mpt2sas: Get IOC_FACTS information using handshake protocol only after HBA card gets into READY or Operational state.

Driver initialization fails if driver tries to send IOC facts request message when the IOC is in reset or in a fault state.

This patch will make sure that
 1.Driver to send IOC facts request message only if HBA is in operational or ready state.
 2.If IOC is in fault state, a diagnostic reset would be issued.
 3.If IOC is in reset state then driver will wait for 10 seconds to exit out of reset state.
   If the HBA continues to be in reset state, then the HBA wouldn't be claimed by the driver.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Up to now, Driver allocates a single contiguous block of memory
pool for all reply queues and passes down a single address in the
ReplyDescriptorPostQueueAddress field of the IOC Init Request
Message to the firmware.

When firmware receives this address, it will program each of the
Reply Descriptor Post Queue registers, as each reply queue has its
own register. Thus the firmware, starting from a base address it
determines the starting address of the subsequent reply queues
through some simple arithmetic calculations.

The size of this contiguous block of memory pool is directly proportional
to number of MSI-X vectors and the HBA queue depth. For example higher
MSIX vectors requires larger contiguous block of memory pool.

But some of the OS kernels are unable to allocate this larger
contiguous block of memory pool.

So, the proposal is to allocate memory independently for each
Reply Queue and pass down all of the addresses to the firmware.
Then the firmware will just take each address and program the value
into the correct register.

When HBAs with older firmware(i.e. without RDPQ capability) is used
with this new driver then the max_msix_vectors value would be set
to 8 by default.

Change_set in v1:

1. Declared _base_get_ioc_facts() function at the beginning of the mpt2sas_base.c
file instead of moving all these functions before mpt2sas_base_map_resources() function
        a. _base_wait_for_doorbell_int()
        b. _base_wait_for_doorbell_ack()
        c. _base_wait_for_doorbell_not_used()
        d. _base_handshake_req_reply_wait()
        e. _base_get_ioc_facts()

2. Initially set the consistent DMA mask to 32 bit and then change it to 64 bit mask
after allocating RDPQ pools by calling the function _base_change_consistent_dma_mask.
This is to ensure that all the upper 32 bits of RDPQ entries's base address to be same.

3. Reduced the redundancy between the RDPQ and non-RDPQ support in these following functions
        a. _base_release_memory_pools()
        b. _base_allocate_memory_pools()
        c. _base_send_ioc_init()
        d. _base_make_ioc_operational()
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

A type casting error caused the max volume LBA to be truncated from 64
to 32 bits. The virtual LBA would also get truncated to 32 bits in the
case of a 16-byte READ/WRITE command.

Rewrite entire function to get rid of code duplication and type casts.
Use get/put_unaligned wrappers to extract and replace the LBA field in
the MPI request CDB.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Tested-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Bump mpt2sas driver version to 17.100.00.00
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Added code to send a SEP message that turns off the Predictive
Failure LED when a drive is removed (if Predictive Failure LED was turned on).

Added a new flag 'pfa_led_on' per device that tracks the status of Predictive
Failure LED. When the drive is removed, this flag is checked and
sends the SEP message to turn off the respective Predictive Failure LED.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Copyright in driver sources is updated for year the 2014.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Below is the change set in MPI2 Rev Y specification and in 2.00.17 header files
1) Added SCSIStatusQualifier to SCSI IO Error Reply message.
2) Added ATA Security Freeze Lock to IO Unit Page 1 Flags field.

Below is the change set in MPI2 Rev Z specification and in 2.00.19 header files
1) Added reserved fields to IO Unit Page 7 for future use.
2) Added optional functionality to IOCInit Request so that
   the host may specify a separate base address for each
   Reply Descriptor Post Queue. IOC support for this is
   indicated using a new IOCCapabilities bit in the IOCFacts Reply.
3) Added Toolbox Console Text Display Tool
   The host uses the Console Text Display Tool to send a string to
   IOC's Console using different console types (eg: UART serial terminal or Ethernet terminal).

The copyright in the mpi files is updated for year 2014
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Added driver module parameter max_msix_vectors. Using this
module parameter the maximum number of MSI-X vectors could be set.

The number of MSI-X vectors used would be the minimum of MSI-X vectors
supported by the HBA, the number of CPU cores and the value set to
max_msix_vectors module parameters.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NTej Parkash <tej.parkash@qlogic.com>
Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

This patch is based on a problem and solution from Maurizio Lombardi
where bnx2fc isn't consistent in which device struct we using for DMA
map and unmap operations.  Make them consistent by using dma_sg_unmap
in bnx2fc_unmap_sg_list like bnx2fc_map_sg.
Reviewed-by: NEddie Wai <eddie.wai@broadcom.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Update lpfc version to driver version 10.4.8000.0
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix for handling unmapped ndlp in target reset handler
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fixed Low priority issues from lpfc given by fortify source code scan.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fixed High priority issues from lpfc given by fortify source code scan.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix crash from page fault caused by use after rport delete.
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix locking issues with abort data paths
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix race between LOGO/PLOGI handling causing NULL pointer
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix IP Reset processing - wait for RDY before proceeding
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix quarantined XRI recovery qualifier state in link bounce
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Fix discovery timeout during nameserver login
Signed-off-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NDick Kennedy <dick.kennedy@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

In prandom we have already reseeding mechanisms that trigger
periodically from a much better entropy source than just
feeding in jiffies through lpfc_mbx_cmpl_fcf_scan_read_fcf_rec()
[what a function name 8-)]. Therefore, just remove this.
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

To be future-proof and for better readability the time comparisons
are modified to use time_after() instead of plain, error-prone math.
Signed-off-by: NManuel Schölling <manuel.schoelling@gmx.de>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: NJoe Perches <joe@perches.com>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

[PATCH 26/55] scsi: Mark function as static in lpfc/lpfc_bsg.c

Mark function as static in lpfc/lpfc_bsg.c because it is not used
outside this file.

This eliminates the following warning in lpfc/lpfc_bsg.c:
drivers/scsi/lpfc/lpfc_bsg.c:3348:1: warning: no previous prototype for ‘lpfc_bsg_issue_mbox_cmpl’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Mark functions as static in lpfc/lpfc_scsi.c because they are not used
outside this file.

This eliminates the following warnings in lpfc/lpfc_scsi.c:
drivers/scsi/lpfc/lpfc_scsi.c:299:1: warning: no previous prototype for ‘lpfc_change_queue_depth’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:795:1: warning: no previous prototype for ‘lpfc_sli4_post_scsi_sgl_list’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3019:1: warning: no previous prototype for ‘lpfc_bg_crc’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3035:1: warning: no previous prototype for ‘lpfc_bg_csum’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_scsi.c:3048:1: warning: no previous prototype for ‘lpfc_calc_bg_err’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Mark functions as static in lpfc/lpfc_init.c because they are not used
outside this file.

This eliminates the following warning in lpfc/lpfc_init.c:
drivers/scsi/lpfc/lpfc_init.c:652:1: warning: no previous prototype for ‘lpfc_hba_init_link’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_init.c:753:1: warning: no previous prototype for ‘lpfc_hba_down_link’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_init.c:3434:1: warning: no previous prototype for ‘lpfc_sli4_fcf_redisc_wait_tmo’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Mark functions as static in lpfc/lpfc_hbadisc.c because they are not
used outside this file.

This eliminates the following warnings in lpfc/lpfc_hbadisc.c:
drivers/scsi/lpfc/lpfc_hbadisc.c:2047:5: warning: no previous prototype for ‘lpfc_sli4_fcf_pri_list_add’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_hbadisc.c:2681:1: warning: no previous prototype for ‘lpfc_init_vfi_cmpl’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_hbadisc.c:4432:1: warning: no previous prototype for ‘lpfc_nlp_logo_unreg’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

[PATCH 22/55] scsi: Mark functions as static in lpfc/lpfc_sli.c

Mark functions as static in lpfc/lpfc_sli.c because they are not used
outside this file.

This eliminates the following warnings in lpfc/lpfc_sli.c:
drivers/scsi/lpfc/lpfc_sli.c:13867:1: warning: no previous prototype for ‘lpfc_sli4_alloc_xri’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:13897:1: warning: no previous prototype for ‘__lpfc_sli4_free_xri’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:14317:1: warning: no previous prototype for ‘lpfc_update_rcv_time_stamp’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:14786:1: warning: no previous prototype for ‘lpfc_sli4_handle_unsol_abort’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:15331:1: warning: no previous prototype for ‘__lpfc_sli4_free_rpi’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:15769:1: warning: no previous prototype for ‘lpfc_check_next_fcf_pri_level’ [-Wmissing-prototypes]
drivers/scsi/lpfc/lpfc_sli.c:16000:1: warning: no previous prototype for ‘lpfc_mbx_cmpl_redisc_fcf_table’ [-Wmissing-prototypes]
Signed-off-by: NRashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: NJosh Triplett <josh@joshtriplett.org>
Reviewed-by: NJames Smart <james.smart@emulex.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

1) Assgning FIP_ALL_FCF_MACS to fcoe_all_fcfs allows VLAN request to be sent
to correct Mac address for VLAN Discovery otherwise VLAN request will be
sent to invalid address hence FLOGI never happens.

2) Simplify the copy_and_format_trace_data code and log the correct Link event
for fnic control path tracing in case of link status UP->UP.

3) Increment Fnic driver version
Signed-off-by: NHiral Shah <hishah@cisco.com>
Signed-off-by: NSesidhar Baddela <sebaddel@cisco.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

The PCI register read checking introduced in commit fe1b806f
("qla2xxx: Disable adapter when we encounter a PCI disconnect") is
active during driver probe. Hold off scheduling any board removal until
the driver probe has completed. This ensures that the the board_disable
work structure is initialized and more importantly, avoids racing
qla2x00_probe_one.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Introduce mutual exclusion between the qla2xxx_remove_one PCI driver
callback and qla2x00_disable_board_on_pci_error, which is scheduled as
board_disable work by qla2x00_check_reg{32,16}_for_disconnect:

* Leave the driver-specific data attached to the underlying PCI device
intact in qla2x00_disable_board_on_pci_error, so that qla2x00_remove_one
has enough breadcrumbs to determine that any board_disable work has been
completed.

* In qla2xxx_remove_one, set a bit to prevent any subsequent
board_disable work from scheduling, then cancel and wait until pending
work has completed.

* Reuse the PCI device enable count check in qla2x00_remove_one to
determine if board_disable has occured. The original purpose of this
check was unnecessary since the driver remove function wasn't called
when the probe fails.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There are various callers of qla2x00_check_reg{32,16}_for_disconnect
that may schedule board removal on PCI-disconnect. Test-and-set a
dedicated flag before scheduling board_disable so it is invoked only
once.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add an uint16_t variant of qla2x00_check_reg_for_disconnect and use
these routines to check and schedule a PCI-disconnected board from a
centralized place.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Take advantage of commit fe1b806f ("qla2xxx: Refactor shutdown code
so some functionality can be reused") to remove an inlined copy of
qla2x00_clear_drv_active in the driver's probe hardware error path.
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Once calling scsi_host_put, be careful to not access qla_hw_data through
the Scsi_Host private data (ie, scsi_qla_host base_vha).

Fixes: fe1b806f ("qla2xxx: Refactor shutdown code so some functionality can be reused")
Cc: stable@vger.kernel.org # 3.14, 3.15, 3.16
Signed-off-by: NJoe Lawrence <joe.lawrence@stratus.com>
Acked-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

As result of deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range()  or pci_enable_msi_exact()
and pci_enable_msix_range() or pci_enable_msix_exact()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

There is no need to call pci_disable_msix() in case
the previous call to pci_enable_msix() failed
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>