Lazy save and restore of FP/Altivec means that a userspace process can
be sent to userspace with FP or Altivec disabled and loaded only as
required (by way of an FP/Altivec unavailable exception). Transactional
Memory complicates this situation as a transaction could be started
without FP/Altivec being loaded up. This causes the hardware to
checkpoint incorrect registers. Handling FP/Altivec unavailable
exceptions while a thread is transactional requires a reclaim and
recheckpoint to ensure the CPU has correct state for both sets of
registers.

Lazy save and restore of FP/Altivec cannot be done if a process is
transactional. If a facility was enabled it must remain enabled whenever
a thread is transactional.

Commit dc16b553 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use") ensures that the facilities are always
enabled if a thread is transactional. A bug in the introduced code may
cause it to inadvertently enable a facility that was (and should remain)
disabled. The problem with this extraneous enablement is that the
registers for the erroneously enabled facility have not been correctly
recheckpointed - the recheckpointing code assumed the facility would
remain disabled.

Further compounding the issue, the transactional {fp,altivec,vsx}
unavailable code has been incorrectly using the MSR to enable
facilities. The presence of the {FP,VEC,VSX} bit in the regs->msr simply
means if the registers are live on the CPU, not if the kernel should
load them before returning to userspace. This has worked due to the bug
mentioned above.

This causes transactional threads which return to their failure handler
to observe incorrect checkpointed registers. Perhaps an example will
help illustrate the problem:

A userspace process is running and uses both FP and Altivec registers.
This process then continues to run for some time without touching
either sets of registers. The kernel subsequently disables the
facilities as part of lazy save and restore. The userspace process then
performs a tbegin and the CPU checkpoints 'junk' FP and Altivec
registers. The process then performs a floating point instruction
triggering a fp unavailable exception in the kernel.

The kernel then loads the FP registers - and only the FP registers.
Since the thread is transactional it must perform a reclaim and
recheckpoint to ensure both the checkpointed registers and the
transactional registers are correct. It then (correctly) enables
MSR[FP] for the process. Later (on exception exist) the kernel also
(inadvertently) enables MSR[VEC]. The process is then returned to
userspace.

Since the act of loading the FP registers doomed the transaction we know
CPU will fail the transaction, restore its checkpointed registers, and
return the process to its failure handler. The problem is that we're
now running with Altivec enabled and the 'junk' checkpointed registers
are restored. The kernel had only recheckpointed FP.

This patch solves this by only activating FP/Altivec if userspace was
using them when it entered the kernel and not simply if the process is
transactional.

Fixes: dc16b553 ("powerpc: Always restore FPU/VEC/VSX if hardware
transactional memory in use")
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This interface is inefficient and deprecated because of the y2038
overflow.

ktime_get_seconds() is an appropriate replacement here, since it
has sufficient granularity but is more efficient and uses monotonic
time.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NAndrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently when we take a TM Bad Thing program check exception, we
search the bug table to see if the program check was generated by a
WARN/WARN_ON etc.

That makes no sense, the WARN macros use trap instructions, which
should never generate a TM Bad Thing exception. If they ever did that
would be a bug and we should oops.

We do have some hand-coded bugs in tm.S, using EMIT_BUG_ENTRY, but
those are all BUGs not WARNs, and they all use trap instructions
anyway. Almost certainly this check was incorrectly copied from the
REASON_TRAP handling in the same function.

Remove it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Acked-By: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

CONFIG_PPC_STD_MMU_64 indicates support for the "standard" powerpc MMU
on 64-bit CPUs. The "standard" MMU refers to the hash page table MMU
found in "server" processors, from IBM mainly.

Currently CONFIG_PPC_STD_MMU_64 is == CONFIG_PPC_BOOK3S_64. While it's
annoying to have two symbols that always have the same value, it's not
quite annoying enough to bother removing one.

However with the arrival of Power9, we now have the situation where
CONFIG_PPC_STD_MMU_64 is enabled, but the kernel is running using the
Radix MMU - *not* the "standard" MMU. So it is now actively confusing
to use it, because it implies that code is disabled or inactive when
the Radix MMU is in use, however that is not necessarily true.

So s/CONFIG_PPC_STD_MMU_64/CONFIG_PPC_BOOK3S_64/, and do some minor
formatting updates of some of the affected lines.

This will be a pain for backports, but c'est la vie.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The last user of CPU_FTR_ICSWX was removed in commit
6ff4d3e9 ("powerpc: Remove old unused icswx based coprocessor
support"), so free the bit up for future use.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

When returning from an exception to a soft-enabled context, pending
IRQs are replayed but IRQ tracing is not reset, so a number of them
can get chained together into the same IRQ-disabled trace.

Fix this by having __check_irq_replay re-set IRQ trace. This is
conceptually where we respond to the next interrupt, so it fits the
semantics of the IRQ tracer.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If the host takes a system reset interrupt while a guest is running,
the CPU must exit the guest before processing the host exception
handler.

After this patch, taking a sysrq+x with a CPU running in a guest
gives a trace like this:

   cpu 0x27: Vector: 100 (System Reset) at [c000000fdf5776f0]
       pc: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
       lr: c008000010158b80: kvmppc_run_core+0x16b8/0x1ad0 [kvm_hv]
       sp: c000000fdf577850
      msr: 9000000002803033
     current = 0xc000000fdf4b1e00
     paca    = 0xc00000000fd4d680	 softe: 3	 irq_happened: 0x01
       pid   = 6608, comm = qemu-system-ppc
   Linux version 4.14.0-rc7-01489-g47e1893a404a-dirty #26 SMP
   [c000000fdf577a00] c008000010159dd4 kvmppc_vcpu_run_hv+0x3dc/0x12d0 [kvm_hv]
   [c000000fdf577b30] c0080000100a537c kvmppc_vcpu_run+0x44/0x60 [kvm]
   [c000000fdf577b60] c0080000100a1ae0 kvm_arch_vcpu_ioctl_run+0x118/0x310 [kvm]
   [c000000fdf577c00] c008000010093e98 kvm_vcpu_ioctl+0x530/0x7c0 [kvm]
   [c000000fdf577d50] c000000000357bf8 do_vfs_ioctl+0xd8/0x8c0
   [c000000fdf577df0] c000000000358448 SyS_ioctl+0x68/0x100
   [c000000fdf577e30] c00000000000b220 system_call+0x58/0x6c
   --- Exception: c01 (System Call) at 00007fff76868df0
   SP (7fff7069baf0) is in userspace

Fixes: e36d0a2e ("powerpc/powernv: Implement NMI IPI with OPAL_SIGNAL_SYSTEM_RESET")
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Back in 2008 we added support for "fast little-endian switch" in the
syscall path. This added a special case syscall number 0x1ebe, which
is caught very early in the system call exception and switches endian
with as little overhead as possible. See commit 745a14cc
("[POWERPC] Add fast little-endian switch system call") for full
details.

Although it is fast, it's also completely non standard. The "syscall
number" is out of the range of normal syscalls, it can't be traced or
audited, and it's a bit of a wart. To the best of our knowledge it was
only used by one program, now long since discontinued.

So in an effort to shake out any current users, put it behind a config
option, and make it default n. If anyone *is* using it they can
quickly reinstate it with a rebuild, and we can flip it to default y.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

So we can #ifdef them in the next patch.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Unfortunately userspace can construct a sigcontext which enables
suspend. Thus userspace can force Linux into a path where trechkpt is
executed.

This patch blocks this from happening on POWER9 by sanity checking
sigcontexts passed in.

ptrace doesn't have this problem as only MSR SE and BE can be changed
via ptrace.

This patch also adds a number of WARN_ON()s in case we ever enter
suspend when we shouldn't. This should not happen, but if it does the
symptoms are soft lockup warnings which are not obviously TM related,
so the WARN_ON()s should make it obvious what's happening.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some Power9 revisions can run in a mode where TM operates without
suspended state. If we find ourself on a CPU that might be in this
mode, we query OPAL to check, and if so we reenable TM in CPU
features, and enable a new user feature to signal to userspace that we
are in this mode.

We do not enable the "normal" user feature, PPC_FEATURE2_HTM, but we
do enable PPC_FEATURE2_HTM_NOSC because that indicates to userspace
that the kernel will abort transactions on syscall entry, which is
true regardless of the suspend mode.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently the kernel relies on firmware to inform it whether or not the
CPU supports HTM and as long as the kernel was built with
CONFIG_PPC_TRANSACTIONAL_MEM=y then it will allow userspace to make
use of the facility.

There may be situations where it would be advantageous for the kernel
to not allow userspace to use HTM, currently the only way to achieve
this is to recompile the kernel with CONFIG_PPC_TRANSACTIONAL_MEM=n.

This patch adds a simple commandline option so that HTM can be
disabled at boot time.
Signed-off-by: NCyril Bur <cyrilbur@gmail.com>
[mpe: Simplify to a bool, move to prom.c, put doco in the right place.
 Always disable, regardless of initial state, to avoid user confusion.]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This reverts commit 94a04bc2.

In order to run HPT guests on a radix POWER9 host, we will have to run
the host in single-threaded mode, because POWER9 processors do not
currently support running some threads of a core in HPT mode while
others are in radix mode ("mixed mode").

That means that we will need the same mechanisms that are used on
POWER8 to make the secondary threads available to KVM, which were
disabled on POWER9 by commit 94a04bc2.
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If we are in user space and hit a UE error, we now have the
basic infrastructure to walk the page tables and find out
the effective address that was accessed, since the DAR
is not valid.

We use a work_queue content to hookup the bad pfn, any
other context causes problems, since memory_failure itself
can call into schedule() via lru_drain_ bits.

We could probably poison the struct page to avoid a race
between detection and taking corrective action.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Hookup instruction errors (UE) for memory offling via memory_failure()
in a manner similar to load/store errors (derror). Since we have access
to the NIP, the conversion is a one step process in this case.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Extract physical_address for UE errors by walking the page
tables for the mm and address at the NIP, to extract the
instruction. Then use the instruction to find the effective
address via analyse_instr().

We might have page table walking races, but we expect them to
be rare, the physical address extraction is best effort. The idea
is to then hook up this infrastructure to memory failure eventually.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use the same alignment as Effective address.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

There are no users of get_mce_fault_addr() since commit
1363875b ("powerpc/64s: fix handling of non-synchronous machine
checks") removed the last usage.
Signed-off-by: NBalbir Singh <bsingharora@gmail.com>
Reviewed-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use WARN_ON(), while running out of stubs in stub_for_addr()
and abort loading of the module instead of BUG_ON().
Signed-off-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a check for p->state == TASK_RUNNING so that any wake-ups on
task_struct p in the interim lead to 0 being returned by get_wchan().
Signed-off-by: NKautuk Consul <kautuk.consul.1980@gmail.com>
[mpe: Confirmed other architectures do similar]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix a circa 2005 FIXME by implementing a check to ensure that we
actually got into the jprobe break handler() due to the trap in
jprobe_return().
Acked-by: NMasami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

KPROBES_SANITY_TEST throws the below splat when CONFIG_PREEMPT is
enabled:

  Kprobe smoke test: started
  DEBUG_LOCKS_WARN_ON(val > preempt_count())
  ------------[ cut here ]------------
  WARNING: CPU: 19 PID: 1 at kernel/sched/core.c:3094 preempt_count_sub+0xcc/0x140
  Modules linked in:
  CPU: 19 PID: 1 Comm: swapper/0 Not tainted 4.13.0-rc7-nnr+ #97
  task: c0000000fea80000 task.stack: c0000000feb00000
  NIP:  c00000000011d3dc LR: c00000000011d3d8 CTR: c000000000a090d0
  REGS: c0000000feb03400 TRAP: 0700   Not tainted  (4.13.0-rc7-nnr+)
  MSR:  8000000000021033 <SF,ME,IR,DR,RI,LE>  CR: 28000282  XER: 00000000
  CFAR: c00000000015aa18 SOFTE: 0
  <snip>
  NIP preempt_count_sub+0xcc/0x140
  LR  preempt_count_sub+0xc8/0x140
  Call Trace:
    preempt_count_sub+0xc8/0x140 (unreliable)
    kprobe_handler+0x228/0x4b0
    program_check_exception+0x58/0x3b0
    program_check_common+0x16c/0x170
    --- interrupt: 0 at kprobe_target+0x8/0x20
                     LR = init_test_probes+0x248/0x7d0
    kp+0x0/0x80 (unreliable)
    livepatch_handler+0x38/0x74
    init_kprobes+0x1d8/0x208
    do_one_initcall+0x68/0x1d0
    kernel_init_freeable+0x298/0x374
    kernel_init+0x24/0x160
    ret_from_kernel_thread+0x5c/0x70
  Instruction dump:
  419effdc 3d22001b 39299240 81290000 2f890000 409effc8 3c82ffcb 3c62ffcb
  3884bc68 3863bc18 4803d5fd 60000000 <0fe00000> 4bffffa8 60000000 60000000
  ---[ end trace 432dd46b4ce3d29f ]---
  Kprobe smoke test: passed successfully

The issue is that we aren't disabling preemption in
kprobe_ftrace_handler(). Disable it.

Fixes: ead514d5 ("powerpc/kprobes: Add support for KPROBES_ON_FTRACE")
Acked-by: NMasami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
[mpe: Trim oops a little for formatting]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Kamalesh pointed out that we are getting the below call traces with
livepatched functions when we enable CONFIG_PREEMPT:

[  495.470721] BUG: using __this_cpu_read() in preemptible [00000000] code: cat/8394
[  495.471167] caller is is_current_kprobe_addr+0x30/0x90
[  495.471171] CPU: 4 PID: 8394 Comm: cat Tainted: G              K 4.13.0-rc7-nnr+ #95
[  495.471173] Call Trace:
[  495.471178] [c00000008fd9b960] [c0000000009f039c] dump_stack+0xec/0x160 (unreliable)
[  495.471184] [c00000008fd9b9a0] [c00000000059169c] check_preemption_disabled+0x15c/0x170
[  495.471187] [c00000008fd9ba30] [c000000000046460] is_current_kprobe_addr+0x30/0x90
[  495.471191] [c00000008fd9ba60] [c00000000004e9a0] ftrace_call+0x1c/0xb8
[  495.471195] [c00000008fd9bc30] [c000000000376fd8] seq_read+0x238/0x5c0
[  495.471199] [c00000008fd9bcd0] [c0000000003cfd78] proc_reg_read+0x88/0xd0
[  495.471203] [c00000008fd9bd00] [c00000000033e5d4] __vfs_read+0x44/0x1b0
[  495.471206] [c00000008fd9bd90] [c0000000003402ec] vfs_read+0xbc/0x1b0
[  495.471210] [c00000008fd9bde0] [c000000000342138] SyS_read+0x68/0x110
[  495.471214] [c00000008fd9be30] [c00000000000bc6c] system_call+0x58/0x6c

Commit c05b8c44 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes") introduced a helper is_current_kprobe_addr() to help determine
if the current function has been livepatched or if it has a jprobe
installed, both of which modify the NIP. This was subsequently renamed
to __is_active_jprobe().

In the case of a jprobe, kprobe_ftrace_handler() disables pre-emption
before calling into setjmp_pre_handler() which returns without disabling
pre-emption. This is done to ensure that the jprobe handler won't
disappear beneath us if the jprobe is unregistered between the
setjmp_pre_handler() and the subsequent longjmp_break_handler() called
from the jprobe handler. Due to this, we can use __this_cpu_read() in
__is_active_jprobe() with the pre-emption check as we know that
pre-emption will be disabled.

However, if this function has been livepatched, we are still doing this
check and when we do so, pre-emption won't necessarily be disabled. This
results in the call trace shown above.

Fix this by only invoking __is_active_jprobe() when pre-emption is
disabled. And since we now guard this within a pre-emption check, we can
instead use raw_cpu_read() to get the current_kprobe value skipping the
check done by __this_cpu_read().

Fixes: c05b8c44 ("powerpc/kprobes: Skip livepatch_handler() for jprobes")
Reported-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Tested-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In commit c05b8c44 ("powerpc/kprobes: Skip livepatch_handler() for
jprobes"), we added a helper is_current_kprobe_addr() to help detect if
the modified regs->nip was due to a jprobe or livepatch. Masami felt
that the function name was not quite clear. To that end, this patch
renames is_current_kprobe_addr() to __is_active_jprobe() and adds a
comment to (hopefully) better clarify the purpose of this helper. The
helper has also now been moved to kprobes-ftrace.c so that it is only
available for KPROBES_ON_FTRACE.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Currently, we disable instruction emulation if emulate_step() fails for
any reason. However, such failures could be transient and specific to a
particular run. Instead, only disable instruction emulation if we have
never been able to emulate this. If we had emulated this instruction
successfully at least once, then we single step only this probe hit and
continue to try emulating the instruction in subsequent probe hits.
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

1. This is only used in kprobes.c, so make it static.
2. Remove the un-necessary (ret == 0) comparison in the else clause.
Reviewed-by: NMasami Hiramatsu <mhiramat@kernel.org>
Reviewed-by: NKamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This code is used at boot and machine checks, so it should be using
early_radix_enabled() (which is usable any time).
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

It is possible to wake from idle due to a system reset exception, in
which case the CPU takes a system reset interrupt to wake from idle,
with system reset as the wakeup reason.

The regular (not idle wakeup) system reset interrupt handler must be
invoked in this case, otherwise the system reset interrupt is lost.

Handle the system reset interrupt immediately after CPU state has been
restored.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In xmon, touch_nmi_watchdog() is not expected to be checking that
other CPUs have not touched the watchdog, so the code will just call
touch_nmi_watchdog() once before re-enabling hard interrupts.

Just update our CPU's state, and ignore apparently stuck SMP threads.

Arguably touch_nmi_watchdog should check for SMP lockups, and callers
should be fixed, but that's not trivial for the input code of xmon.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

If sysctl_hardlockup_all_cpu_backtrace is enabled, there is no need to
IPI stuck CPUs for backtrace before trigger_allbutself_cpu_backtrace(),
which does the same thing again.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

The SMP watchdog will detect locked CPUs and IPI them to print a
backtrace and registers. If panic on hard lockup is enabled, do not
panic from this handler, because that can cause recursion into the IPI
layer during the panic.

The caller already panics in this case.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

POWER9 DD2.1 and earlier has an issue where some cache inhibited
vector load will return bad data. The workaround is two part, one
firmware/microcode part triggers HMI interrupts when hitting such
loads, the other part is this patch which then emulates the
instructions in Linux.

The affected instructions are limited to lxvd2x, lxvw4x, lxvb16x and
lxvh8x.

When an instruction triggers the HMI, all threads in the core will be
sent to the HMI handler, not just the one running the vector load.

In general, these spurious HMIs are detected by the emulation code and
we just return back to the running process. Unfortunately, if a
spurious interrupt occurs on a vector load that's to normal memory we
have no way to detect that it's spurious (unless we walk the page
tables, which is very expensive). In this case we emulate the load but
we need do so using a vector load itself to ensure 128bit atomicity is
preserved.

Some additional debugfs emulated instruction counters are added also.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
[mpe: Switch CONFIG_PPC_BOOK3S_64 to CONFIG_VSX to unbreak the build]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove the post_init callback which is only used
by powernv, we can just call it explicitly from
the powernv code.

This partially kills the ability to "disable" eeh at
runtime via debugfs as this was calling that same
callback again, but this is both unused and broken
in several ways. If we want to revive it, we need
to create a dedicated enable/disable callback on the
backend that does the right thing.

Let the bulk of eeh initialize normally at
core_initcall() like it does on pseries by removing
the hack in eeh_init() that delays it.

Instead we make sure our eeh->probe cleanly bails
out of the PEs haven't been created yet and we force
a re-probe where we used to call eeh_init() again.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Otherwise we end up not yet having computed the right diag data size
on powernv where EEH initialization is delayed, thus causing memory
corruption later on when calling OPAL.

Fixes: 5cb1f8fd ("powerpc/powernv/pci: Dynamically allocate PHB diag data")
Cc: stable@vger.kernel.org # v4.13+
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NRussell Currey <ruscur@russell.cc>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Optprobes depended on an updated regs->nip from analyse_instr() to
identify the location to branch back from the optprobes trampoline.
However, since commit 3cdfcbfd ("powerpc: Change analyse_instr so
it doesn't modify *regs"), analyse_instr() doesn't update the registers
anymore.  Due to this, we end up branching back from the optprobes
trampoline to the same branch into the trampoline resulting in a loop.

Fix this by calling out to emulate_update_regs() before using the nip.
Additionally, explicitly compare the return value from analyse_instr()
to 1, rather than just checking for !0 so as to guard against any
future changes to analyse_instr() that may result in -1 being returned
in more scenarios.

Fixes: 3cdfcbfd ("powerpc: Change analyse_instr so it doesn't modify *regs")
Signed-off-by: NNaveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Commit cd63f3cf ("powerpc/tm: Fix saving of TM SPRs in core dump")
added code to access TM SPRs in flush_tmregs_to_thread(). However
flush_tmregs_to_thread() does not check if TM feature is available on
CPU before trying to access TM SPRs in order to copy live state to
thread structures. flush_tmregs_to_thread() is indeed guarded by
CONFIG_PPC_TRANSACTIONAL_MEM but it might be the case that kernel
was compiled with CONFIG_PPC_TRANSACTIONAL_MEM enabled and ran on
a CPU without TM feature available, thus rendering the execution
of TM instructions that are treated by the CPU as illegal instructions.

The fix is just to add proper checking in flush_tmregs_to_thread()
if CPU has the TM feature before accessing any TM-specific resource,
returning immediately if TM is no available on the CPU. Adding
that checking in flush_tmregs_to_thread() instead of in places
where it is called, like in vsr_get() and vsr_set(), is better because
avoids the same problem cropping up elsewhere.

Cc: stable@vger.kernel.org # v4.13+
Fixes: cd63f3cf ("powerpc/tm: Fix saving of TM SPRs in core dump")
Signed-off-by: NGustavo Romero <gromero@linux.vnet.ibm.com>
Reviewed-by: NCyril Bur <cyrilbur@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This fixes the emulation of the dcbz instruction in the alignment
interrupt handler.  The error was that we were comparing just the
instruction type field of op.type rather than the whole thing,
and therefore the comparison "type != CACHEOP + DCBZ" was always
true.

Fixes: 31bfdb03 ("powerpc: Use instruction emulation infrastructure to handle alignment faults")
Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
Tested-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Tested-by: NChristian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

GFP_TEMPORARY was introduced by commit e12ba74d ("Group short-lived
and reclaimable kernel allocations") along with __GFP_RECLAIMABLE.  It's
primary motivation was to allow users to tell that an allocation is
short lived and so the allocator can try to place such allocations close
together and prevent long term fragmentation.  As much as this sounds
like a reasonable semantic it becomes much less clear when to use the
highlevel GFP_TEMPORARY allocation flag.  How long is temporary? Can the
context holding that memory sleep? Can it take locks? It seems there is
no good answer for those questions.

The current implementation of GFP_TEMPORARY is basically GFP_KERNEL |
__GFP_RECLAIMABLE which in itself is tricky because basically none of
the existing caller provide a way to reclaim the allocated memory.  So
this is rather misleading and hard to evaluate for any benefits.

I have checked some random users and none of them has added the flag
with a specific justification.  I suspect most of them just copied from
other existing users and others just thought it might be a good idea to
use without any measuring.  This suggests that GFP_TEMPORARY just
motivates for cargo cult usage without any reasoning.

I believe that our gfp flags are quite complex already and especially
those with highlevel semantic should be clearly defined to prevent from
confusion and abuse.  Therefore I propose dropping GFP_TEMPORARY and
replace all existing users to simply use GFP_KERNEL.  Please note that
SLAB users with shrinkers will still get __GFP_RECLAIMABLE heuristic and
so they will be placed properly for memory fragmentation prevention.

I can see reasons we might want some gfp flag to reflect shorterm
allocations but I propose starting from a clear semantic definition and
only then add users with proper justification.

This was been brought up before LSF this year by Matthew [1] and it
turned out that GFP_TEMPORARY really doesn't have a clear semantic.  It
seems to be a heuristic without any measured advantage for most (if not
all) its current users.  The follow up discussion has revealed that
opinions on what might be temporary allocation differ a lot between
developers.  So rather than trying to tweak existing users into a
semantic which they haven't expected I propose to simply remove the flag
and start from scratch if we really need a semantic for short term
allocations.

[1] http://lkml.kernel.org/r/20170118054945.GD18349@bombadil.infradead.org

[akpm@linux-foundation.org: fix typo]
[akpm@linux-foundation.org: coding-style fixes]
[sfr@canb.auug.org.au: drm/i915: fix up]
  Link: http://lkml.kernel.org/r/20170816144703.378d4f4d@canb.auug.org.au
Link: http://lkml.kernel.org/r/20170728091904.14627-1-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NMel Gorman <mgorman@suse.de>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

First, number of CPUs can't be negative number.

Second, different signnnedness leads to suboptimal code in the following
cases:

1)
	kmalloc(nr_cpu_ids * sizeof(X));

"int" has to be sign extended to size_t.

2)
	while (loff_t *pos < nr_cpu_ids)

MOVSXD is 1 byte longed than the same MOV.

Other cases exist as well. Basically compiler is told that nr_cpu_ids
can't be negative which can't be deduced if it is "int".

Code savings on allyesconfig kernel: -3KB

	add/remove: 0/0 grow/shrink: 25/264 up/down: 261/-3631 (-3370)
	function                                     old     new   delta
	coretemp_cpu_online                          450     512     +62
	rcu_init_one                                1234    1272     +38
	pci_device_probe                             374     399     +25

				...

	pgdat_reclaimable_pages                      628     556     -72
	select_fallback_rq                           446     369     -77
	task_numa_find_cpu                          1923    1807    -116

Link: http://lkml.kernel.org/r/20170819114959.GA30580@avx2Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>