commit aa57157be69fb599bd4c38a4b75c5aad74a60ec0 upstream.

Shared and writable mappings (__S.1.) should be clean (!dirty) initially
and made dirty on a subsequent write either through the hardware DBM
(dirty bit management) mechanism or through a write page fault. A clean
pte for the arm64 kernel is one that has PTE_RDONLY set and PTE_DIRTY
clear.

The PAGE_SHARED{,_EXEC} attributes have PTE_WRITE set (PTE_DBM) and
PTE_DIRTY clear. Prior to commit 73e86cb0 ("arm64: Move PTE_RDONLY
bit handling out of set_pte_at()"), it was the responsibility of
set_pte_at() to set the PTE_RDONLY bit and mark the pte clean if the
software PTE_DIRTY bit was not set. However, the above commit removed
the pte_sw_dirty() check and the subsequent setting of PTE_RDONLY in
set_pte_at() while leaving the PAGE_SHARED{,_EXEC} definitions
unchanged. The result is that shared+writable mappings are now dirty by
default

Fix the above by explicitly setting PTE_RDONLY in PAGE_SHARED{,_EXEC}.
In addition, remove the superfluous PTE_DIRTY bit from the kernel PROT_*
attributes.

Fixes: 73e86cb0 ("arm64: Move PTE_RDONLY bit handling out of set_pte_at()")
Cc: <stable@vger.kernel.org> # 4.14.x-
Cc: Will Deacon <will@kernel.org>
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 3d7efa4edd07be5c5c3ffa95ba63e97e070e1f3f upstream.

The idle time reported in /proc/stat sometimes incorrectly contains
huge values on s390. This is caused by a bug in arch_cpu_idle_time().

The kernel tries to figure out when a different cpu entered idle by
accessing its per-cpu data structure. There is an ordering problem: if
the remote cpu has an idle_enter value which is not zero, and an
idle_exit value which is zero, it is assumed it is idle since
"now". The "now" timestamp however is taken before the idle_enter
value is read.

Which in turn means that "now" can be smaller than idle_enter of the
remote cpu. Unconditionally subtracting idle_enter from "now" can thus
lead to a negative value (aka large unsigned value).

Fix this by moving the get_tod_clock() invocation out of the
loop. While at it also make the code a bit more readable.

A similar bug also exists for show_idle_time(). Fix this is as well.

Cc: <stable@vger.kernel.org>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b8e51a6a9db94bc1fb18ae831b3dab106b5a4b5f upstream.

The problem is that we were putting the NUL terminator too far:

	buf[sizeof(buf) - 1] = '\0';

If the user input isn't NUL terminated and they haven't initialized the
whole buffer then it leads to an info leak.  The NUL terminator should
be:

	buf[len - 1] = '\0';
Signed-off-by: NYihui Zeng <yzeng56@asu.edu>
Cc: stable@vger.kernel.org
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
[heiko.carstens@de.ibm.com: keep semantics of how *lenp and *ppos are handled]
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1fab1b89e2e8f01204a9c05a39fd0b6411a48593 upstream.

Mesh path nexthop should be a ethernet address, but current validation
checks against 4 byte integers.

Cc: stable@vger.kernel.org
Fixes: 2ec600d6 ("nl80211/cfg80211: support for mesh, sta dumping")
Signed-off-by: NMarkus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20191029093003.10355-1-markus.theil@tu-ilmenau.deSigned-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b3a81c777dcb093020680490ab970d85e2f6f04f upstream.

On HID report descriptor parsing error the code displays bogus
pointer instead of error offset (subtracts start=NULL from end).
Make the message more useful by displaying correct error offset
and include total buffer size for reference.

This was carried over from ancient times - "Fixed" commit just
promoted the message from DEBUG to ERROR.

Cc: stable@vger.kernel.org
Fixes: 8c3d52fc ("HID: make parser more verbose about parsing errors by default")
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d9d4b1e46d9543a82c23f6df03f4ad697dab361b upstream.

The syzbot fuzzer found a slab-out-of-bounds write bug in the hid-gaff
driver.  The problem is caused by the driver's assumption that the
device must have an input report.  While this will be true for all
normal HID input devices, a suitably malicious device can violate the
assumption.

The same assumption is present in over a dozen other HID drivers.
This patch fixes them by checking that the list of hid_inputs for the
hid_device is nonempty before allowing it to be used.

Reported-and-tested-by: syzbot+403741a091bf41d4ae79@syzkaller.appspotmail.com
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 09f3dbe474735df13dd8a66d3d1231048d9b373f upstream.

The Primebook C11B uses the SIPODEV SP1064 touchpad. There are 2 versions
of this 2-in-1 and the touchpad in the older version does not supply
descriptors, so it has to be added to the override list.

Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit fc5b220b2dcf8b512d9bd46fd17f82257e49bf89 upstream.

Use the pointer 'p' after having tested that pointer instead of before.

Fixes: 5cadafb2 ("target/cxgbit: Fix endianness annotations")
Cc: Varun Prakash <varun@chelsio.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191023202150.22173-1-bvanassche@acm.orgReported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 84968291d7924261c6a0624b9a72f952398e258b upstream.

Add missing endianness conversion when setting the line speed so that
this driver might work also on big-endian machines.

Also use an unsigned format specifier in the corresponding debug
message.
Signed-off-by: NJohan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-3-johan@kernel.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1251dab9e0a2c4d0d2d48370ba5baa095a5e8774 upstream.

Fix a user-controlled slab buffer overflow due to a missing sanity check
on the bulk-out transfer buffer used for control requests.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191029102354.2733-2-johan@kernel.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d5501d5c29a2e684640507cfee428178d6fd82ca upstream.

It looks like some of the xhci debug code is passing u32 to functions
directly from __le32/__le64 fields.
Fix this by using le{32,64}_to_cpu() on these to fix the following
sparse warnings;

xhci-debugfs.c:205:62: warning: incorrect type in argument 1 (different base types)
xhci-debugfs.c:205:62:    expected unsigned int [usertype] field0
xhci-debugfs.c:205:62:    got restricted __le32
xhci-debugfs.c:206:62: warning: incorrect type in argument 2 (different base types)
xhci-debugfs.c:206:62:    expected unsigned int [usertype] field1
xhci-debugfs.c:206:62:    got restricted __le32
...

[Trim down commit message, sparse warnings were similar -Mathias]
Cc: <stable@vger.kernel.org> # 4.15+
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/1572013829-14044-4-git-send-email-mathias.nyman@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 52403cfbc635d28195167618690595013776ebde upstream.

USB control-message timeouts are specified in milliseconds, not jiffies.
Waiting 83 minutes for a transfer to complete is a bit excessive.

Fixes: 2824bd25 ("[PATCH] USB: add ldusb driver")
Cc: stable <stable@vger.kernel.org>     # 2.6.13
Reported-by: syzbot+a4fbb3bb76cda0ea4e58@syzkaller.appspotmail.com
Signed-off-by: NJohan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022153127.22295-1-johan@kernel.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit d98ee2a19c3334e9343df3ce254b496f1fc428eb upstream.

The custom ring-buffer implementation was merged without any locking or
explicit memory barriers, but a spinlock was later added by commit
9d33efd9 ("USB: ldusb bugfix").

The lock did not cover the update of the tail index once the entry had
been processed, something which could lead to memory corruption on
weakly ordered architectures or due to compiler optimisations.

Specifically, a completion handler running on another CPU might observe
the incremented tail index and update the entry before ld_usb_read() is
done with it.

Fixes: 2824bd25 ("[PATCH] USB: add ldusb driver")
Fixes: 9d33efd9 ("USB: ldusb bugfix")
Cc: stable <stable@vger.kernel.org>     # 2.6.13
Signed-off-by: NJohan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191022143203.5260-2-johan@kernel.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

usb-storage: Revert commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")

commit 9a976949613132977098fc49510b46fa8678d864 upstream.

Commit 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG
overflows") attempted to solve a problem involving scatter-gather I/O
and USB/IP by setting the virt_boundary_mask for mass-storage devices.

However, it now turns out that this interacts badly with commit
09324d32d2a0 ("block: force an unlimited segment size on queues with a
virt boundary"), which was added later.  A typical error message is:

	ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
	total 32768 (slots), used 97 (slots)

There is no longer any reason to keep the virt_boundary_mask setting
for usb-storage.  It was needed in the first place only for handling
devices with a block size smaller than the maxpacket size and where
the host controller was not capable of fully general scatter-gather
operation (that is, able to merge two SG segments into a single USB
packet).  But:

	High-speed or slower connections never use a bulk maxpacket
	value larger than 512;

	The SCSI layer does not handle block devices with a block size
	smaller than 512 bytes;

	All the host controllers capable of SuperSpeed operation can
	handle fully general SG;

	Since commit ea44d190764b ("usbip: Implement SG support to
	vhci-hcd and stub driver") was merged, the USB/IP driver can
	also handle SG.

Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask.  So in order to fix
the swiotlb problem, this patch reverts commit 747668dbc061.
Reported-and-tested-by: NPiergiorgio Sartor <piergiorgio.sartor@nexgo.de>
Link: https://marc.info/?l=linux-usb&m=157134199501202&w=2Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Seth Bollinger <Seth.Bollinger@digi.com>
CC: <stable@vger.kernel.org>
Fixes: 747668dbc061 ("usb-storage: Set virt_boundary_mask to avoid SG overflows")
Acked-by: NChristoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910211145520.1673-100000@iolanthe.rowland.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 54f83b8c8ea9b22082a496deadf90447a326954e upstream.

Endpoints with a maxpacket length of 0 are probably useless.  They
can't transfer any data, and it's not at all unlikely that a UDC will
crash or hang when trying to handle a non-zero-length usb_request for
such an endpoint.  Indeed, dummy-hcd gets a divide error when trying
to calculate the remainder of a transfer length by the maxpacket
value, as discovered by the syzbot fuzzer.

Currently the gadget core does not check for endpoints having a
maxpacket value of 0.  This patch adds a check to usb_ep_enable(),
preventing such endpoints from being used.

As far as I know, none of the gadget drivers in the kernel tries to
create an endpoint with maxpacket = 0, but until now there has been
nothing to prevent userspace programs under gadgetfs or configfs from
doing it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: syzbot+8ab8bf161038a8768553@syzkaller.appspotmail.com
CC: <stable@vger.kernel.org>
Acked-by: NFelipe Balbi <balbi@kernel.org>
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910281052370.1485-100000@iolanthe.rowland.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 1186f86a71130a7635a20843e355bb880c7349b2 upstream.

Commit 3ae62a42090f ("UAS: fix alignment of scatter/gather segments"),
copying a similar commit for usb-storage, attempted to solve a problem
involving scatter-gather I/O and USB/IP by setting the
virt_boundary_mask for mass-storage devices.

However, it now turns out that the analogous change in usb-storage
interacted badly with commit 09324d32d2a0 ("block: force an unlimited
segment size on queues with a virt boundary"), which was added later.
A typical error message is:

	ehci-pci 0000:00:13.2: swiotlb buffer is full (sz: 327680 bytes),
	total 32768 (slots), used 97 (slots)

There is no longer any reason to keep the virt_boundary_mask setting
in the uas driver.  It was needed in the first place only for
handling devices with a block size smaller than the maxpacket size and
where the host controller was not capable of fully general
scatter-gather operation (that is, able to merge two SG segments into
a single USB packet).  But:

	High-speed or slower connections never use a bulk maxpacket
	value larger than 512;

	The SCSI layer does not handle block devices with a block size
	smaller than 512 bytes;

	All the host controllers capable of SuperSpeed operation can
	handle fully general SG;

	Since commit ea44d190764b ("usbip: Implement SG support to
	vhci-hcd and stub driver") was merged, the USB/IP driver can
	also handle SG.

Therefore all supported device/controller combinations should be okay
with no need for any special virt_boundary_mask.  So in order to head
off potential problems similar to those affecting usb-storage, this
patch reverts commit 3ae62a42090f.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oneukum@suse.com>
CC: <stable@vger.kernel.org>
Acked-by: NChristoph Hellwig <hch@lst.de>
Fixes: 3ae62a42090f ("UAS: fix alignment of scatter/gather segments")
Link: https://lore.kernel.org/r/Pine.LNX.4.44L0.1910231132470.1878-100000@iolanthe.rowland.orgSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f0778871a13889b86a65d4ad34bef8340af9d082 upstream.

Support new codec ALC623.
Signed-off-by: NKailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/ed97b6a8bd9445ecb48bc763d9aaba7a@realtek.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit 8a6c55d0f883e9a7e7c91841434f3b6bbf932bb2 upstream.

These 2 ThinkCentres installed a new realtek codec ID 0x623,
it has 2 front mics with the same location on pin 0x18 and 0x19.

Apply fixup ALC283_FIXUP_HEADSET_MIC to change 1 front mic
location to right, then pulseaudio can handle them.
One "Front Mic" and one "Mic" will be shown, and audio output works
fine.
Signed-off-by: NAaron Ma <aaron.ma@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191024114439.31522-1-aaron.ma@canonical.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit f2bbdbcb075f3977a53da3bdcb7cd460bc8ae5f2 upstream.

A helper function of ALSA bebob driver returns negative value in a
function which has a prototype to return unsigned value.

This commit fixes it by changing the prototype.

Fixes: eb7b3a05 ("ALSA: bebob: Add commands and connections/streams management")
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20191026030620.12077-1-o-takashi@sakamocchi.jpSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit e4648309b85a78f8c787457832269a8712a8673e upstream.

Make sure cached writes are not reordered around open(..., O_TRUNC), with
the obvious wrong results.

Fixes: 4d99ff8f ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

commit b24e7598db62386a95a3c8b9c75630c5d56fe077 upstream.

If writeback cache is enabled, then writes might get reordered with
chmod/chown/utimes.  The problem with this is that performing the write in
the fuse daemon might itself change some of these attributes.  In such case
the following sequence of operations will result in file ending up with the
wrong mode, for example:

  int fd = open ("suid", O_WRONLY|O_CREAT|O_EXCL);
  write (fd, "1", 1);
  fchown (fd, 0, 0);
  fchmod (fd, 04755);
  close (fd);

This patch fixes this by flushing pending writes before performing
chown/chmod/utimes.
Reported-by: NGiuseppe Scrivano <gscrivan@redhat.com>
Tested-by: NGiuseppe Scrivano <gscrivan@redhat.com>
Fixes: 4d99ff8f ("fuse: Turn writeback cache on")
Cc: <stable@vger.kernel.org> # v3.15+
Signed-off-by: NMiklos Szeredi <mszeredi@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

[ Upstream commit 39d170b3cb62ba98567f5c4f40c27b5864b304e5 ]

The `ar_usb` field of `ath6kl_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath6kl_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath6kl_usb_setup_pipe_resources`:

for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
	endpoint = &iface_desc->endpoint[i].desc;

	// get the address from endpoint descriptor
	pipe_num = ath6kl_usb_get_logical_pipe_num(ar_usb,
						endpoint->bEndpointAddress,
						&urbcount);
	......
	// select the pipe object
	pipe = &ar_usb->pipes[pipe_num];

	// initialize the ar_usb field
	pipe->ar_usb = ar_usb;
}

The driver assumes that the addresses reported in endpoint
descriptors from device side  to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath6kl_usb_alloc_urb_from_pipe` and
`ath6kl_usb_free_urb_to_pipe`.

This patch fixes the bug by preventing potential NULL-ptr-deref
(CVE-2019-15098).
Signed-off-by: NHui Peng <benquike@gmail.com>
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 943795219d3cb9f8ce6ce51cad3ffe1f61e95c6b ]

The register access should be using 32-bit reads/writes according to the
datasheet. With the previous generation hardware 16-bit writes have been
working but starting with ICL this is not the case anymore so fix
producer/consumer register update to use correct width register address.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NYehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: NMario Limonciello <mario.limonciello@dell.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fd47a417e75e2506eb3672ae569b1c87e3774155 ]

The problem is that sizeof() is unsigned long so negative error codes
are type promoted to high positive values and the condition becomes
false.

Fixes: 1d427be4a39d ("USB: legousbtower: fix slab info leak at probe")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20191011141115.GA4521@mwandaSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cf1b2326b734896734c6e167e41766f9cee7686a ]

nbd requires socket families to support the shutdown method so the nbd
recv workqueue can be woken up from its sock_recvmsg call. If the socket
does not support the callout we will leave recv works running or get hangs
later when the device or module is removed.

This adds a check during socket connection/reconnection to make sure the
socket being passed in supports the needed callout.

Reported-by: syzbot+24c12fa8d218ed26011a@syzkaller.appspotmail.com
Fixes: e9e006f5fcf2 ("nbd: fix max number of supported devs")
Tested-by: NRichard W.M. Jones <rjones@redhat.com>
Signed-off-by: NMike Christie <mchristi@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 12e36d98d3e5acf5fc57774e0a15906d55f30cb9 ]

We currently support two NICs in FW version 29, namely 7265D and 3168.
Out of these, only 7265D supports GEO SAR, so adjust the function that
checks for it accordingly.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Fixes: f5a47fae6aa3 ("iwlwifi: mvm: fix version check for GEO_TX_POWER_LIMIT support")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1099f48457d06b816359fb43ac32a4a07e33219b ]

Headphone on XPS 9350/9360 produces a background white noise. The The
noise level somehow correlates with "Headphone Mic Boost", when it sets
to 1 the noise disappears. However, doing this has a side effect, which
also decreases the overall headphone volume so I didn't send the patch
upstream.

The noise was bearable back then, but after commit 717f43d81afc ("ALSA:
hda/realtek - Update headset mode for ALC256") the noise exacerbates to
a point it starts hurting ears.

So let's use the workaround to set "Headphone Mic Boost" to 1 and lock
it so it's not touchable by userspace.

Fixes: 717f43d81afc ("ALSA: hda/realtek - Update headset mode for ALC256")
BugLink: https://bugs.launchpad.net/bugs/1654448
BugLink: https://bugs.launchpad.net/bugs/1845810Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20191003043919.10960-1-kai.heng.feng@canonical.comSigned-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4c0742f65b4ee466546fd24b71b56516cacd4613 ]

It was reported that 72cd4064fcca "NOMMU: Toggle only bits in
EXC_RETURN we are really care of" breaks NOMMU+XIP combination.
It happens because saved EXC_RETURN gets overwritten when data
section is relocated.

The fix is to propagate EXC_RETURN via register and let relocation
code to commit that value into memory.

Fixes: 72cd4064fcca ("ARM: 8830/1: NOMMU: Toggle only bits in EXC_RETURN we are really care of")
Reported-by: Nafzal mohammed <afzal.mohd.ma@gmail.com>
Tested-by: Nafzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: NVladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d303de1fcf344ff7c15ed64c3f48a991c9958775 ]

A customer reported the following softlockup:

[899688.160002] NMI watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [test.sh:16464]
[899688.160002] CPU: 0 PID: 16464 Comm: test.sh Not tainted 4.12.14-6.23-azure #1 SLE12-SP4
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] Kernel panic - not syncing: softlockup: hung tasks
[899688.160002] RIP: 0010:up_write+0x1a/0x30
[899688.160002] RSP: 0018:ffffa86784d4fde8 EFLAGS: 00000257 ORIG_RAX: ffffffffffffff12
[899688.160002] RAX: ffffffff970fea00 RBX: 0000000000000001 RCX: 0000000000000000
[899688.160002] RDX: ffffffff00000001 RSI: 0000000000000080 RDI: ffffffff970fea00
[899688.160002] RBP: ffffffffffffffff R08: ffffffffffffffff R09: 0000000000000000
[899688.160002] R10: 0000000000000000 R11: 0000000000000000 R12: ffff8b59014720d8
[899688.160002] R13: ffff8b59014720c0 R14: ffff8b5901471090 R15: ffff8b5901470000
[899688.160002]  tracing_read_pipe+0x336/0x3c0
[899688.160002]  __vfs_read+0x26/0x140
[899688.160002]  vfs_read+0x87/0x130
[899688.160002]  SyS_read+0x42/0x90
[899688.160002]  do_syscall_64+0x74/0x160

It caught the process in the middle of trace_access_unlock(). There is
no loop. So, it must be looping in the caller tracing_read_pipe()
via the "waitagain" label.

Crashdump analyze uncovered that iter->seq was completely zeroed
at this point, including iter->seq.seq.size. It means that
print_trace_line() was never able to print anything and
there was no forward progress.

The culprit seems to be in the code:

	/* reset all but tr, trace, and overruns */
	memset(&iter->seq, 0,
	       sizeof(struct trace_iterator) -
	       offsetof(struct trace_iterator, seq));

It was added by the commit 53d0aa77 ("ftrace:
add logic to record overruns"). It was v2.6.27-rc1.
It was the time when iter->seq looked like:

     struct trace_seq {
	unsigned char		buffer[PAGE_SIZE];
	unsigned int		len;
     };

There was no "size" variable and zeroing was perfectly fine.

The solution is to reinitialize the structure after or without
zeroing.

Link: http://lkml.kernel.org/r/20191011142134.11997-1-pmladek@suse.comSigned-off-by: NPetr Mladek <pmladek@suse.com>
Signed-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 062795fcdcb2d22822fb42644b1d76a8ad8439b3 ]

Depending on inlining decisions by the compiler, __get/put_user_fn
might become out of line. Then the compiler is no longer able to tell
that size can only be 1,2,4 or 8 due to the check in __get/put_user
resulting in false positives like

./arch/s390/include/asm/uaccess.h: In function ‘__put_user_fn’:
./arch/s390/include/asm/uaccess.h:113:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  113 |  return rc;
      |         ^~
./arch/s390/include/asm/uaccess.h: In function ‘__get_user_fn’:
./arch/s390/include/asm/uaccess.h:143:9: warning: ‘rc’ may be used uninitialized in this function [-Wmaybe-uninitialized]
  143 |  return rc;
      |         ^~

These functions are supposed to be always inlined. Mark it as such.
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: NVasily Gorbik <gor@linux.ibm.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1047ec868332034d1fbcb2fae19fe6d4cb869ff2 ]

Our client can issue multiple SETCLIENTID operations to the same
server in some circumstances. Ensure that calls to
nfs4_proc_setclientid() after the first one do not overwrite the
previously allocated cl_acceptor string.

unreferenced object 0xffff888461031800 (size 32):
  comm "mount.nfs", pid 2227, jiffies 4294822467 (age 1407.749s)
  hex dump (first 32 bytes):
    6e 66 73 40 6b 6c 69 6d 74 2e 69 62 2e 31 30 31  nfs@klimt.ib.101
    35 67 72 61 6e 67 65 72 2e 6e 65 74 00 00 00 00  5granger.net....
  backtrace:
    [<00000000ab820188>] __kmalloc+0x128/0x176
    [<00000000eeaf4ec8>] gss_stringify_acceptor+0xbd/0x1a7 [auth_rpcgss]
    [<00000000e85e3382>] nfs4_proc_setclientid+0x34e/0x46c [nfsv4]
    [<000000003d9cf1fa>] nfs40_discover_server_trunking+0x7a/0xed [nfsv4]
    [<00000000b81c3787>] nfs4_discover_server_trunking+0x81/0x244 [nfsv4]
    [<000000000801b55f>] nfs4_init_client+0x1b0/0x238 [nfsv4]
    [<00000000977daf7f>] nfs4_set_client+0xfe/0x14d [nfsv4]
    [<0000000053a68a2a>] nfs4_create_server+0x107/0x1db [nfsv4]
    [<0000000088262019>] nfs4_remote_mount+0x2c/0x59 [nfsv4]
    [<00000000e84a2fd0>] legacy_get_tree+0x2d/0x4c
    [<00000000797e947c>] vfs_get_tree+0x20/0xc7
    [<00000000ecabaaa8>] fc_mount+0xe/0x36
    [<00000000f15fafc2>] vfs_kern_mount+0x74/0x8d
    [<00000000a3ff4e26>] nfs_do_root_mount+0x8a/0xa3 [nfsv4]
    [<00000000d1c2b337>] nfs4_try_mount+0x58/0xad [nfsv4]
    [<000000004c9bddee>] nfs_fs_mount+0x820/0x869 [nfs]

Fixes: f11b2a1c ("nfs4: copy acceptor name from context ... ")
Signed-off-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NAnna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 862488105b84ca744b3d8ff131e0fcfe10644be1 ]

1. nbd_put takes the mutex and drops nbd->ref to 0. It then does
idr_remove and drops the mutex.

2. nbd_genl_connect takes the mutex. idr_find/idr_for_each fails
to find an existing device, so it does nbd_dev_add.

3. just before the nbd_put could call nbd_dev_remove or not finished
totally, but if nbd_dev_add try to add_disk, we can hit:

debugfs: Directory 'nbd1' with parent 'block' already present!

This patch will make sure all the disk add/remove stuff are done
by holding the nbd_index_mutex lock.
Reported-by: NMike Christie <mchristi@redhat.com>
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NXiubo Li <xiubli@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e0b0cb9388642c104838fac100a4af32745621e2 ]

In hgcm_call_preprocess_linaddr memory is allocated for bounce_buf but
is not released if copy_form_user fails. In order to prevent memory leak
in case of failure, the assignment to bounce_buf_ret is moved before the
error check. This way the allocated bounce_buf will be released by the
caller.

Fixes: 579db9d4 ("virt: Add vboxguest VMMDEV communication code")
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20190930204223.3660-1-navid.emamdoost@gmail.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit efcb529694c3b707dc0471b312944337ba16e4dd ]

Use ARRAY_SIZE to caluculate the top of the o32 stack.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 46f1619500d022501a4f0389f9f4c349ab46bb86 ]

Commit ac7c3e4ff401 ("compiler: enable CONFIG_OPTIMIZE_INLINING
forcibly") allows compiler to uninline functions marked as 'inline'.
In cace of __xchg this would cause to reference function
__xchg_called_with_bad_pointer, which is an error case
for catching bugs and will not happen for correct code, if
__xchg is inlined.
Signed-off-by: NThomas Bogendoerfer <tbogendoerfer@suse.de>
Reviewed-by: NPhilippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: NPaul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ab612b1daf415b62c58e130cb3d0f30b255a14d0 ]

In adis_update_scan_mode, if allocation for adis->buffer fails,
previously allocated adis->xfer needs to be released.
Signed-off-by: NNavid Emamdoost <navid.emamdoost@gmail.com>
Reviewed-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NJonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 083164dbdb17c5ea4ad92c1782b59c9d75567790 ]

cleanup error handling code and make sure temporary info array
with the handles are freed by amdgpu_bo_list_put() on
idr_replace()'s failure.
Signed-off-by: NNirmoy Das <nirmoy.das@amd.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit df4d29732fdad43a51284f826bec3e6ded177540 ]

It turns out that the NMI latency workaround from commit:

  6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")

ends up being too conservative and results in the perf NMI handler claiming
NMIs too easily on AMD hardware when the NMI watchdog is active.

This has an impact, for example, on the hpwdt (HPE watchdog timer) module.
This module can produce an NMI that is used to reset the system. It
registers an NMI handler for the NMI_UNKNOWN type and relies on the fact
that nothing has claimed an NMI so that its handler will be invoked when
the watchdog device produces an NMI. After the referenced commit, the
hpwdt module is unable to process its generated NMI if the NMI watchdog is
active, because the current NMI latency mitigation results in the NMI
being claimed by the perf NMI handler.

Update the AMD perf NMI latency mitigation workaround to, instead, use a
window of time. Whenever a PMC is handled in the perf NMI handler, set a
timestamp which will act as a perf NMI window. Any NMIs arriving within
that window will be claimed by perf. Anything outside that window will
not be claimed by perf. The value for the NMI window is set to 100 msecs.
This is a conservative value that easily covers any NMI latency in the
hardware. While this still results in a window in which the hpwdt module
will not receive its NMI, the window is now much, much smaller.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Jerry Hoemann <jerry.hoemann@hpe.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 6d3edaae16c6 ("x86/perf/amd: Resolve NMI latency issues for active PMCs")
Link: https://lkml.kernel.org/r/Message-ID:
Signed-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 68e7a4d66b0ce04bf18ff2ffded5596ab3618585 ]

vtime_account_system() assumes that the target task to account cputime
to is always the current task. This is most often true indeed except on
task switch where we call:

	vtime_common_task_switch(prev)
		vtime_account_system(prev)

Here prev is the scheduling-out task where we account the cputime to. It
doesn't match current that is already the scheduling-in task at this
stage of the context switch.

So we end up checking the wrong task flags to determine if we are
accounting guest or system time to the previous task.

As a result the wrong task is used to check if the target is running in
guest mode. We may then spuriously account or leak either system or
guest time on task switch.

Fix this assumption and also turn vtime_guest_enter/exit() to use the
task passed in parameter as well to avoid future similar issues.
Signed-off-by: NFrederic Weisbecker <frederic@kernel.org>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wanpeng Li <wanpengli@tencent.com>
Fixes: 2a42eb95 ("sched/cputime: Accumulate vtime on top of nsec clocksource")
Link: https://lkml.kernel.org/r/20190925214242.21873-1-frederic@kernel.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8d7c6ac3b2371eb1cbc9925a88f4d10efff374de ]

Comet Lake is the new 10th Gen Intel processor. Add two new CPU model
numbers to the Intel family list.

The CPU model numbers are not published in the SDM yet but they come
from an authoritative internal source.

 [ bp: Touch up commit message. ]
Signed-off-by: NKan Liang <kan.liang@linux.intel.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NTony Luck <tony.luck@intel.com>
Cc: ak@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/1570549810-25049-2-git-send-email-kan.liang@linux.intel.comSigned-off-by: NSasha Levin <sashal@kernel.org>