It fixes L2CAP socket based security level elevation during a
connection. The HID profile needs this (for keyboards) and it is the only
way to achieve the security level elevation when using the management
interface to talk to the kernel (hence the management enabling patch
being the one that exposes this issue).

It enables the userspace a security level change when the socket is
already connected and create a way to notify the socket the result of the
request. At the moment of the request the socket is made non writable, if
the request fails the connections closes, otherwise the socket is made
writable again, POLL_OUT is emmited.
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In commit b0302aba, the rtlwifi family of drivers was converted to use
asynchronous firmware loading. Unfortumately, the implementation was
racy, and the ieee80211 routines could be started before rtl_init_core()
was called to setup the data.

This patch fixes the bug noted in https://bugzilla.kernel.org/show_bug.cgi?id=43187.
Reported-by: NJoshua Roys <Joshua.Roys@gtri.gatech.edu>
Tested-by: NNeptune Ning <frostyplanet@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>    [3.3]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

By default, iwlwifi uses order-1 pages (8 KB) to store incoming frames,
but doesnt say so in skb->truesize.

This makes very possible to exhaust kernel memory since these skb evade
normal socket memory accounting.

As struct ieee80211_hdr is going to be pulled before calling IP stack,
there is no need to use dev_alloc_skb() to reserve NET_SKB_PAD bytes.
alloc_skb() is ok in this driver, allowing more tailroom.

Pull beginning of frame in skb header, in the hope we can reuse order-1
pages in the driver immediately for small frames and reduce their
truesize to the minimum (linear skbs)
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Neal Cardwell <ncardwell@google.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit a844adfd.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.

spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.

So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.

Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: NKai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc_tl_lock is not acquired in the error handle code for bus down.
But it's unlocked using spin_unlock_irqrestore after finishing task
list walk down. Grab the lock before breaking the loop to avoid a
double unlock.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

EAP frames for stations in an AP VLAN are sent on the main AP interface
to avoid race conditions wrt. moving stations.
For that to work properly, sta_info_get_bss must be used instead of
sta_info_get when sending EAP packets.
Previously this was only done for cooked monitor injected packets, so
this patch adds a check for tx->skb->protocol to the same place.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This driver currently leaves elp_work behind when stopping, which
occasionally results in data corruption because work function ends
up accessing freed memory, typical symptoms of this are various
worker_thread crashes. Fix it by cancelling elp_work.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently SDIO glue frees it's own structure before calling
wl1251_free_hw(), which in turn calls ieee80211_unregister_hw().
The later call may result in a need to communicate with the chip
to stop it (as it happens now if the interface is still up before
rmmod), which means calls are made back to the glue, resulting in
freed memory access.

Fix this by freeing glue data last.

Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 2a190322 (b43: reload phy and bss settings after core restarts)
introduced an unconditional call to b43_op_config() at the end of
b43_op_start(). When firmware fails to load this can wedge the system.
There's no need to reload the configuration after a failed
initialization anyway, so only make the call if initialization was
successful.

BugLink: http://bugs.launchpad.net/bugs/950295
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

"iwlwifi: use correct released ucode version" change
the ucode api ok from 6000G2 to 6000G2B, but it shall belong
to 6030 device series, not the 6005 device series. Fix it

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When our driver device is removed on the AHB bus, our IO memory is never unmapped.
Signed-off-by: NJonathan Bither <jonbither@gmail.com>
Reviewed-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dpc takes care of all data packets transmissions for sdio function
2. It is possible that it misses some completion events when the
traffic is heavy or it's running on a slow cpu. A linked list is
introduced to make sure dpc is invoked whenever needed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

SDIO stack doesn't have a structure for function 0. The structure
pointer stored in card->sdio_func[0] is actually for function 1.
With current implementation the register read/write is applied to
function 1. This pathch fixes the issue.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NArend van Spriel <arend@broadcom.com>
Reviewed-by: NFlorian Fainelli <florian@openwrt.org>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ieee80211_mgd_teardown() is called on netdev removal, which
occurs after the vif was already removed from the low-level
driver, resulting in the following warning:

[ 4809.014734] ------------[ cut here ]------------
[ 4809.019861] WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211]()
[ 4809.030388] wlan0:  Failed check-sdata-in-driver check, flags: 0x4
[ 4809.036862] Modules linked in: wlcore_sdio(-) wl12xx wlcore mac80211 cfg80211 [last unloaded: cfg80211]
[ 4809.046849] [<c001bd4c>] (unwind_backtrace+0x0/0x12c)
[ 4809.055937] [<c047cf1c>] (dump_stack+0x20/0x24)
[ 4809.065385] [<c003e334>] (warn_slowpath_common+0x5c/0x74)
[ 4809.075589] [<c003e408>] (warn_slowpath_fmt+0x40/0x48)
[ 4809.088291] [<bf033630>] (ieee80211_bss_info_change_notify+0x200/0x2c8 [mac80211])
[ 4809.102844] [<bf067f84>] (ieee80211_destroy_auth_data+0x80/0xa4 [mac80211])
[ 4809.116276] [<bf068004>] (ieee80211_mgd_teardown+0x5c/0x74 [mac80211])
[ 4809.129331] [<bf043f18>] (ieee80211_teardown_sdata+0xb0/0xd8 [mac80211])
[ 4809.141595] [<c03b5e58>] (rollback_registered_many+0x228/0x2f0)
[ 4809.153056] [<c03b5f48>] (unregister_netdevice_many+0x28/0x50)
[ 4809.165696] [<bf041ea8>] (ieee80211_remove_interfaces+0xb4/0xdc [mac80211])
[ 4809.179151] [<bf032174>] (ieee80211_unregister_hw+0x50/0xf0 [mac80211])
[ 4809.191043] [<bf0bebb4>] (wlcore_remove+0x5c/0x7c [wlcore])
[ 4809.201491] [<c02c6918>] (platform_drv_remove+0x24/0x28)
[ 4809.212029] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.222738] [<c02c4e84>] (device_release_driver+0x30/0x3c)
[ 4809.233099] [<c02c4258>] (bus_remove_device+0x10c/0x128)
[ 4809.242620] [<c02c26f8>] (device_del+0x11c/0x17c)
[ 4809.252150] [<c02c6de0>] (platform_device_del+0x28/0x68)
[ 4809.263051] [<bf0df49c>] (wl1271_remove+0x3c/0x50 [wlcore_sdio])
[ 4809.273590] [<c03806b0>] (sdio_bus_remove+0x48/0xf8)
[ 4809.283754] [<c02c4d50>] (__device_release_driver+0x8c/0xcc)
[ 4809.293729] [<c02c4e2c>] (driver_detach+0x9c/0xc4)
[ 4809.303163] [<c02c3d7c>] (bus_remove_driver+0xc4/0xf4)
[ 4809.312973] [<c02c5a98>] (driver_unregister+0x70/0x7c)
[ 4809.323220] [<c03809c4>] (sdio_unregister_driver+0x24/0x2c)
[ 4809.334213] [<bf0df458>] (wl1271_exit+0x14/0x1c [wlcore_sdio])
[ 4809.344930] [<c009b1a4>] (sys_delete_module+0x228/0x2a8)
[ 4809.354734] ---[ end trace 515290ccf5feb522 ]---

Rename ieee80211_mgd_teardown() to ieee80211_mgd_stop(),
and call it on ieee80211_do_stop().
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Report correctly the latest released version
of the iwlwifi firmware for all
iwlwifi-supported devices.

Cc: stable@vger.kernel.org #3.3+
Signed-off-by: NMeenakshi Venkataraman <meenakshi.venkataraman@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Newer devices have 20 (5000 series) or 30 (6000 series)
hardware queues, rather than the 16 that 4965 had. This
was added to the driver a long time ago, but improperly:
the queue registers for the higher queues aren't just
continuations of the registers for the first 16 queues,
they are in other places. Therefore, the hardware would
lock up when trying to activate queue 16 or above and
the device would have to be restarted.

Thanks goes to Emmanuel who identified this and told me
how the queue programming should be done.

Note that we don't use queues 20 and higher today and
doing so needs more work than this.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change adds 0x0489:0xe033 to the btusb module.

This bluetooth usb device is integrated in the Acer TimelineX AS4830TG-6808 notebook.

Output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=02 Prnt=02 Port=05 Cnt=02 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e033 Rev= 2.29
S:  Manufacturer=Broadcom Corp
S:  Product=Acer Module
S:  SerialNumber=60D819F74101
C:* #Ifs= 4 Cfg#= 1 Atr=e0 MxPwr=  0mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  32 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  32 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  64 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  64 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=84(I) Atr=02(Bulk) MxPS=  32 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS=  32 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=01 Driver=(none)
Signed-off-by: NSteven Harms <sjharms@gmail.com>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

Command complete event for HCI_OP_USER_PASSKEY_NEG_REPLY would result
in calling handler function also for HCI_OP_LE_SET_SCAN_PARAM. This
could result in undefined behaviour.
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NGustavo Padovan <gustavo@padovan.org>

I keep getting the following messages on the log buffer:
[ 2167.097507] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.331305] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2281.332539] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.876605] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2329.877354] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2462.280756] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU
[ 2615.651689] ieee80211 phy0: brcms_c_dotxstatus: INTERMEDIATE but not AMPDU

From the code comment I understand that this something that can -
and does, quite frequently - happen.
Signed-off-by: NEldad Zack <eldad@fogrefinery.com>
Acked-by: Franky Lin<frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Under some circumstances, a PCI-based driver reports the following OOPs:

Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Oops: 0000 [#1] SMP
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Pid: 19627, comm: rmmod
Not tainted 3.2.9-2.fc16.x86_64 #1 LENOVO 05962RU/05962RU
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP:
0010:[<ffffffffa0418d39>]  [<ffffffffa0418d39>]
rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Process rmmod (pid:
19627, threadinfo ffff880050262000, task ffff8801156d5cc0)
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Stack:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000002
ffff8801176c2540 ffff880050263ca8 ffffffffa03348e7
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  0000000000000282
0000000180150014 ffff880050263fd8 ffff8801176c2810
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  ffff880050263bc8
ffffffff810550e2 00000000000002c0 ffff8801176c0d40
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Call Trace:
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  [<ffffffffa03348e7>]
_rtl_pci_rx_interrupt+0x187/0x650 [rtlwifi]
--snip--
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] Code: ff 09 d0 89 07 48
83 c4 08 5b 5d c3 66 0f 1f 44 00 00 55 48 89 e5 53 48 83 ec 08 66 66
66 66 90 40 84 f6 89 d3 74 13 84 d2 75 57 <8b> 07 48 83 c4 08 5b 5d c1
e8 1f c3 0f 1f 00 84 d2 74 ed 80 fa
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] RIP
[<ffffffffa0418d39>] rtl92ce_get_desc+0x19/0xd0 [rtl8192ce]
Mar 19 08:14:35 kvothe kernel: [ 6584.626011]  RSP <ffff880050263b58>
Mar 19 08:14:35 kvothe kernel: [ 6584.626011] CR2: 00000000000006e0
Mar 19 08:14:35 kvothe kernel: [ 6584.646491] ---[ end trace
8636c766dcfbe0e6 ]---

This oops is due to interrupts not being disabled in this particular path.
Reported-by: NDave Airlie <airlied@gmail.com>
Tested-by: NDave Airlie <airlied@gmail.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Driver incorrectly validates command completion: instead of waiting
for a command to be acknowledged it continues execution.  Most of the
time driver gets acknowledge of the command completion in a tasklet
before it executes the next one. But sometimes it sends the next
command before it gets acknowledge for the previous one. In such a
case one of the following error messages appear in the log:

Failed to send SYSTEM_CONFIG: Already sending a command.
Failed to send ASSOCIATE: Already sending a command.
Failed to send TX_POWER: Already sending a command.

After that you need to reload the driver to get it working again.

This bug occurs during roaming (reported by Sam Varshavchik)
https://bugzilla.redhat.com/show_bug.cgi?id=738508
and machine booting (reported by Tom Gundersen and Mads Kiilerich)
https://bugs.archlinux.org/task/28097
https://bugzilla.redhat.com/show_bug.cgi?id=802106

This patch doesn't fix the delay issue during firmware load.
But at least device now works as usual after boot.

Cc: stable@kernel.org
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ctx->vif is dereferenced in different part of iwlwifi code, so do not
nullify it.

This should address at least one of the possible reasons of WARNING at
iwlagn_mac_remove_interface, and perhaps some random crashes when
firmware reset is performed.

Cc: stable@vger.kernel.org
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f8588
(ath9k_hw: Cleanup TX power calculation for AR9287).

Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.

Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.

Fix this by adding the missing call of the helper
function.
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to unifying regulatory limit handling
commit ca2c68cc
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.

This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.

This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: NGabor Juhos <juhosg@openwrt.org>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add another vendor specific ID for Atheros AR3012

output of usb-devices:
T:  Bus=02 Lev=02 Prnt=02 Port=04 Cnt=01 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0cf3 ProdID=e004 Rev=00.02
S:  Manufacturer=Atheros Communications
S:  Product=Bluetooth USB Host Controller
S:  SerialNumber=Alaska Day 2006
C:  #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
I:  If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb

BugLink: https://bugs.launchpad.net/bugs/922715Signed-off-by: NAceLan Kao <acelan.kao@canonical.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The broken check leads to rate control attempting to use HT40 while
the driver is configured for HT20. This leads to interesting hardware
issues.

HT40 can only be used if the channel type is either HT40- or HT40+
and if the channel type of the cell matches the local type.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add Johannes Berg as the primary maintainer for iwlwifi driver
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Cooked monitor rx was recently changed to use ieee80211_add_rx_radiotap_header
instead of generating only limited radiotap information.
ieee80211_add_rx_radiotap_header assumes that FCS info is still present if
the hardware supports receiving it, however when cooked monitor rx packets
are processed, FCS info has already been stripped.
Fix this by adding an extra flag indicating FCS presence.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bcma should check for a fallback sprom every time it can not find a
sprom on the card itself or a normal external sprom mapped into the
memory of the chip. When otp sprom support was introduced it tried to
read out the sprom from the wireless chip also if no otp sprom was
available. This caused a Data bus error in bcma_sprom_get() when
reading out the sprom for the SoC.

This fixes a regression introduced in commit:

commit 10d8493c
Author: Arend van Spriel <arend@broadcom.com>
Date:   Tue Mar 6 15:50:48 2012 +0100

    bcma: add support for on-chip OTP memory used for SPROM storage

This patch was tested on a Netgear WNDR3400 (Broadcom BCM4718 SoC).
Reported-by: NNick Bowler <nbowler@elliptictech.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a key is non persistent then it should not be used in future
connections but it should be kept for current connection. And it
should be removed when connecion is removed.
Signed-off-by: NVishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This patch changes the return type of function hci_persistent_key
from int to bool because it makes more sense to return information
whether a key is persistent or not as a bool.
Signed-off-by: NVishal Agarwal <vishal.agarwal@stericsson.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The scratch register addresses have been changed for newer chips.
Since the old chip was never shipped and it will not be supported
any more, just update register addresses to support the new chips.

Cc: <stable@vger.kernel.org> # 3.2.y, 3.3.y
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJonathan Bither <jonbither@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When cross compiling ath5k for a Mips machine with kernel 3.2.14
the compilation fails with "/ath5k/ahb.c:231:12: error: 'THIS_MODULE' undeclared here (not in a function)"
Fix the build by including <linux/export.h>
Signed-off-by: NJonathan Bither <jonbither@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NLukasz Kucharczyk <lukasz.kucharczyk@tieto.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There have been reports about not being able to use access-points
on channel 12 and 13 or having connectivity issues when these channels
were part of the selected regulatory domain. Upon switching to these
channels the brcmsmac driver suspends the transmit dma fifos. This
patch resumes them upon handing over the first received beacon to
mac80211.

This patch is to be applied to the stable tree for kernel versions
3.2 and 3.3.

Cc: stable@vger.kernel.org
Tested-by: NFrancesco Saverio Schiavarelli <fschiava@libero.it>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NBrett Rudley <brudley@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Return type for lbs_auth_to_authtype() is changed from "u8" to
"int" to return negative error code correctly.
Also an error check is added in connect handler for invalid auth
type.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>