This is another prepatory patch to be able to handle aggregated RX
packets.

In order to avoid adding a prototype, this also moves the
rtl8723bu_handle_c2h() function.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This needs to be handled locally in the parse_rx_desc() function in
order to be able to handle aggregated packets in the future.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Changed the configuration to support 64bit instead of 32bit
this in order to offload the driver from handling a wraparound.
Signed-off-by: NYaniv Machani <yanivma@ti.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes below NULL pointer dereference observed in suspend
stress test. When scan is cancelled during system suspend, we may end
up aceesing "priv->scan_request" in corner case.

[ 3035.304682] BUG: KASAN: null-ptr-deref on address 0000000000000008
[ 3035.304704] Read of size 4 by task ksdioirqd/mmc2/1183
[ 3035.304744] CPU: 0 PID: 1183 Comm: ksdioirqd/mmc2 Tainted: G        W      3.18.0 #1169
[ 3035.304772] Call trace:
[ 3035.304825] [<ffffffc00020a520>] dump_backtrace+0x0/0x190
[ 3035.304864] [<ffffffc00020a6cc>] show_stack+0x1c/0x28
[ 3035.304901] [<ffffffc000b36db8>] dump_stack+0xa0/0xf8
[ 3035.304940] [<ffffffc00039c494>] kasan_report+0x120/0x4fc
[ 3035.304975] [<ffffffc00039b6b4>] __asan_load4+0x20/0x80
[ 3035.305546] [<ffffffbffc1f5aec>] mwifiex_check_next_scan_command+0x1a4/0x588 [mwifiex]
[ 3035.306091] [<ffffffbffc1f7aec>] mwifiex_handle_event_ext_scan_report+0x304/0x370 [mwifiex]
[ 3035.306735] [<ffffffbffc206bb8>] mwifiex_process_sta_event+0x6c0/0xf10 [mwifiex]
[ 3035.307200] [<ffffffbffc1e609c>] mwifiex_process_event+0x2f4/0x358 [mwifiex]
[ 3035.307612] [<ffffffbffc1e25c8>] mwifiex_main_process+0x3cc/0x80c [mwifiex]
[ 3035.307737] [<ffffffbffc2523a0>] mwifiex_sdio_interrupt+0x198/0x1c0 [mwifiex_sdio]
[ 3035.307785] [<ffffffc0008d9250>] process_sdio_pending_irqs+0x15c/0x1d4
[ 3035.307826] [<ffffffc0008d93f0>] sdio_irq_thread+0xd8/0x288
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The flag should be cleaned along with other scan operation variables.
This was missing at some places.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We will derive sta_priv at the beginning of suspend handler.
This will be useful for next patch in this series.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This debugging macro can expand to a lot of code.
Make it a function to reduce code size.

(x86-64 defconfig w/ all rtlwifi drivers and allyesconfig)
$ size drivers/net/wireless/realtek/rtlwifi/built-in.o*
   text	   data	    bss	    dec	    hex	filename
 900083	 200499	   1907	1102489	 10d299	drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.new
1113597	 200499	   1907	1316003	 1414a3	drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.old
1746879	 453503	   8512	2208894	 21b47e	drivers/net/wireless/realtek/rtlwifi/built-in.o.new
2051965	 503311	   8512	2563788	 271ecc	drivers/net/wireless/realtek/rtlwifi/built-in.o.old
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

USB urbs will return with a status != 0 when rmmod'ing the driver. No
need to fill the log with messages from rtl8xxxu_int_complete()
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

reg_eac and reg_ecc are only used if candidate is bigger than 0, and in
that case new values will be given to them. Removing the unused
assignments.
Signed-off-by: NLuis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

* work on DQA continued
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes

All transports has this structure. By moving it to be
shared, we can get rid of casting to the specific transport
in probe and remove.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Centralize the logging of SCD status. The motivation is
that for a000 devices we will have new SCD HW, but this
code was duplicate anyway, so it is a proper cleanup.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for the v4 version of the TX power command.  Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.

This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Update the firmware load flow for TFH hardware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the write_prph_64 of pcie to be transport agnostic.
Add direct write as well, as it is needed for a000 HW.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the scratch buffer is set to 16 bytes and indicates
the size of the bi-directional DMA.
However, next HW generation will perform additional offloading,
and will write the result in the key location of the TX command,
so the size of the bi-directional consistent memory should grow
accordingly - increase it to 40.
Generalize the code to get rid of now irrelevant scratch references.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In MQ environment and new architecture in early stages
we may encounter DMA issues. Track RXB status and bail
out in case we receive index to an RXB that was not
mapped and handed over to HW.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:

CPU0					CPU1
iwl_pcie_load_given_ucode
	...
	iwl_pcie_load_firmware_chunk
		wait_for_interrupt
					<interrupt>
					ISR handles CSR_INT_BIT_FH_TX
					ISR wakes up the thread on CPU0
	/* enable all the interrupts
	 * to get the ALIVE interrupt
	 */
	iwl_enable_interrupts
					ISR re-enables CSR_INT_BIT_FH_TX only
	/* start the firmware */
	iwl_write32(trans, CSR_RESET, 0);

BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.

In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).

All the credit for the analysis goes to Kirtika who did the
actual debugging work.

Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005f ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.

In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.

To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to be able to properly record SKBs that didn't come through
mac80211, don't rely on the IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag
but instead check for ETH_P_PAE directly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 10b2b201 ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add some prints to track BAID assignment.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.

Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.

Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support TDLS when working in DQA mode.

This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In cases of hardware or DMA error, the vid read from
a zeroed location will be 0, and we will access the rxb
at index 0 in the global table, while it may be NULL or
owned by hardware.
Invalidate vid 0 in order to detect the situation and
bail out.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This led to a DMA splat.

Fixes: a6c4fb44 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This struct member is never set, so remove it.

Since this is the last thing that needs mac80211.h, also change
the includes to no longer use mac80211.h
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The value for Channel 14 was wrong. Fix it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Those comments were wrong, fix them.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.

In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 38c0f334 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.

In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure.  If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).

Fixes: commit f4a3ee49 ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.

Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005f ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>