the network device. Fix it by setting the MDIO bus parent
to the platform device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Memory allocated for the MDIO bus with the devm_kzalloc() API is
associated with the network device. While this will cause memory to be
freed at the right time, it doesn't allow allocating memory before the
network device is initialized.

Replace the network device with the parent platform device for memory
allocation to remove that dependency. This also improves consistency
with the other devm_* calls in the driver that all use the platform
device.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is only a cleanup to use the right define for a panid field.
The broadcast address and panid broadcast is still the same value.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue which was introduced by commit
b70ab2e8 ("ieee802154: enforce
consistent endianness in the 802.15.4 stack").

The correct behaviour should be a check on the broadcast address field
which is 0xffff.
Signed-off-by: NAlexander Aring <alex.aring@gmail.com>
Reported-by: NJan Luebbe <jlu@pengutronix.de>
Cc: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This makes the generic of_mdiobus_register parse the DT compatible string for
the pattern ethernet-phy-idAAAA.BBBB. If present it should be a value that
matches the phy-id register normally readable through MDIO.

When the ID is given the phy autoprobing is defeated and the phy is
created directly.

This is necessary to support phy's that cannot be autoprobed when
of_mdiobus_register is called. Specifically, my case has the phy in reset at
of_mdiobus_register, the reset is only released once the ethernet driver
starts, before it attaches to the phy.

Tested on ARM Kirkwood with phy id 0x01410e90 (Marvell 88E1318)
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This describes a compatible entry of the form:
  ethernet-phy-idAAAA,BBBB
Which is modelled after the PCI structured compatible entry
(pciVVVV,DDDD.SSSS.ssss.RR)

If present the OF core will be able to use this information to
directly create the correct phy without auto probing the bus.
Signed-off-by: NJason Gunthorpe <jgunthorpe@obsidianresearch.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ben Chan says:

====================
Adjust MTU as indicated by MBIM extended functional descriptor.

The MBIM extended functional descriptor, defined in "Universal Serial Bus
Communications Class Subclass Specification for Mobile Broadband Interface
Model, Revision 1.0, Errata-1" by USB-IF, indicates the operator preferred MTU
value via a wMTU field.

This patch set ensures that the initial MTU value set by cdc_ncm on a MBIM net
device does not exceed the wMTU value, provided the MBIM device exposes a MBIM
extended functional descriptor.

* Changelog
v2: Fixed a le16_to_cpu conversion issue in patch 2/2 pointed out by
    Bjørn Mork <bjorn@mork.no>
v3: No code changes. Resubmitted to include patch 1/2 as suggested by
    David Miller <davem@davemloft.net>
v4: No code changes. Resubmitted as suggested by David Miller:
    - Added a summary of the patch set
    - Carried the ACK from Greg Kroah-Hartman <gregkh@linuxfoundation.org>
    - Added a specified the tree (net-next) to apply the patch set to
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF, the wMTU field of the MBIM extended
functional descriptor indicates the operator preferred MTU for IP data
streams.

This patch modifies cdc_ncm_setup to ensure that the MTU value set on
the usbnet device does not exceed the operator preferred MTU indicated
by wMTU if the MBIM device exposes a MBIM extended functional
descriptor.
Signed-off-by: NBen Chan <benchan@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the MBIM extended functional descriptor structure
defined in "Universal Serial Bus Communications Class Subclass
Specification for Mobile Broadband Interface Model, Revision 1.0,
Errata-1" published by USB-IF.
Signed-off-by: NBen Chan <benchan@chromium.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Or Gerlitz says:

====================
mlx4: Add support for single port VFs

The mlx4 Firmware && driver expose both ports of the device through one PCI function.

This can be non-optimal under virtualization schemes where the admin
would like the VF to expose one interface to the VM, etc.

This series from Matan Barak adds support for single ported VFs.

Since all the VF interaction with the firmware passes through the PF
 driver, we can emulate to the VF they have one port, and further create
a set of the VFs which act on port1 of the device and another set which
acts on port2.

Series done against net-next commit 3ab428a4 "netfilter: Add missing
vmalloc.h include to nft_hash.c"

Roland, we send this through netdev, but if you have comments, will love
to hear them.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A new syntax is added for the module parameters num_vfs and probe_vf.

  num_vfs=p1,p2,p1+p2
  probe_bf=p1,p2,p1+p2

Where p1(2) is the number of VFs on / probed VFs for physical
port1(2) and p1+p2 is the number of dual port VFs.

Single port VFs are currently supported only when the link type
for both ports of the device is Ethernet.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for N-Port VFs, this includes:
1. Adding support in the wrapped FW command
	In wrapped commands, we need to verify and convert
	the slave's port into the real physical port.
	Furthermore, when sending the response back to the slave,
	a reverse conversion should be made.
2. Adjusting sqpn for QP1 para-virtualization
	The slave assumes that sqpn is used for QP1 communication.
	If the slave is assigned to a port != (first port), we need
	to adjust the sqpn that will direct its QP1 packets into the
	correct endpoint.
3. Adjusting gid[5] to modify the port for raw ethernet
	In B0 steering, gid[5] contains the port. It needs
	to be adjusted into the physical port.
4. Adjusting number of ports in the query / ports caps in the FW commands
	When a slave queries the hardware, it needs to view only
	the physical ports it's assigned to.
5. Adjusting the sched_qp according to the port number
	The QP port is encoded in the sched_qp, thus in modify_qp we need
	to encode the correct port in sched_qp.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the following utils:
1. Convert slave_id -> VF
2. Get the active ports by slave_id
3. Convert slave's port to real port
4. Get the slave's port from real port
5. Get all slaves that uses the i'th real port
6. Get all slaves that uses the i'th real port exclusively
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds the required data structures to support VFs with N (1 or 2)
ports instead of always using the number of physical ports.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some code in the mlx4 IB driver stack assumed MLX4_MAX_PORTS ports.

Instead, we should only loop until the number of actual ports in i
the device, which is stored in dev->caps.num_ports.
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:

smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDaniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.

Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.

Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.

Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it.  Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.

Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link.  Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.

Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up.  To resolve this, move the call to enable Tx
queues to after the link is established.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.

In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check.  This patch makes that
change.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.

This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.

Reverts: 4e8e1bca ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.

This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.

CC: Arun Sharma <asharma@fb.com>
Reported-by: NSourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.

CC: Arun Sharma <asharma@fb.com>
Reported-by: NChris Pavlas <chris.pavlas@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it.   This would lead to DA cables being unable to link along with
possible other errors.

CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>