This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: NPavel Machek <pavel@denx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

626: CHECK: Alignment should match open parenthesis
 646: CHECK: Alignment should match open parenthesis
 655: CHECK: Alignment should match open parenthesis
 695: CHECK: Alignment should match open parenthesis
 729: CHECK: Alignment should match open parenthesis
 739: CHECK: Alignment should match open parenthesis
 976: WARNING: externs should be avoided in .c files
 1314: CHECK: Alignment should match open parenthesis
 1358: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1402: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 1521: CHECK: multiple assignments should be avoided
 1775: CHECK: Alignment should match open parenthesis
 1838: CHECK: multiple assignments should be avoided
 1843: CHECK: multiple assignments should be avoided
 1847: CHECK: multiple assignments should be avoided
 1850: WARNING: Missing a blank line after declarations
 1864: CHECK: Alignment should match open parenthesis
 1872: CHECK: braces {} should be used on all arms of this statement
 1906: CHECK: usleep_range is preferred over udelay
 2865: WARNING: networking block comments don't use an empty /* line, use /* Comment...
 3088: CHECK: Alignment should match open parenthesis
 total: 0 errors, 5 warnings, 16 checks, 3567 lines checked
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Basic deferred TX queue flushing infrastructure.

Over time, and specifically and more recently at the Networking
Workshop during Kernel SUmmit in Chicago, we have discussed the idea
of having some way to optimize transmits of multiple TX packets at
a time.

There are several areas of overhead that could be amortized with such
schemes.  One has to do with locking and transactional overhead, the
other has to do with device specific costs.

This patch set here is more aimed at device specific costs.

Typically a device queues up a packet in the TX queue and then has to
do something to have the device start processing that new entry.
Sometimes this is composed of doing an MMIO write to a "tail"
register, and in other cases it can involve something as expensive as
a hypervisor call.

The basic setup defined here is that when the driver supports deferred
TX queue flushing, ndo_start_xmit should no longer perform that
operation.  Instead a new operation, ndo_xmit_flush, should do it.

I have converted IGB and virtio_net as example initial users.  The IGB
conversion is tested, virtio_net is not but it does compile :-)

All ndo_start_xmit call sites have been abstracted behind a new helper
called netdev_start_xmit().

This just adds the infrastructure, it does not actually add any
instances of actually doing multiple ndo_start_xmit calls per
ndo_xmit_flush invocation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.

Both objdump and diff -w show no differences.

This patch removes some blank lines between the end of a function
definition and the EXPORT_SYMBOL_GPL macro in order to prevent
checkpatch warning that EXPORT_SYMBOL must immediately follow
a function.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.

Both objdump and diff -w show no differences.

This patch addresses structure definitions, specifically it cleanses the brace
placement and replaces spaces with tabs in a few places.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes no changes to the logic of the code but simply addresses
coding style issues as detected by checkpatch.

Both objdump and diff -w show no differences.

A number of items are addressed in this patch:
* Multiple spaces converted to tabs
* Spaces before tabs removed.
* Spaces in pointer typing cleansed (char *)foo etc.
* Remove space after sizeof
* Ensure spacing around comparators such as if statements.
Signed-off-by: NIan Morris <ipm@chirality.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This cuts down the number of debug information spit out by
the driver.
Signed-off-by: NDariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch addresses a couple of minor items, mostly addesssing
prandom_bytes(): 1) prandom_bytes{,_state}() should use size_t
for length arguments, 2) We can use put_unaligned() when filling
the array instead of open coding it [ perhaps some archs will
further benefit from their own arch specific implementation when
GCC cannot make up for it ], 3) Fix a typo, 4) Better use unsigned
int as type for getting the arch seed, 5) Make use of
prandom_u32_max() for timer slack.

Regarding the change to put_unaligned(), callers of prandom_bytes()
which internally invoke prandom_bytes_state(), don't bother as
they expect the array to be filled randomly and don't have any
control of the internal state what-so-ever (that's also why we
have periodic reseeding there, etc), so they really don't care.

Now for the direct callers of prandom_bytes_state(), which
are solely located in test cases for MTD devices, that is,
drivers/mtd/tests/{oobtest.c,pagetest.c,subpagetest.c}:

These tests basically fill a test write-vector through
prandom_bytes_state() with an a-priori defined seed each time
and write that to a MTD device. Later on, they set up a read-vector
and read back that blocks from the device. So in the verification
phase, the write-vector is being re-setup [ so same seed and
prandom_bytes_state() called ], and then memcmp()'ed against the
read-vector to check if the data is the same.

Akinobu, Lothar and I also tested this patch and it runs through
the 3 relevant MTD test cases w/o any errors on the nandsim device
(simulator for MTD devs) for x86_64, ppc64, ARM (i.MX28, i.MX53
and i.MX6):

  # modprobe nandsim first_id_byte=0x20 second_id_byte=0xac \
                     third_id_byte=0x00 fourth_id_byte=0x15
  # modprobe mtd_oobtest dev=0
  # modprobe mtd_pagetest dev=0
  # modprobe mtd_subpagetest dev=0

We also don't have any users depending directly on a particular
result of the PRNG (except the PRNG self-test itself), and that's
just fine as it e.g. allowed us easily to do things like upgrading
from taus88 to taus113.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Tested-by: NAkinobu Mita <akinobu.mita@gmail.com>
Tested-by: NLothar Waßmann <LW@KARO-electronics.de>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
net: Checksum offload changes - Part V

I am working on overhauling RX checksum offload. Goals of this effort
are:

- Specify what exactly it means when driver returns CHECKSUM_UNNECESSARY
- Preserve CHECKSUM_COMPLETE through encapsulation layers
- Don't do skb_checksum more than once per packet
- Unify GRO and non-GRO csum verification as much as possible
- Unify the checksum functions (checksum_init)
- Simplify code

What is in this fifth patch set:

- Added GRO checksum validation functions
- Call the GRO validations functions from TCP and GRE gro_receive
- Perform checksum verification in the UDP gro_receive path using
  GRO functions and add support for gro_receive in UDP6

Changes in V2:

- Change ip_summed to CHECKSUM_UNNECESSARY instead of moving it
  to CHECKSUM_COMPLETE from GRO checksum validation. This avoids
  performance penalty in checksumming bytes which are before the header
  GRO is at.

Please review carefully and test if possible, mucking with basic
checksum functions is always a little precarious :-)

----

Test results with this patch set are below. I did not notice any
performace regression.

Tests run:
   TCP_STREAM: super_netperf with 200 streams
   TCP_RR: super_netperf with 200 streams and -r 1,1

Device bnx2x (10Gbps):
   No GRE RSS hash (RX interrupts occur on one core)
   UDP RSS port hashing enabled.

* GRE with checksum with IPv4 encapsulated packets
  With fix:
    TCP_STREAM
        9.91% CPU utilization
        5163.78 Mbps
    TCP_RR
        50.64% CPU utilization
        219/347/502 90/95/99% latencies
        834103 tps
  Without fix:
    TCP_STREAM
        10.05% CPU utilization
        5186.22 tps
    TCP_RR
        49.70% CPU utilization
        227/338/486 90/95/99% latencies
        813450 tps

* GRE without checksum with IPv4 encapsulated packets
  With fix:
    TCP_STREAM
        10.18% CPU utilization
        5159 Mbps
    TCP_RR
        51.86% CPU utilization
        214/325/471 90/95/99% latencies
        865943 tps
  Without fix:
    TCP_STREAM
        10.26% CPU utilization
        5307.87 Mbps
    TCP_RR
        50.59% CPU utilization
        224/325/476 90/95/99% latencies
        846429 tps

*** Simulate device returns CHECKSUM_COMPLETE

* VXLAN with checksum
  With fix:
    TCP_STREAM
        13.03% CPU utilization
        9093.9 Mbps
    TCP_RR
        95.96% CPU utilization
        161/259/474 90/95/99% latencies
        1.14806e+06 tps
  Without fix:
    TCP_STREAM
        13.59% CPU utilization
        9093.97 Mbps
    TCP_RR
        93.95% CPU utilization
        160/259/484 90/95/99% latencies
        1.10262e+06 tps

* VXLAN without checksum
  With fix:
    TCP_STREAM
        13.28% CPU utilization
        9093.87 Mbps
    TCP_RR
        95.04% CPU utilization
        155/246/439 90/95/99% latencies
        1.15e+06 tps
  Without fix:
    TCP_STREAM
        13.37% CPU utilization
        9178.45 Mbps
    TCP_RR
        93.74% CPU utilization
        161/257/469 90/95/99% latencies
        1.1068e+06 Mbps
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In GRE demux if the GRE checksum pop rcv encapsulation so that any
encapsulated checksums are treated as tunnel checksums.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement GRO for UDPv6. Add UDP checksum verification in gro_receive
for both UDP4 and UDP6 calling skb_gro_checksum_validate_zero_check.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tcp[64]_gro_receive call skb_gro_checksum_validate to validate TCP
checksum in the gro context.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add inet_gro_compute_pseudo and ip6_gro_compute_pseudo. These are
the logical equivalents of inet_compute_pseudo and ip6_compute_pseudo
for GRO path. The IP header is taken from skb_gro_network_header.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add skb_gro_checksum_validate, skb_gro_checksum_validate_zero_check,
and skb_gro_checksum_simple_validate, and __skb_gro_checksum_complete.
These are the cognates of the normal checksum functions but are used
in the gro_receive path and operate on GRO related fields in sk_buffs.
Signed-off-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace open codings of (((u64) <x> * <y>) >> 32) with reciprocal_scale().
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drivers, and perhaps other entities we have not yet considered,
sometimes want to know how deep the protocol headers go before
deciding how large of an SKB to allocate and how much of the packet to
place into the linear SKB area.

For example, consider a driver which has a device which DMAs into
pools of pages and then tells the driver where the data went in the
DMA descriptor(s).  The driver can then build an SKB and reference
most of the data via SKB fragments (which are page/offset/length
triplets).

However at least some of the front of the packet should be placed into
the linear SKB area, which comes before the fragments, so that packet
processing can get at the headers efficiently.  The first thing each
protocol layer is going to do is a "pskb_may_pull()" so we might as
well aggregate as much of this as possible while we're building the
SKB in the driver.

Part of supporting this is that we don't have an SKB yet, so we want
to be able to let the flow dissector operate on a raw buffer in order
to compute the offset of the end of the headers.

So now we have a __skb_flow_dissect() which takes an explicit data
pointer and length.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
net: phy: bcm7xxx: APD and EEE support

This patch series enables Auto-power down and EEE for the BCM7xxx integrated
Gigabit PHYs.

I also put a fix for the fixed PHY that would allow clause 45 over clause 22
reads/writes but would return bogus data by using e.g: ethtool --show-eee
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm Gigabit PHY on BCM7xxx chips comes out of reset with absolutely
no EEE capabilities, such that we would actually return that we do not
support EEE when accessing 3.20 (MDIO_PCS_EEE_ABLE) registers.

Poke through the vendor-specific C45 register to enable EEE globally at
the PHY level, and advertise supported EEE modes.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Internal PHYs do not have any specific phy_interface_t defined because
they are within an Ethernet MAC or a larger IC, they will fail the early
check in phy_init_eee(). Allow these PHYs to proceed with EEE
initialization and report error/success by checking the standard C45
EEE-related registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHY drivers might need to access Clause 45 registers in Clause 22
compatibility mode to e.g: properly advertise EEE support when disabled
by default.

Export these two helper functions: phy_read_mmd_indirect() and
phy_write_mmd_indirect() for drivers to use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The fixed PHY driver does not properly emulate Clause 45 over Clause 22
MDIO reads, and as such, will return bogus values when we access such
registers.

Return an error when accessing these registers in order to prevent
advertising bogus capabilities such as EEE support and such.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 28nm process BCM7xxx internal Gigabit PHYs all support automatic
power down, turn on that feature as part of the configuration
initialization callback.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The shadow register 0x1C is used both by the BCM54xxx PHYs and the
BCM7xxx internal PHYs, move the accessors to a common location so both
drivers can use them.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 439d39a9 ("net: phy: broadcom:
extract register definitions") added a bunch of registers to brcmphy.h
but left some to broadcom.c, move all of them to the header file since
the BCM54xx and BCM7xxx PHY drivers do share all of these registers.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: Merge port and socket layer code

After the removal of the TIPC native interface, there is no reason to
keep a distinction between a "generic" port layer and a "specific"
socket layer in the code. Throughout the last months, we have posted
several series that aimed at facilitating removal of the port layer,
and in particular the port_lock spinlock, which in reality duplicates
the role normally kept by lock_sock()/bh_lock_sock().

In this series, we finalize this work, by making a significant number of
changes to the link, node, port and socket code, all with the aim of
reducing dependencies between the layers. In the final commits, we then
remove the port spinlock, port.c and port.h altogether.

After this series, we have a socket layer that has only few dependencies
to the rest of the stack, so that it should be possible to continue
cleanups of its code without significantly affecting other code.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We complete the merging of the port and socket layer by aggregating
the fields of struct tipc_port directly into struct tipc_sock, and
moving the combined structure into socket.c.

We also move all functions and macros that are not any longer
exposed to the rest of the stack into socket.c, and rename them
accordingly.

Despite the size of this commit, there are no functional changes.
We have only made such changes that are necessary due of the removal
of struct tipc_port.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reference table is now 'socket aware' instead of being generic,
and has in reality become a socket internal table. In order to be
able to minimize the API exposed by the socket layer towards the rest
of the stack, we now move the reference table definitions and functions
into the file socket.c, and rename the functions accordingly.

There are no functional changes in this commit.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.

We move struct tipc_port and some macros to socket.h.

Finally, we remove the file port.h.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this commit, we move the remaining functions in port.c to
socket.c, and give them new names that correspond to their new
location. We then remove the file port.c.

There are only cosmetic changes to the moved functions.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In previous commits we have reduced usage of port_lock to a minimum,
and complemented it with usage of bh_lock_sock() at the remaining
locations. The purpose has been to remove this lock altogether, since
it largely duplicates the role of bh_lock_sock. We are now ready to do
this.

However, we still need to protect the BH callers from inadvertent
release of the socket while they hold a reference to it. We do this by
replacing port_lock by a combination of a rw-lock protecting the
reference table as such, and updating the socket reference counter while
the socket is referenced from BH. This technique is more standard and
comprehensible than the previous approach, and turns out to have a
positive effect on overall performance.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make tipc_sock the only entity referencable from other
parts of the stack, we add a tipc_sock pointer instead of a tipc_port
pointer to the registry. As a consequence, we also let the function
tipc_port_lock() return a pointer to a tipc_sock instead  of a tipc_port.
We keep the function's name for now, since the lock still is owned by
the port.

This is another step in the direction of eliminating port_lock, replacing
its usage with lock_sock() and bh_lock_sock().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The functions tipc_port_get_ports() and tipc_port_reinit() scan over
all sockets/ports to access each of them. This is done by using a
dedicated linked list, 'tipc_socks' where all sockets are members. The
list is in turn protected by a spinlock, 'port_list_lock', while each
socket is locked by using port_lock at the moment of access.

In order to reduce complexity and risk of deadlock, we want to get
rid of the linked list and the accompanying spinlock.

This is what we do in this commit. Instead of the linked list, we use
the port registry to scan across the sockets. We also add usage of
bh_lock_sock() inside the scope of port_lock in both functions, as a
preparation for the complete removal of port_lock.

Finally, we move the functions from port.c to socket.c, and rename them
to tipc_sk_sock_show() and tipc_sk_reinit() repectively.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the latest changes to the socket/port layer the existence of
the functions tipc_port_init() and tipc_port_destroy() cannot be
justified. They are both called only once, from tipc_sk_create() and
tipc_sk_delete() respectively, and their functionality can better be
merged into the latter two functions.

This also entails that all remaining references to port_lock now are
made from inside socket.c, something that will make it easier to remove
this lock.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function tipc_acknowledge() is a remnant from the obsolete native
API. Currently, it grabs port_lock, before building an acknowledge
message and sending it to the peer.

Since all access to socket members now is protected by the socket lock,
it has become unnecessary to grab port_lock here.

In this commit, we remove the usage of port_lock, simplify the
function, and move it to socket.c, renaming it to tipc_sk_send_ack().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tipc_port_connect()/tipc_port_disconnect() are remnants of the obsolete
native API. Their only task is to grab port_lock and call the functions
__tipc_port_connect()/__tipc_port_disconnect() respectively, which will
perform the actual state change.

Since socket/port exection now is single-threaded the use of port_lock
is not needed any more, so we can safely replace the two functions with
their lock-free counterparts.

In this commit, we remove the two functions. Furthermore, the contents
of __tipc_port_disconnect() is so trivial that we choose to eliminate
that function too, expanding its functionality into tipc_shutdown().
__tipc_port_connect() is simplified, moved to socket.c, and given the
more correct name tipc_sk_finish_conn(). Finally, we eliminate the
function auto_connect(), and expand its contents into filter_connect().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tipc_port_shutdown() is a remnant from the now obsolete native
interface. As such it grabs port_lock in order to protect itself
from concurrent BH processing.

However, after the recent changes to the port/socket upcalls, sockets
are now basically single-threaded, and all execution, except the read-only
tipc_sk_timer(), is executing within the protection of lock_sock(). So
the use of port_lock is not needed here.

In this commit we eliminate the whole function, and merge it into its
only caller, tipc_shutdown().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NErik Hugne <erik.hugne@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>