When phy_init_hw() fails at phy_attach_direct();
- phy_detach() calls phy_led_triggers_unregister() without
  previous call of phy_led_triggers_register().
- still call phy_led_triggers_register() and cause memory leak.

Fixes: 2e0bc452 ("net: phy: leds: add support for led triggers on phy link state change")
Signed-off-by: NWoojung Huh <woojung.huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Typical NAPI drivers use napi_consume_skb(skb) at TX completion time.
This put skb in a percpu special queue, napi_alloc_cache, to get bulk
frees.

It turns out the queue is not flushed and hits the NAPI_SKB_CACHE_SIZE
limit quite often, with skbs that were queued hundreds of usec earlier.
I measured this can take ~6000 nsec to perform one flush.

__kfree_skb_flush() can be called from two points right now :

1) From net_tx_action(), but only for skbs that were queued to
sd->completion_queue.

 -> Irrelevant for NAPI drivers in normal operation.

2) From net_rx_action(), but only under high stress or if RPS/RFS has a
pending action.

This patch changes net_rx_action() to perform the flush in all cases and
after more urgent operations happened (like kicking remote CPUS for
RPS/RFS).
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Mack says:

====================
Add eBPF hooks for cgroups

This is v9 of the patch set to allow eBPF programs for network
filtering and accounting to be attached to cgroups, so that they apply
to all sockets of all tasks placed in that cgroup. The logic also
allows to be extendeded for other cgroup based eBPF logic.

Again, only minor details are updated in this version.

Changes from v8:

* Move the egress hooks into ip_finish_output() and ip6_finish_output()
  so they run after the netfilter hooks. For IPv4 multicast, add a new
  ip_mc_finish_output() callback that is invoked on success by
  netfilter, and call the eBPF program from there.

Changes from v7:

* Replace the static inline function cgroup_bpf_run_filter() with
  two specific macros for ingress and egress.  This addresses David
  Miller's concern regarding skb->sk vs. sk in the egress path.
  Thanks a lot to Daniel Borkmann and Alexei Starovoitov for the
  suggestions.

Changes from v6:

* Rebased to 4.9-rc2

* Add EXPORT_SYMBOL(__cgroup_bpf_run_filter). The kbuild test robot
  now succeeds in building this version of the patch set.

* Switch from bpf_prog_run_save_cb() to bpf_prog_run_clear_cb() to not
  tamper with the contents of skb->cb[]. Pointed out by Daniel
  Borkmann.

* Use sk_to_full_sk() in the egress path, as suggested by Daniel
  Borkmann.

* Renamed BPF_PROG_TYPE_CGROUP_SOCKET to BPF_PROG_TYPE_CGROUP_SKB, as
  requested by David Ahern.

* Added Alexei's Acked-by tags.

Changes from v5:

* The eBPF programs now operate on L3 rather than on L2 of the packets,
  and the egress hooks were moved from __dev_queue_xmit() to
  ip*_output().

* For BPF_PROG_TYPE_CGROUP_SOCKET, disallow direct access to the skb
  through BPF_LD_[ABS|IND] instructions, but hook up the
  bpf_skb_load_bytes() access helper instead. Thanks to Daniel Borkmann
  for the help.

Changes from v4:

* Plug an skb leak when dropping packets due to eBPF verdicts in
  __dev_queue_xmit(). Spotted by Daniel Borkmann.

* Check for sk_fullsock(sk) in __cgroup_bpf_run_filter() so we don't
  operate on timewait or request sockets. Suggested by Daniel Borkmann.

* Add missing @parent parameter in kerneldoc of __cgroup_bpf_update().
  Spotted by Rami Rosen.

* Include linux/jump_label.h from bpf-cgroup.h to fix a kbuild error.

Changes from v3:

* Dropped the _FILTER suffix from BPF_PROG_TYPE_CGROUP_SOCKET_FILTER,
  renamed BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS to
  BPF_CGROUP_INET_{IN,E}GRESS and alias BPF_MAX_ATTACH_TYPE to
  __BPF_MAX_ATTACH_TYPE, as suggested by Daniel Borkmann.

* Dropped the attach_flags member from the anonymous struct for BPF
  attach operations in union bpf_attr. They can be added later on via
  CHECK_ATTR. Requested by Daniel Borkmann and Alexei.

* Release old_prog at the end of __cgroup_bpf_update rather that at
  the beginning to fix a race gap between program updates and their
  users. Spotted by Daniel Borkmann.

* Plugged an skb leak when dropping packets on the egress path.
  Spotted by Daniel Borkmann.

* Add cgroups@vger.kernel.org to the loop, as suggested by Rami Rosen.

* Some minor coding style adoptions not worth mentioning in particular.

Changes from v2:

* Fixed the RCU locking details Tejun pointed out.

* Assert bpf_attr.flags == 0 in BPF_PROG_DETACH syscall handler.

Changes from v1:

* Moved all bpf specific cgroup code into its own file, and stub
  out related functions for !CONFIG_CGROUP_BPF as static inline nops.
  This way, the call sites are not cluttered with #ifdef guards while
  the feature remains compile-time configurable.

* Implemented the new scheme proposed by Tejun. Per cgroup, store one
  set of pointers that are pinned to the cgroup, and one for the
  programs that are effective. When a program is attached or detached,
  the change is propagated to all the cgroup's descendants. If a
  subcgroup has its own pinned program, skip the whole subbranch in
  order to allow delegation models.

* The hookup for egress packets is now done from __dev_queue_xmit().

* A static key is now used in both the ingress and egress fast paths
  to keep performance penalties close to zero if the feature is
  not in use.

* Overall cleanup to make the accessors use the program arrays.
  This should make it much easier to add new program types, which
  will then automatically follow the pinned vs. effective logic.

* Fixed locking issues, as pointed out by Eric Dumazet and Alexei
  Starovoitov. Changes to the program array are now done with
  xchg() and are protected by cgroup_mutex.

* eBPF programs are now expected to return 1 to let the packet pass,
  not >= 0. Pointed out by Alexei.

* Operation is now limited to INET sockets, so local AF_UNIX sockets
  are not affected. The enum members are renamed accordingly. In case
  other socket families should be supported, this can be extended in
  the future.

* The sample program learned to support both ingress and egress, and
  can now optionally make the eBPF program drop packets by making it
  return 0.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a simple userpace program to demonstrate the new API to attach eBPF
programs to cgroups. This is what it does:

 * Create arraymap in kernel with 4 byte keys and 8 byte values

 * Load eBPF program

   The eBPF program accesses the map passed in to store two pieces of
   information. The number of invocations of the program, which maps
   to the number of packets received, is stored to key 0. Key 1 is
   incremented on each iteration by the number of bytes stored in
   the skb.

 * Detach any eBPF program previously attached to the cgroup

 * Attach the new program to the cgroup using BPF_PROG_ATTACH

 * Once a second, read map[0] and map[1] to see how many bytes and
   packets were seen on any socket of tasks in the given cgroup.

The program takes a cgroup path as 1st argument, and either "ingress"
or "egress" as 2nd. Optionally, "drop" can be passed as 3rd argument,
which will make the generated eBPF program return 0 instead of 1, so
the kernel will drop the packet.

libbpf gained two new wrappers for the new syscall commands.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from ip_output(), ip6_output() and
ip_mc_output(). From mentioned functions we have two socket contexts
as per 7026b1dd ("netfilter: Pass socket pointer down through
okfn()."). We explicitly need to use sk instead of skb->sk here,
since otherwise the same program would run multiple times on egress
when encap devices are involved, which is not desired in our case.

eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).

Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the cgroup associated with the receiving socket has an eBPF
programs installed, run them from sk_filter_trim_cap().

eBPF programs used in this context are expected to either return 1 to
let the packet pass, or != 1 to drop them. The programs have access to
the skb through bpf_skb_load_bytes(), and the payload starts at the
network headers (L3).

Note that cgroup_bpf_run_filter() is stubbed out as static inline nop
for !CONFIG_CGROUP_BPF, and is otherwise guarded by a static key if
the feature is unused.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the bpf(2) syscall by two new commands, BPF_PROG_ATTACH and
BPF_PROG_DETACH which allow attaching and detaching eBPF programs
to a target.

On the API level, the target could be anything that has an fd in
userspace, hence the name of the field in union bpf_attr is called
'target_fd'.

When called with BPF_ATTACH_TYPE_CGROUP_INET_{E,IN}GRESS, the target is
expected to be a valid file descriptor of a cgroup v2 directory which
has the bpf controller enabled. These are the only use-cases
implemented by this patch at this point, but more can be added.

If a program of the given type already exists in the given cgroup,
the program is swapped automically, so userspace does not have to drop
an existing program first before installing a new one, which would
otherwise leave a gap in which no program is attached.

For more information on the propagation logic to subcgroups, please
refer to the bpf cgroup controller implementation.

The API is guarded by CAP_NET_ADMIN.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds two sets of eBPF program pointers to struct cgroup.
One for such that are directly pinned to a cgroup, and one for such
that are effective for it.

To illustrate the logic behind that, assume the following example
cgroup hierarchy.

  A - B - C
        \ D - E

If only B has a program attached, it will be effective for B, C, D
and E. If D then attaches a program itself, that will be effective for
both D and E, and the program in B will only affect B and C. Only one
program of a given type is effective for a cgroup.

Attaching and detaching programs will be done through the bpf(2)
syscall. For now, ingress and egress inet socket filtering are the
only supported use-cases.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This program type is similar to BPF_PROG_TYPE_SOCKET_FILTER, except that
it does not allow BPF_LD_[ABS|IND] instructions and hooks up the
bpf_skb_load_bytes() helper.

Programs of this type will be attached to cgroups for network filtering
and accounting.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently if txq_info->uldtxq cannot be allocated then
txq_info->txq is being kfree'd (which is redundant because it
is NULL) instead of txq_info. Fix this by instead kfree'ing
txq_info.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After commit 1576d986 ("tun: switch to use skb array for tx"),
sk_receive_queue was not used any more. So remove the uncessary
sk_receive_queue length check during xmit.
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

llvm can emit relocations into sections other than program code
(like debug info sections). Ignore them during parsing of elf file
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

since llvm commit "Do not expand UNDEF SDNode during insn selection lowering"
llvm will generate code that uses uninitialized registers for cases
where C code is actually uses uninitialized data.
So this sockex2 example is technically broken.
Fix it by initializing on the stack variable fully.
Also increase verifier buffer limit, since verifier output
may not fit in 64k for this sockex2 code depending on llvm version.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Goal is to reorganize this critical structure to increase performance.

ndo_start_xmit() should only dirty one cache line, and access as few
cache lines as possible.

Add sp_ (Slow Path) prefix to fields that are not used in fast path,
to make clear what is going on.

After this patch pahole reports something much better, as all
ndo_start_xmit() needed fields are packed into two cache lines instead
of seven or eight

struct mlx4_en_tx_ring {
	u32                        last_nr_txbb;         /*     0   0x4 */
	u32                        cons;                 /*   0x4   0x4 */
	long unsigned int          wake_queue;           /*   0x8   0x8 */
	struct netdev_queue *      tx_queue;             /*  0x10   0x8 */
	u32                        (*free_tx_desc)(struct mlx4_en_priv *, struct mlx4_en_tx_ring *, int, u8, u64, int); /*  0x18   0x8 */
	struct mlx4_en_rx_ring *   recycle_ring;         /*  0x20   0x8 */

	/* XXX 24 bytes hole, try to pack */

	/* --- cacheline 1 boundary (64 bytes) --- */
	u32                        prod;                 /*  0x40   0x4 */
	unsigned int               tx_dropped;           /*  0x44   0x4 */
	long unsigned int          bytes;                /*  0x48   0x8 */
	long unsigned int          packets;              /*  0x50   0x8 */
	long unsigned int          tx_csum;              /*  0x58   0x8 */
	long unsigned int          tso_packets;          /*  0x60   0x8 */
	long unsigned int          xmit_more;            /*  0x68   0x8 */
	struct mlx4_bf             bf;                   /*  0x70  0x18 */
	/* --- cacheline 2 boundary (128 bytes) was 8 bytes ago --- */
	__be32                     doorbell_qpn;         /*  0x88   0x4 */
	__be32                     mr_key;               /*  0x8c   0x4 */
	u32                        size;                 /*  0x90   0x4 */
	u32                        size_mask;            /*  0x94   0x4 */
	u32                        full_size;            /*  0x98   0x4 */
	u32                        buf_size;             /*  0x9c   0x4 */
	void *                     buf;                  /*  0xa0   0x8 */
	struct mlx4_en_tx_info *   tx_info;              /*  0xa8   0x8 */
	int                        qpn;                  /*  0xb0   0x4 */
	u8                         queue_index;          /*  0xb4   0x1 */
	bool                       bf_enabled;           /*  0xb5   0x1 */
	bool                       bf_alloced;           /*  0xb6   0x1 */
	u8                         hwtstamp_tx_type;     /*  0xb7   0x1 */
	u8 *                       bounce_buf;           /*  0xb8   0x8 */
	/* --- cacheline 3 boundary (192 bytes) --- */
	long unsigned int          queue_stopped;        /*  0xc0   0x8 */
	struct mlx4_hwq_resources  sp_wqres;             /*  0xc8  0x58 */
	/* --- cacheline 4 boundary (256 bytes) was 32 bytes ago --- */
	struct mlx4_qp             sp_qp;                /* 0x120  0x30 */
	/* --- cacheline 5 boundary (320 bytes) was 16 bytes ago --- */
	struct mlx4_qp_context     sp_context;           /* 0x150  0xf8 */
	/* --- cacheline 9 boundary (576 bytes) was 8 bytes ago --- */
	cpumask_t                  sp_affinity_mask;     /* 0x248  0x20 */
	enum mlx4_qp_state         sp_qp_state;          /* 0x268   0x4 */
	u16                        sp_stride;            /* 0x26c   0x2 */
	u16                        sp_cqn;               /* 0x26e   0x2 */

	/* size: 640, cachelines: 10, members: 36 */
	/* sum members: 600, holes: 1, sum holes: 24 */
	/* padding: 16 */
};

Instead of this silly placement :

struct mlx4_en_tx_ring {
	u32                        last_nr_txbb;         /*     0   0x4 */
	u32                        cons;                 /*   0x4   0x4 */
	long unsigned int          wake_queue;           /*   0x8   0x8 */

	/* XXX 48 bytes hole, try to pack */

	/* --- cacheline 1 boundary (64 bytes) --- */
	u32                        prod;                 /*  0x40   0x4 */

	/* XXX 4 bytes hole, try to pack */

	long unsigned int          bytes;                /*  0x48   0x8 */
	long unsigned int          packets;              /*  0x50   0x8 */
	long unsigned int          tx_csum;              /*  0x58   0x8 */
	long unsigned int          tso_packets;          /*  0x60   0x8 */
	long unsigned int          xmit_more;            /*  0x68   0x8 */
	unsigned int               tx_dropped;           /*  0x70   0x4 */

	/* XXX 4 bytes hole, try to pack */

	struct mlx4_bf             bf;                   /*  0x78  0x18 */
	/* --- cacheline 2 boundary (128 bytes) was 16 bytes ago --- */
	long unsigned int          queue_stopped;        /*  0x90   0x8 */
	cpumask_t                  affinity_mask;        /*  0x98  0x10 */
	struct mlx4_qp             qp;                   /*  0xa8  0x30 */
	/* --- cacheline 3 boundary (192 bytes) was 24 bytes ago --- */
	struct mlx4_hwq_resources  wqres;                /*  0xd8  0x58 */
	/* --- cacheline 4 boundary (256 bytes) was 48 bytes ago --- */
	u32                        size;                 /* 0x130   0x4 */
	u32                        size_mask;            /* 0x134   0x4 */
	u16                        stride;               /* 0x138   0x2 */

	/* XXX 2 bytes hole, try to pack */

	u32                        full_size;            /* 0x13c   0x4 */
	/* --- cacheline 5 boundary (320 bytes) --- */
	u16                        cqn;                  /* 0x140   0x2 */

	/* XXX 2 bytes hole, try to pack */

	u32                        buf_size;             /* 0x144   0x4 */
	__be32                     doorbell_qpn;         /* 0x148   0x4 */
	__be32                     mr_key;               /* 0x14c   0x4 */
	void *                     buf;                  /* 0x150   0x8 */
	struct mlx4_en_tx_info *   tx_info;              /* 0x158   0x8 */
	struct mlx4_en_rx_ring *   recycle_ring;         /* 0x160   0x8 */
	u32                        (*free_tx_desc)(struct mlx4_en_priv *, struct mlx4_en_tx_ring *, int, u8, u64, int); /* 0x168   0x8 */
	u8 *                       bounce_buf;           /* 0x170   0x8 */
	struct mlx4_qp_context     context;              /* 0x178  0xf8 */
	/* --- cacheline 9 boundary (576 bytes) was 48 bytes ago --- */
	int                        qpn;                  /* 0x270   0x4 */
	enum mlx4_qp_state         qp_state;             /* 0x274   0x4 */
	u8                         queue_index;          /* 0x278   0x1 */
	bool                       bf_enabled;           /* 0x279   0x1 */
	bool                       bf_alloced;           /* 0x27a   0x1 */

	/* XXX 5 bytes hole, try to pack */

	/* --- cacheline 10 boundary (640 bytes) --- */
	struct netdev_queue *      tx_queue;             /* 0x280   0x8 */
	int                        hwtstamp_tx_type;     /* 0x288   0x4 */

	/* size: 704, cachelines: 11, members: 36 */
	/* sum members: 587, holes: 6, sum holes: 65 */
	/* padding: 52 */
};
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

PHY drivers should be able to rely on the caller of {get,set}_tunable to
have acquired the PHY device mutex, in order to both serialize against
concurrent calls of these functions, but also against PHY state machine
changes. All ethtool PHY-level functions do this, except
{get,set}_tunable, so we make them consistent here as well.

We need to update the Microsemi PHY driver in the same commit to avoid
introducing either deadlocks, or lack of proper locking.

Fixes: 968ad9da ("ethtool: Implements ETHTOOL_PHY_GTUNABLE/ETHTOOL_PHY_STUNABLE")
Fixes: 310d9ad5 ("net: phy: Add downshift get/set support in Microsemi PHYs driver")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NAllan W. Nielsen <allan.nielsen@microsemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox 100G mlx5 SRIOV switchdev update

This series from Roi and Or further enhances the new SRIOV switchdev mode.

Roi's patches deal with allowing users to configure though devlink
the level of inline headers that the VF should be setting in order for
the eswitch HW to do proper matching. We also enforce that the matching
required for offloaded TC rules is aligned with that level on the PF driver.

Or's patches deals with allowing the user to control on the VF operational
link state through admin directives on the mlx5 VF rep link. Also in this series
is implementation of HW and SW counters for the mlx5 VF rep which is aligned
with the design set by commit a5ea31f5 'Merge branch net-offloaded-stats'.

v1 --> v2:
* constified the net-device param of get offloaded stats ndo in mlxsw
  (pointed by 0-day screaming on us...)
* added Or's Review-by tags for Roi's patches

This series was generated against commit
e796f49d ("net: ieee802154: constify ieee802154_ops structures")
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A flow should be offloaded only if the matches are
allowed according to min inline mode.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement devlink show and set of HW inline-mode.
The supported modes: none, link, network, transport.
We currently support one mode for all vports so set is done on all vports.
When eswitch is first initialized the inline-mode is queried from the FW.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also move the inline capablities enum to a shared header vport.h
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some HWs need the VF driver to put part of the packet headers on the
TX descriptor so the e-switch can do proper matching and steering.

The supported modes: none, link, network, transport.
Signed-off-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reflect the administative link changes done on the VF representor to the
VF e-switch vport. This means that doing ip link set down/up commands on
the VF rep will modify the e-switch vport state which in turn will make
proper VF drivers to set their carrier accordingly.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switchdev driver net-device port statistics should follow the model introduced
in commit a5ea31f5 'Merge branch net-offloaded-stats'.

For VF reps we return the SRIOV eswitch vport stats as the usual ones and SW stats
if asked. For the PF, if we're in the switchdev mode, we return the uplink stats
and SW stats if asked, otherwise as before. The uplink stats are implemented using
the PPCNT 802_3 counters which are already being read/cached by the driver.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers would need to check few internal matters for
that. To be used in downstream mlx5 commit.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: broadcom: Wirespeed/downshift support

This patch series adds support for the Broadcom Wirespeed, aka
downsfhit feature utilizing the recently added ethtool PHY tunables.

Tested with two Gigabit link partners with a 4-wire cable having only
2 pairs connected.

Last patch in the series is a fix that was required for testing, which
should make it to -stable, which I can submit separate against net if
you prefer David.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case the link change and EEE is enabled or disabled, always try to
re-negotiate this with the link partner.

Fixes: 450b05c1 ("net: dsa: bcm_sf2: add support for controlling EEE")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Broadcom's Wirespeed feature allows us to configure how auto-negotiation
should behave with fewer working pairs of wires on a cable. Add support
code for retrieving and setting such downshift counters using the
recently added ethtool downshift tunables.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to need these functions to implement support for Broadcom
Wirespeed, aka downshift.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit 2331ccc5 ("tcp: enhance tcp collapsing"),
we made a first step allowing copying right skb to left skb head.

Since all skbs in socket write queue are headless (but possibly the very
first one), this strategy often does not work.

This patch extends tcp_collapse_retrans() to perform frag shifting,
thanks to skb_shift() helper.

This helper needs to not BUG on non headless skbs, as callers are ok
with that.

Tested:

Following packetdrill test now passes :

0.000 socket(..., SOCK_STREAM, IPPROTO_TCP) = 3
   +0 setsockopt(3, SOL_SOCKET, SO_REUSEADDR, [1], 4) = 0
   +0 bind(3, ..., ...) = 0
   +0 listen(3, 1) = 0

   +0 < S 0:0(0) win 32792 <mss 1460,sackOK,nop,nop,nop,wscale 8>
   +0 > S. 0:0(0) ack 1 <mss 1460,nop,nop,sackOK,nop,wscale 8>
+.100 < . 1:1(0) ack 1 win 257
   +0 accept(3, ..., ...) = 4

   +0 setsockopt(4, SOL_TCP, TCP_NODELAY, [1], 4) = 0
   +0 write(4, ..., 200) = 200
   +0 > P. 1:201(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 201:401(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 401:601(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 601:801(200) ack 1
+.001 write(4, ..., 200) = 200
   +0 > P. 801:1001(200) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1001:1101(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1101:1201(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1201:1301(100) ack 1
+.001 write(4, ..., 100) = 100
   +0 > P. 1301:1401(100) ack 1

+.099 < . 1:1(0) ack 201 win 257
+.001 < . 1:1(0) ack 201 win 257 <nop,nop,sack 1001:1401>
   +0 > P. 201:1001(800) ack 1
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the MV88E6097 switch. The change was tested on an Armada
based platform with a MV88E6097 switch.
Signed-off-by: NStefan Eichenberger <stefan.eichenberger@netmodule.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it possible to generate trace events for mdio read and write accesses.
Signed-off-by: NUwe Kleine-König <uwe@kleine-koenig.org>
Acked-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VMware VMCI transport supports loopback inside virtual machines.
This patch implements loopback for virtio-vsock.

Flow control is handled by the virtio-vsock protocol as usual.  The
sending process stops transmitting on a connection when the peer's
receive buffer space is exhausted.

Cathy Avery <cavery@redhat.com> noticed this difference between VMCI and
virtio-vsock when a test case using loopback failed.  Although loopback
isn't the main point of AF_VSOCK, it is useful for testing and
virtio-vsock must match VMCI semantics so that userspace programs run
regardless of the underlying transport.

My understanding is that loopback is not supported on the host side with
VMCI.  Follow that by implementing it only in the guest driver, not the
vhost host driver.

Cc: Jorgen Hansen <jhansen@vmware.com>
Reported-by: NCathy Avery <cavery@redhat.com>
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All conflicts were simple overlapping changes except perhaps
for the Thunder driver.

That driver has a change_mtu method explicitly for sending
a message to the hardware.  If that fails it returns an
error.

Normally a driver doesn't need an ndo_change_mtu method becuase those
are usually just range changes, which are now handled generically.
But since this extra operation is needed in the Thunder driver, it has
to stay.

However, if the message send fails we have to restore the original
MTU before the change because the entire call chain expects that if
an error is thrown by ndo_change_mtu then the MTU did not change.
Therefore code is added to nicvf_change_mtu to remember the original
MTU, and to restore it upon nicvf_update_hw_max_frs() failue.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both of these drivers won't work on 64-bit architectures unless they
are redesigned, since they store a virtual address pointer in a 32-bit
field of the descriptors:

drivers/net/ethernet/marvell/mvneta_bm.c: In function 'mvneta_bm_construct':
drivers/net/ethernet/marvell/mvneta_bm.c:103:16: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_prs_vlan_init':
drivers/net/ethernet/marvell/mvpp2.c:2563:32: error: large integer implicitly truncated to unsigned type [-Werror=overflow]

This limits the COMPILE_TEST option for the two drivers again to
only build them on 32-bit. This seems nicer than shutting up the
warnings, in case we ever actually want to use them on 64-bit,
as the warnings indicate which parts of the driver are currently
broken there.

Fixes: a0627f77 ("net: marvell: Allow drivers to be built with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jiri Pirko says:

====================
mlxsw: core: Implement thermal zone

Implement thermal zone for mlxsw based HW.
The first patch is just a register dependency for the second patch.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement thermal zone for mlxsw based HW. It uses temperature sensor
provided by ASIC (the same as mlxsw hwmon interface) to report current
temp to thermal core. The ASIC's PWM is then used to control speed
of system fans registered as cooling devices.
Signed-off-by: NIvan Vecera <cera@cera.cz>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MFSL register is used to configure the fan speed event / interrupt
notification mechanism. Fan speed threshold are defined for both
under-speed and over-speed.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
Start adding support for mv88e6390

This is the first patchset implementing support for the mv88e6390
family.  This is a new generation of switch devices and has numerous
incompatible changes to the registers. These patches allow the switch
to the detected during probe, and makes the statistics unit work.

These patches are insufficient to make the mv88e6390 functional. More
patches will follow.

v2:
  Move stats code into global1
  Change DT compatible string to mv88e6190
  Fixed mv88e6351 stats which v1 had broken
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the stats functions which access global 1 registers into
global1.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>