The logic responsible for processing the event is
no different across different firmware binaries.
The difference that needs to be dealt with is the
ABI of data structures.

The intermediate structure uses __le32 to avoid
extra memory allocations to byteswap
variable-length substructures (i.e. host mem
chunks).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it more readable and fixes checkpatch warnings:

drivers/net/wireless/ath/ath10k/debug.c:593: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:594: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:595: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:596: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:597: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:599: WARNING: quoted string split across lines
drivers/net/wireless/ath/ath10k/debug.c:600: WARNING: quoted string split across lines
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Fixes checkpatch warnings:

WARNING: else is not generally useful after a break or return
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CHECK: Alignment should match open parenthesis
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The function may return an -ENODEV if debugfs is
disabled in kernel. This should originally be
guarded by ath10k's Kconfig but it still makes
sense to check for the non-NULL errno return
value.
Reported-by: NMatteo Croce <matteo@openwrt.org>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

10.1 firmware does not have an official way to
cause assert on purpose, but it can be done with
carefully crafted WMI command.  This is a different
kind of crash from the 'hard' crash, which is
a bad memory dereference.

Different crashes decode in different manners, so
this will help the crash-report testing as well as
offer better ways to test firmware failure and
recovery.

kvalo: move the wmi command creation to debug.c, modify
the info print
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add testmode interface for starting and using UTF firmware which is used to run
factory tests. This is implemented by adding new state ATH10K_STATE_UTF and user
space can enable this state with ATH10K_TM_CMD_UTF_START command. To go back to
normal mode user space can send ATH10K_TM_CMD_UTF_STOP.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

On 32bit systems the bitmap was too small and it
was overwritten partially by the stat completion
structure. This was visible with 10.2 firmware
only due to it using a few of the last service
ids.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The fw_crash_data was allocated too late. Upon
early firmware crash, before registering to
mac80211, it was possible to crash the whole
system:

 ath10k_pci 0000:00:05.0: device has crashed during init
 BUG: unable to handle kernel NULL pointer dereference at           (null)
 IP: [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
 PGD 0
 Oops: 0002 [#1] SMP
 Modules linked in: ath10k_pci(O) ath10k_core(O) ath [last unloaded: ath]
 CPU: 3 PID: 29 Comm: kworker/u8:1 Tainted: G           O   3.17.0-rc2-wl-ath+ #447
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
 Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
 task: ffff88001eb01ad0 ti: ffff88001eb60000 task.ti: ffff88001eb60000
 RIP: 0010:[<ffffffffa0058005>]  [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
 RSP: 0018:ffff88001eb63ce8  EFLAGS: 00010246
 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000
 RDX: 0000000000000000 RSI: ffffc90001a09030 RDI: 0000000000000001
 RBP: ffff88001eb63cf0 R08: 0000000000000000 R09: ffff8800000bb200
 R10: 00000000000001e2 R11: ffff88001eb638de R12: ffff88001d7459a0
 R13: ffff88001d746ab0 R14: 00000000fffe14d4 R15: ffff88001d747c60
 FS:  0000000000000000(0000) GS:ffff88001fd80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000000 CR3: 000000001df34000 CR4: 00000000000006e0
 Stack:
  ffff88001d7459a0 ffff88001eb63d58 ffffffffa0083bbe ffff880000000010
  ffff88001eb63d68 ffff88001eb63d18 0000000000000002 0000000000059010
  ffffffffa0086fef 00000000deadbeef ffff88001d747a28 ffff88001d7459a0
 Call Trace:
  [<ffffffffa0083bbe>] ath10k_pci_fw_crashed_dump+0x2e/0xd0 [ath10k_pci]
  [<ffffffffa0085410>] __ath10k_pci_hif_power_up+0x5f0/0x700 [ath10k_pci]
  [<ffffffffa0085550>] ath10k_pci_hif_power_up+0x30/0xe0 [ath10k_pci]
  [<ffffffffa005bc7b>] ath10k_core_register_work+0x2b/0x520 [ath10k_core]
  [<ffffffff810689cc>] process_one_work+0x18c/0x3f0
  [<ffffffff81069011>] worker_thread+0x121/0x4a0
  [<ffffffff81068ef0>] ? rescuer_thread+0x2c0/0x2c0
  [<ffffffff8106daf2>] kthread+0xd2/0xf0
  [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170
  [<ffffffff81857cfc>] ret_from_fork+0x7c/0xb0
  [<ffffffff8106da20>] ? kthread_create_on_node+0x170/0x170
 Code: 8b 40 38 48 c7 80 00 01 00 00 00 00 00 00 5b 5d c3 0f 1f 44 00 00 0f 1f 44 00 00 55 48 89 e5 53 48 8b 9f 90 1d 00 00 48 8d 7b 01 <c6> 03 01 e8 e3 ec 2b e1 48 8d 7b 18 e8 6a 4f 05 e1 48 89 d8 5b
 RIP  [<ffffffffa0058005>] ath10k_debug_get_new_fw_crash_data+0x15/0x30 [ath10k_core]
  RSP <ffff88001eb63ce8>
 CR2: 0000000000000000
 ---[ end trace 5d0ed15b050bcc1f ]---
 Kernel panic - not syncing: Fatal exception in interrupt
 Kernel Offset: 0x0 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffff9fffffff)
 ---[ end Kernel panic - not syncing: Fatal exception in interrupt

To prevent that split debug functions and allocate
fw_crash_data earlier.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it easier to log and debug via tracing
with more than 1 ath10k device on a system.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes users forget to include important info like firmware version,
so better to print all the info.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Store the firmware registers and other relevant data to a firmware crash dump
file and provide it to user-space via debugfs. Should help with figuring out
why the firmware crashed.

kvalo: remove dbglog support, rework and refactor the code to avoid ifdefs and
otherwise simplify it as well
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The 10.x and main firmware branches have
conflicting WMI service bitmap definitions.

This also fixes WMI services parsing on big-endian
hosts and changes debugfs output to be more human
friendly.

kvalo: remove braces and the last semicolon from SVCSTR()
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Different firmware may support different numbers of
vdevs.  Use value that is always out of range for all
firmware.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Allow to setup maximum subframes for AMSDU and AMPDU aggregation
via debugfs htt_max_amsdu_ampdu file.

Eg.
echo "2 64" > htt_max_amsdu_ampdu
will setup maximum amsdu subframes equal 2 and
maximum ampdu subframes equal to 64.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As pointed out by Michal Kazior, add extra pdev stats
for 10.1 firmware.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

FW stats does provide the Rx rate information. Add this.
Tested with firmware 10x firmware.

Increase buffer size so more peers can be shown.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Using the macro to convert the MAC address from WMI word
format to char array has lead to the wrong peer mac
address printed out while retrieving the peer stats from
FW. Fix this.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Reviewed-By: NMichał Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Command WMI_FORCE_FW_HANG_CMDID is not supported in firmware 10.1.
In order to have firmware crash simulation functionality also
in firmware 10.1 driver can force firmware crash by performing not allowed
operation. Driver can deliberately crash firmware when setting vdev param for
vdev id out of range.  This patch introduces two keywords to simulate_fw_crash:

'soft' which will cause firmware crash that is recoverable
       by warm firmware reset but supported only in main firmware.
'hard' which will cause firmware crash recoverable by cold
       firmware reset, this option works for both firmwares.

Commands to trigger firmware soft/hard crash:

echo 'soft' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash
echo 'hard' > /sys/kernel/debug/ieee80211/phyX/ath10k/simulate_fw_crash

kvalo: remove '\n' before checking the command and simplify how buf is null
terminated
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware dbglogs can be now enabled through fw_dbglog file. To enable all
possible log messages run:

echo 0xffffffff > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog

And to put back firmare defaults use 0x0:

echo 0x0 > /sys/kernel/debug/ieee80211/phy0/ath10k/fw_dbglog
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Sometimes for DFS testing is required to stay on current channel even after
radar detected. This patch allows to enable/disable radar detected event to be
passed to mac80211.

By default radar detected event in not blocked.

To block it:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events

To unblock again:
echo 0 > /sys/kernel/debug/ieee80211/phyX/ath10k/dfs_block_radar_events

Inform about blocking radar detected event even when logs are disabled
for throughput/performance reasons.
Signed-off-by: NMarek Puzyniak <marek.puzyniak@tieto.com>
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Handle phyerr, dfs event, radar_report and fft_report.
Add also debugfs dfs_simulate_radar and dfs_stats files.
Use ath dfs pattern detector.
Signed-off-by: NJanusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_debug_start() was not called with conf_mutex, fix that. Also there was a
deadlock in ath10k_debug_stop(), rename it to ath10k_debug_destroy() and call
it only when the device is destroyed.
Reported-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed for the HTT stats implementation.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

So that's it's possible to query chip id from ath10k anytime.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

ath10k_debug_read_target_stats is properly
protected by data_lock (spinlock). Remove
the unwanted mutex_unlock(&ar->conf_mutex)

[ BUG: bad unlock balance detected! ]
-------------------------------------
kworker/u4:0/12459 is trying to release lock
(&ar->conf_mutex) at:
[<c16a170d>] mutex_unlock+0xd/0x10
but there are no more locks to release!

 Call Trace:
  [<c16a170d>] ? mutex_unlock+0xd/0x10
  [<c10b697d>] __lock_release+0x4d/0xe0
  [<f88ca0fc>] ? ath10k_debug_read_target_stats+0xac/0x290

  [<c16a170d>] ? mutex_unlock+0xd/0x10
  [<c10b6a5b>] lock_release+0x4b/0x150
  [<c16a1580>] __mutex_unlock_slowpath+0x70/0x150
  [<f88ca0fc>] ? ath10k_debug_read_target_stats+0xac/0x290

  [<c10b456b>] ? trace_hardirqs_on+0xb/0x10
  [<c16a170d>] mutex_unlock+0xd/0x10
  [<f88ca107>] ath10k_debug_read_target_stats+0xb7/0x290

  [<f88d337a>] ath10k_wmi_event_process+0x3fa/0x6e0

  [<c10b456b>] ? trace_hardirqs_on+0xb/0x10
  [<f88d36e1>] ath10k_wmi_event_work+0x21/0x40
               [ath10k_core]
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This can be useful for testing. To perform a
forced firmware crash write 'crash' to
'simulate_fw_crash' debugfs file. E.g.

  echo crash > /sys/kernel/debug/ieee80211/phy1/ath10k/simulate_fw_crash
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

If the device is not running then there may be no
FW at all to send the query to. If the FW is
already there it might still trigger a crash if
the command is sent before the device is fully
initialized.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.

The wiki page for the driver is:

http://wireless.kernel.org/en/users/Drivers/ath10k

The driver has had many authors, they are listed here alphabetically:

Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>