In Spectrum-2, ACL regions that use 8 or 12 key blocks require several
consecutive hardware regions.

In order to allow defragmentation, the device stores a mapping from a
logical region ID to an hardware region ID, which is similar to the page
table that is used to translate virtual addresses to physical addresses.

Add the region association callback to the region create sequence and
implement it as a NOP in Spectrum which does not require it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Encode each flexible key block in the general block scheme according its
block index.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum the key (and mask) block layout is very straight forward and
every block is 16 bytes aligned.

However, in Spectrum-2 the blocks are not even byte aligned, which makes
it difficult to encode them using current method.

Instead, first encode each block and then encode the block in the
general blocks layout.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PGCR register configures general Policy-Engine settings.

Specifically, we are going to use it in order to set the default action
base pointer, which determines where the default action (when there is
no hit) is located for each region.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PERERP register configures the region eRPs. It can be used, for
example, to enable lookup in the C-TCAM in addition to the A-TCAM.

To be able to perform a lookup in the C-TCAM we need to "use" the eRP
table. This is done by marking the pointer as valid, but zeroing the eRP
table vector.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PERCR register configures the region parameters such as whether to
consult the bloom filter before performing a lookup using a specific
eRP.

For C-TCAM only usage we don't need to accurately set the master mask.
Instead, we can set all of its bits to make sure all the extracted keys
are actually used.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PERAR register is used to associate a hw region for region_id's.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2, activity cannot be find out by TCAM rule (PTCEv2 register),
but rather by associated action set. For that purpose, extend action ops
to allow query activity from PEFA register. Block activity is decided
according to activity of the first set.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2, the PEFA register is extend to report if the action set
was hit during processing of packets. Introduce this extension and
adjust the code around this accordingly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce key blocks for Spectrum-2 that contains the same elements used
already for Spectrum1. Along with that, introduce encoder stub.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2, no action set is stored directly in TCAM, all are located
in KVD linear. So ask core to treat the first set as dummy empty one,
to be just used for PTCEV2 purposes.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add dummy ops for now. The ops are going to be implemented later on.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In Spectrum-2, KVD linear indexes are hashed into KVD hash. Therefore it
is possible for multiple resource types to use same indexes. There are
multiple index spaces. Also, the index space is bigger than the actual
KVD hash area, which allows to have holes in the index space without any
penalization. The HW has to be told in case the index for particular
resource type is no longer used so it can be freed from KVD hash. IEDR
register is used for that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IEDR register is used for deleting entries from the entry tables.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simon Wunderlich says:

====================
This feature/cleanup patchset includes the following patches:

 - Don't call BATMAN_V experimental in Kconfig anymore, by Sven Eckelmann

 - Enable DAT by default at compile time, by Antonio Quartulli

 - Remove obsolete default n in Kconfig, by Sven Eckelmann

 - Fix checkpatch spelling errors, by Sven Eckelmann

 - Unify header guards style, by Sven Eckelmann

 - Consolidate batadv_purge_orig functions, by Sven Eckelmann

 - Replace type define with proper typedef, by Sven Eckelmann
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NHåkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit b6fb0df1 ("RDS/IB: Make ib_recv_refill return void") did
not change the comment accordingly.

Fixes: b6fb0df1 ("RDS/IB: Make ib_recv_refill return void")
Signed-off-by: NHåkon Bugge <haakon.bugge@oracle.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@oracle.ccom>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/dsa/rtl8366.c: In function ‘rtl8366_reset_vlan’:
drivers/net/dsa/rtl8366.c:234:25: warning: unused variable ‘vlan4k’ [-Wunused-variable]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Niklas Söderlund says:

====================
ravb: small sparse fixes

This are fixes that have bugged me whenever I run sparse to check my own
changes to the driver. It's based on the latest net-next tree and tested
on M3-N.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The wrong helper is used to swap the bytes when adding the lower bits of
the TX descriptors tag field in the shared ds_tagl variable. The
variable contains the DS[11:0] field and then the TAG[3:0] bits.

The mistake was highlighted by the sparse warning:

ravb_main.c:1622:31:    left side has type restricted __le16
ravb_main.c:1622:31:    right side has type unsigned short
ravb_main.c:1622:31: warning: invalid assignment: |=
ravb_main.c:1622:34: warning: cast to restricted __le16
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes sparse warning:

ravb_main.c:1257 ravb_get_strings() error: memcpy() '*ravb_gstrings_stats' too small (32 vs 960)
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inside a loop in ravb_get_ethtool_stats() a variable 'stats' is declared
resulting in the argument also named 'stats' to be shadowed. Fix this
warning by renaming the unused argument 'stats' to 'estats'.

This fixes the sparse warning:

ravb_main.c:1225:36: originally declared here
ravb_main.c:1233:41: warning: symbol 'stats' shadows an earlier one
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the Ethernet and Realtek switch device to the
D-Link DIR-685 Gemini-based device.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds a driver core for the Realtek SMI chips and a
subdriver for the RTL8366RB. I just added this chip simply
because it is all I can test.

The code is a massaged variant of the code that has been
sitting out-of-tree in OpenWRT for years in the absence of
a proper switch subsystem. This creates a DSA driver for it.
I have tried to credit the original authors wherever
possible.

The main changes I've done from the OpenWRT code:

- Added an IRQ chip inside the RTL8366RB switch to demux and
  handle the line state IRQs.

- Distributed the phy handling out to the PHY driver.

- Added some RTL8366RB code that was missing in the driver at
  the time, such as setting up "green ethernet" with a funny
  jam table and forcing MAC5 (the CPU port) into 1 GBit.

- Select jam table and add the default jam table from the
  vendor driver, also for ASIC "version 0" if need be.

- Do not store jam tables in the device tree, store them
  in the driver.

- Pick in the "initvals" jam tables from OpenWRT's driver
  and make those get selected per compatible for the
  whole system. It's apparently about electrical settings
  for this system and whatnot, not really configuration
  from device tree.

- Implemented LED control: beware of bugs because there are
  no LEDs on the device I am using!

We do not implement custom DSA tags. This is explained in
a comment in the driver as well: this "tagging protocol" is
not simply a few extra bytes tagged on to the ethernet
frame as DSA is used to. Instead, enabling the CPU tags
will make the switch start talking Realtek RRCP internally.
For example a simple ping will make this kind of packets
appear inside the switch:

0000   ff ff ff ff ff ff bc ae c5 6b a8 3d 88 99 a2 00
0010   08 06 00 01 08 00 06 04 00 01 bc ae c5 6b a8 3d
0020   a9 fe 01 01 00 00 00 00 00 00 a9 fe 01 02 00 00
0030   00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00

As you can see a custom "8899" tagged packet using the
protocol 0xa2. Norm RRCP appears to always have this
protocol set to 0x01 according to OpenRRCP. You can also
see that this is not a ping packet at all, instead the
switch is starting to talk network management issues
with the CPU port.

So for now custom "tagging" is disabled.

This was tested on the D-Link DIR-685 with initramfs and
OpenWRT userspaces and works fine on all the LAN ports
(lan0 .. lan3). The WAN port is yet not working.

Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Realtek SMI family is a set of DSA chips that provide
switching in routers. This binding just follows the pattern
set by other switches but with the introduction of an embedded
irqchip to demux and handle the interrupts fired by the single
line from the chip.

This interrupt construction is similar to how we handle
interrupt controllers inside PCI bridges etc.

Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RTL8366RB is an ASIC with five internal PHYs for
LAN0..LAN3 and WAN. The PHYs are spawn off the main
device so they can be handled in a distributed manner
by the Realtek PHY driver. All that is really needed
is the power save feature enablement and letting the
PHY driver core pick up the IRQ from the switch chip.

Cc: Antti Seppälä <a.seppala@gmail.com>
Cc: Roman Yeryomin <roman@advem.lv>
Cc: Colin Leitner <colin.leitner@googlemail.com>
Cc: Gabor Juhos <juhosg@openwrt.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The removed code would be called in two situations:
1. interface is brought up never or >10s after driver load
2. after close()

Case 1 we can handle cleaner by ensuring chip is powered down when
leaving probe(). open() callback will power up the chip.

In case 2 we call rtl_pll_power_down() twice currently, from the
close() callback and 10s later when entering runtime-suspend.
This is avoided by this patch.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Andrew Lunn says:

====================
HWMON support for SFP modules

This patchset adds HWMON support to SFP modules. The two patches add
some attributes for temperature and power sensors which are currently
missing from the hwmon core. The third patch adds a helper for
filtering out characters in hwmon names which are invalid. The last
patch then extends the core SFP code to export the sensors found in
SFP modules.

This code has been tested with two SFP modules:

module OEM SFP-7000-85 rev 11.0 sn M1512220075 dc 160221
module FINISAR CORP. FTLF8524E2GNL rev A sn PW40MNN dc 160725

The anonymous module uses external calibration, while the FINISAR uses
internal calibration. Thus both code paths have been tested.

Due to the cross subsystem nature of these patches, as discussed with
the RFC, it is hoped Guenter Roeck will ACK the patches, and then Dave
Miller will merge them all via net-next.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SFP modules can contain a number of sensors. The EEPROM also contains
recommended alarm and critical values for each sensor, and indications
of if these have been exceeded. Export this information via
HWMON. Currently temperature, VCC, bias current, transmit power, and
possibly receiver power is supported.

The sensors in the modules can either return calibrate or uncalibrated
values. Uncalibrated values need to be manipulated, using coefficients
provided in the SFP EEPROM. Uncalibrated receive power values require
floating point maths in order to calibrate them. Performing this in
the kernel is hard. So if the SFP module indicates it uses
uncalibrated values, RX power is not made available.

With this hwmon device, it is possible to view the sensor values using
lm-sensors programs:

in0:          +3.29 V  (crit min =  +2.90 V, min =  +3.00 V)
                       (max =  +3.60 V, crit max =  +3.70 V)
temp1:        +33.0°C  (low  =  -5.0°C, high = +80.0°C)
                       (crit low = -10.0°C, crit = +85.0°C)
power1:      1000.00 nW (max = 794.00 uW, min =  50.00 uW)  ALARM (LCRIT)
                       (lcrit =  40.00 uW, crit = 1000.00 uW)
curr1:        +0.00 A  (crit min =  +0.00 A, min =  +0.00 A)  ALARM (LCRIT, MIN)
                       (max =  +0.01 A, crit max =  +0.01 A)

The scaling sensors performs on the bias current is not particularly
good. The raw values are more useful:

curr1:
  curr1_input: 0.000
  curr1_min: 0.002
  curr1_max: 0.010
  curr1_lcrit: 0.000
  curr1_crit: 0.011
  curr1_min_alarm: 1.000
  curr1_max_alarm: 0.000
  curr1_lcrit_alarm: 1.000
  curr1_crit_alarm: 0.000

In order to keep the I2C overhead to a minimum, the constant values,
such as limits and calibration coefficients are read once at module
insertion time. Thus only reading *_input and *_alarm properties
requires i2c read operations.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

HWMON device names are not allowed to contain "-* \t\n". Add a helper
which will return true if passed an invalid character. It can be used
to massage a string into a hwmon compatible name by replacing invalid
characters with '_'.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some sensors support reporting minimal and lower critical power, as
well as alarms when these thresholds are reached. Add support for
these attributes to the hwmon core.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The enum hwmon_temp_lcrit_alarm exists, but the BIT definition is
missing.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Heiner Kallweit says:

====================
r8169: add phylib support

Now that all the basic refactoring has been done we can add phylib
support. This patch series was successfully tested on:
RTL8168h
RTL8168evl
RTL8169sb

Changes in v2:
- return error in mdio ops if phyaddr > 0
- advertise pause modes
- added reviewed-by for several patches

Changes in v3:
- return ENODEV for unused phy addresses in mdio ops
- remove unneeded PHY suspend in patch 2
- use recently added phy_speed_down and phy_speed_up in patch 7
- other minor changes based on review comments
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of accessing the PHYstatus register we can use the information
phylib stores in the phy_device structure.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The only remaining usage of the struct mii_if_info member is to store the
information whether the chip is GMII-capable. So we can replace it with
a simple flag.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can remove rtl8169_set_speed_xmii() now that phylib handles all this.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use new phylib functions phy_speed_down() and phy_speed_up().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to using phy_mii_ioctl().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch to using phy_ethtool_nway_reset().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use phy_ethtool_(g|s)et_link_ksettings() for the respective ethtool_ops
callbacks.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>