ffuart is available on cm-x300 only with pxa300.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

The NAND support is implemented through the gen_nand driver.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Add supported for PCF8574A GPIO expander and LEDs attached to it.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This driver adds support for the on-board CF socket.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Modularize components of the Balloon3 board.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Logically separate parts of the file that are handled by one particular driver.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Improve formating so checkpatch passes. Also, change some function and variable
names to make the naming consistent.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:

1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
   similar code. The kernel size will grow by a few kb now, but the file is much
   more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

This contains common code for Palm LD, TX, T5, Z72, Treo680, Centro
This code also adds PMIC support for all the devices,
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>

Only a small part of used code is moved into sharpsl_pm.h.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

READ_GPIO_BIT() is no way generic by accessing GPIO registers directly,
replace it with gpio_get_value().
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

IDE_PXA_CF doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Acked-by: NJuergen Schindele <schindele@nentec.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

XSCALE_CACHE_ERRATA doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

CORGI_SSP_DEPRECATED doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Acked-by: NKristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

ARCH_GUMSTIX_ORIG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Acked-by: NJaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

BACKLIGHT_CORGI was later renamed to BACKLIGHT_GENERIC and has not been
used since then. As it's now safe to completely transition to LCD_CORGI
driver, which incorprates both the LCD and backlight device.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

SHARP_LOCOMO doesn't exist in Kconfig, therefore replacing all
references for it with SHARP_LOCOMO in the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The latest PXA3xx DM has enabled 312MHz for the HSS bus,
which allows x24 multiplier.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Add bit definitions of the CPR register of the SCOOP chip into scoop.h. Also,
cleanup the GPCR definitions to match coding style.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Add support for PXA UDC.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Register TPS65021 regulator in Zipit Z2.
Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

With kexec-based kernel boot loader on Zaurus, the machine ID is
actually correctly passed, and head-sharpsl.S is not necessary.
Introduce PXA_SHARPSL_DETECT_MACH_ID, and include head-sharpsl.S
only when that's explicitly enabled.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

1. TOSA related un-hidden options moved to right under MACH_TOSA
2. SHARPSL_PM related hidden options moved to the end of Kconfig
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

With a correct dev->dma_mask before calling dmabounce_register_dev(),
dma_needs_bounce() is not necessary.

The sa1111, though, is a bit complicated. Until it's fully understood
and fixed, dma_needs_bounce() for sa1111 is kept if CONFIG_SA1111 is
enabled with no side effect (with the condition of machine_is_*)

Thanks for Mike Rapoport to fix one error in the original version of
the patch and get this tested.
Acked-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Not tested and enabled on MMP at this moment, and since the IRQ
is different from mach-pxa, I'd prefer to move the PMU device
back into mach-pxa/. Will introduce the PMU device to MMP once
it's enabled and tested.
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

pxa3xx cpu needs the irq type setup to be able to
wakeup from low power mode on IRQ_WAKEUPx events.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

Signed-off-by: NJonathan Cameron <jic23@cam.ac.uk>
Acked-by: NStefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>