- 18 5月, 2018 6 次提交
-
-
由 Nicholas Piggin 提交于
Signed-off-by: NNicholas Piggin <npiggin@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Nicholas Piggin 提交于
tlbies to an LPAR do not have to be serialised since POWER4/PPC970, after which the MMU_FTR_LOCKLESS_TLBIE feature was introduced to avoid tlbie locking. Since commit c17b98cf ("KVM: PPC: Book3S HV: Remove code for PPC970 processors"), KVM no longer supports processors that do not have this feature, so the tlbie locking can be removed completely. A sanity check for the feature is put in kvmppc_mmu_hv_init. Testing was done on a POWER9 system in HPT mode, with a -smp 32 guest in HPT mode. 32 instances of the powerpc fork benchmark from selftests were run with --fork, and the results measured. Without this patch, total throughput was about 13.5K/sec, and this is the top of the host profile: 74.52% [k] do_tlbies 2.95% [k] kvmppc_book3s_hv_page_fault 1.80% [k] calc_checksum 1.80% [k] kvmppc_vcpu_run_hv 1.49% [k] kvmppc_run_core After this patch, throughput was about 51K/sec, with this profile: 21.28% [k] do_tlbies 5.26% [k] kvmppc_run_core 4.88% [k] kvmppc_book3s_hv_page_fault 3.30% [k] _raw_spin_lock_irqsave 3.25% [k] gup_pgd_range Signed-off-by: NNicholas Piggin <npiggin@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Simon Guo 提交于
When KVM emulates VMX store, it will invoke kvmppc_get_vmx_data() to retrieve VMX reg val. kvmppc_get_vmx_data() will check mmio_host_swabbed to decide which double word of vr[] to be used. But the mmio_host_swabbed can be uninitialized during VMX store procedure: kvmppc_emulate_loadstore \- kvmppc_handle_store128_by2x64 \- kvmppc_get_vmx_data So vcpu->arch.mmio_host_swabbed is not meant to be used at all for emulation of store instructions, and this patch makes that true for VMX stores. This patch also initializes mmio_host_swabbed to avoid possible future problems. Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Simon Guo 提交于
This patch moves nip/ctr/lr/xer registers from scattered places in kvm_vcpu_arch to pt_regs structure. cr register is "unsigned long" in pt_regs and u32 in vcpu->arch. It will need more consideration and may move in later patches. Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Simon Guo 提交于
Current regs are scattered at kvm_vcpu_arch structure and it will be more neat to organize them into pt_regs structure. Also it will enable reimplementation of MMIO emulation code with analyse_instr() later. Signed-off-by: NSimon Guo <wei.guo.simon@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
This merges in the ppc-kvm topic branch of the powerpc repository to get some changes on which future patches will depend, in particular the definitions of various new TLB flushing functions. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
- 17 5月, 2018 14 次提交
-
-
由 Souptick Joarder 提交于
Use new return type vm_fault_t for fault handler in struct vm_operations_struct. For now, this is just documenting that the function returns a VM_FAULT value rather than an errno. Once all instances are converted, vm_fault_t will become a distinct type. commit 1c8f4220 ("mm: change return type to vm_fault_t") Signed-off-by: NSouptick Joarder <jrdr.linux@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Alexey Kardashevskiy 提交于
Although it does not seem possible to break the host by passing bad parameters when creating a TCE table in KVM, it is still better to get an early clear indication of that than debugging weird effect this might bring. This adds some sanity checks that the page size is 4KB..16GB as this is what the actual LoPAPR supports and that the window actually fits 64bit space. Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru> Acked-by: NBalbir Singh <bsingharora@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Alexey Kardashevskiy 提交于
At the moment we only support in the host the IOMMU page sizes which the guest is aware of, which is 4KB/64KB/16MB. However P9 does not support 16MB IOMMU pages, 2MB and 1GB pages are supported instead. We can still emulate bigger guest pages (for example 16MB) with smaller host pages (4KB/64KB/2MB). This allows the physical IOMMU pages to use a page size smaller or equal than the guest visible IOMMU page size. Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Alexey Kardashevskiy 提交于
The other TCE handlers use page shift from the guest visible TCE table (described by kvmppc_spapr_tce_iommu_table) so let's make H_STUFF_TCE handlers do the same thing. This should cause no behavioral change now but soon we will allow the iommu_table::it_page_shift being different from from the emulated table page size so this will play a role. Signed-off-by: NAlexey Kardashevskiy <aik@ozlabs.ru> Reviewed-by: NDavid Gibson <david@gibson.dropbear.id.au> Acked-by: NBalbir Singh <bsingharora@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
We now have interrupts hard-disabled when coming back from kvmppc_hv_entry_trampoline, so this changes the comment to reflect that. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
Although Linux doesn't use PURR and SPURR ((Scaled) Processor Utilization of Resources Register), other OSes depend on them. On POWER8 they count at a rate depending on whether the VCPU is idle or running, the activity of the VCPU, and the value in the RWMR (Region-Weighting Mode Register). Hardware expects the hypervisor to update the RWMR when a core is dispatched to reflect the number of online VCPUs in the vcore. This adds code to maintain a count in the vcore struct indicating how many VCPUs are online. In kvmppc_run_core we use that count to set the RWMR register on POWER8. If the core is split because of a static or dynamic micro-threading mode, we use the value for 8 threads. The RWMR value is not relevant when the host is executing because Linux does not use the PURR or SPURR register, so we don't bother saving and restoring the host value. For the sake of old userspace which does not set the KVM_REG_PPC_ONLINE register, we set online to 1 if it was 0 at the time of a KVM_RUN ioctl. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
This adds a new KVM_REG_PPC_ONLINE register which userspace can set to 0 or 1 via the GET/SET_ONE_REG interface to indicate whether it considers the VCPU to be offline (0), that is, not currently running, or online (1). This will be used in a later patch to configure the register which controls PURR and SPURR accumulation. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
A radix guest can execute tlbie instructions to invalidate TLB entries. After a tlbie or a group of tlbies, it must then do the architected sequence eieio; tlbsync; ptesync to ensure that the TLB invalidation has been processed by all CPUs in the system before it can rely on no CPU using any translation that it just invalidated. In fact it is the ptesync which does the actual synchronization in this sequence, and hardware has a requirement that the ptesync must be executed on the same CPU thread as the tlbies which it is expected to order. Thus, if a vCPU gets moved from one physical CPU to another after it has done some tlbies but before it can get to do the ptesync, the ptesync will not have the desired effect when it is executed on the second physical CPU. To fix this, we do a ptesync in the exit path for radix guests. If there are any pending tlbies, this will wait for them to complete. If there aren't, then ptesync will just do the same as sync. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Benjamin Herrenschmidt 提交于
When a vcpu priority (CPPR) is set to a lower value (masking more interrupts), we stop processing interrupts already in the queue for the priorities that have now been masked. If those interrupts were previously re-routed to a different CPU, they might still be stuck until the older one that has them in its queue processes them. In the case of guest CPU unplug, that can be never. To address that without creating additional overhead for the normal interrupt processing path, this changes H_CPPR handling so that when such a priority change occurs, we scan the interrupt queue for that vCPU, and for any interrupt in there that has been re-routed, we replace it with a dummy and force a re-trigger. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Tested-by: NAlexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Nicholas Piggin 提交于
The current partition table unmap code clears the _PAGE_PRESENT bit out of the pte, which leaves pud_huge/pmd_huge true and does not clear pud_present/pmd_present. This can confuse subsequent page faults and possibly lead to the guest looping doing continual hypervisor page faults. Signed-off-by: NNicholas Piggin <npiggin@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Nicholas Piggin 提交于
The standard eieio ; tlbsync ; ptesync must follow tlbie to ensure it is ordered with respect to subsequent operations. Signed-off-by: NNicholas Piggin <npiggin@gmail.com> Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Paul Mackerras 提交于
Currently, the HV KVM guest entry/exit code adds the timebase offset from the vcore struct to the timebase on guest entry, and subtracts it on guest exit. Which is fine, except that it is possible for userspace to change the offset using the SET_ONE_REG interface while the vcore is running, as there is only one timebase offset per vcore but potentially multiple VCPUs in the vcore. If that were to happen, KVM would subtract a different offset on guest exit from that which it had added on guest entry, leading to the timebase being out of sync between cores in the host, which then leads to bad things happening such as hangs and spurious watchdog timeouts. To fix this, we add a new field 'tb_offset_applied' to the vcore struct which stores the offset that is currently applied to the timebase. This value is set from the vcore tb_offset field on guest entry, and is what is subtracted from the timebase on guest exit. Since it is zero when the timebase offset is not applied, we can simplify the logic in kvmhv_start_timing and kvmhv_accumulate_time. In addition, we had secondary threads reading the timebase while running concurrently with code on the primary thread which would eventually add or subtract the timebase offset from the timebase. This occurred while saving or restoring the DEC register value on the secondary threads. Although no specific incorrect behaviour has been observed, this is a race which should be fixed. To fix it, we move the DEC saving code to just before we call kvmhv_commence_exit, and the DEC restoring code to after the point where we have waited for the primary thread to switch the MMU context and add the timebase offset. That way we are sure that the timebase contains the guest timebase value in both cases. Signed-off-by: NPaul Mackerras <paulus@ozlabs.org>
-
由 Mathieu Malaterre 提交于
Directly use fault_in_pages_readable instead of manual __get_user code. Fix warning treated as error with W=1: arch/powerpc/kernel/kvm.c:675:6: error: variable ‘tmp’ set but not used [-Werror=unused-but-set-variable] Suggested-by: NChristophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: NMathieu Malaterre <malat@debian.org> Reviewed-by: NChristophe Leroy <christophe.leroy@c-s.fr> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
由 Nicholas Piggin 提交于
Implement a local TLB flush for invalidating an LPID with variants for process or partition scope. And a global TLB flush for invalidating a partition scoped page of an LPID. These will be used by KVM in subsequent patches. Signed-off-by: NNicholas Piggin <npiggin@gmail.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 15 5月, 2018 1 次提交
-
-
由 Aneesh Kumar K.V 提交于
In the next set of patches, we will switch pmd allocator to use page fragments and the locking will be updated to split pmd ptlock. We want to avoid using fragments for partition-scoped table. Use slab cache similar to level 4 table Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
-
- 07 5月, 2018 1 次提交
-
-
由 Linus Torvalds 提交于
-
- 06 5月, 2018 9 次提交
-
-
git://git.kernel.org/pub/scm/virt/kvm/kvm由 Linus Torvalds 提交于
Pll KVM fixes from Radim Krčmář: "ARM: - Fix proxying of GICv2 CPU interface accesses - Fix crash when switching to BE - Track source vcpu git GICv2 SGIs - Fix an outdated bit of documentation x86: - Speed up injection of expired timers (for stable)" * tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: KVM: x86: remove APIC Timer periodic/oneshot spikes arm64: vgic-v2: Fix proxying of cpuif access KVM: arm/arm64: vgic_init: Cleanup reference to process_maintenance KVM: arm64: Fix order of vcpu_write_sys_reg() arguments KVM: arm/arm64: vgic: Fix source vcpu issues for GICv2 SGI
-
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu由 Linus Torvalds 提交于
Pull iommu fixes from Joerg Roedel: - fix a compile warning in the AMD IOMMU driver with irq remapping disabled - fix for VT-d interrupt remapping and invalidation size (caused a BUG_ON when trying to invalidate more than 4GB) - build fix and a regression fix for broken graphics with old DTS for the rockchip iommu driver - a revert in the PCI window reservation code which fixes a regression with VFIO. * tag 'iommu-fixes-v4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu: rockchip: fix building without CONFIG_OF iommu/vt-d: Use WARN_ON_ONCE instead of BUG_ON in qi_flush_dev_iotlb() iommu/vt-d: fix shift-out-of-bounds in bug checking iommu/dma: Move PCI window region reservation back into dma specific path. iommu/rockchip: Make clock handling optional iommu/amd: Hide unused iommu_table_lock iommu/vt-d: Fix usage of force parameter in intel_ir_reconfigure_irte()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull x86 fix from Thomas Gleixner: "Unbreak the CPUID CPUID_8000_0008_EBX reload which got dropped when the evaluation of physical and virtual bits which uses the same CPUID leaf was moved out of get_cpu_cap()" * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/cpu: Restore CPUID_8000_0008_EBX reload
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull clocksource fixes from Thomas Gleixner: "The recent addition of the early TSC clocksource breaks on machines which have an unstable TSC because in case that TSC is disabled, then the clocksource selection logic falls back to the early TSC which is obviously bogus. That also unearthed a few robustness issues in the clocksource derating code which are addressed as well" * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: clocksource: Rework stale comment clocksource: Consistent de-rate when marking unstable x86/tsc: Fix mark_tsc_unstable() clocksource: Initialize cs->wd_list clocksource: Allow clocksource_mark_unstable() on unregistered clocksources x86/tsc: Always unregister clocksource_tsc_early
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull irq fix from Thomas Gleixner: "A single fix to prevent false positives in the spurious interrupt detector when more than a single demultiplex register is evaluated in the Qualcom irq combiner driver" * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: irqchip/qcom: Fix check for spurious interrupts
-
git://git.infradead.org/linux-platform-drivers-x86由 Linus Torvalds 提交于
Pull x86 platform driver fixes from Darren Hart: - We missed a case in the Dell config dependencies resulting in a possible bad configuration, resolve it by giving up on trying to keep DELL_LAPTOP visible in the menu and make it depend on DELL_SMBIOS. - Fix a null pointer dereference at module unload for the asus-wireless driver. * tag 'platform-drivers-x86-v4.17-2' of git://git.infradead.org/linux-platform-drivers-x86: platform/x86: Kconfig: Fix dell-laptop dependency chain. platform/x86: asus-wireless: Fix NULL pointer dereference
-
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb由 Linus Torvalds 提交于
Pull USB fixes from Greg KH: "Here are some USB driver fixes for 4.17-rc4. The majority of them are some USB gadget fixes that missed my last pull request. The "largest" patch in here is a fix for the old visor driver that syzbot found 6 months or so ago and I finally remembered to fix it. All of these have been in linux-next with no reported issues" * tag 'usb-4.17-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: Revert "usb: host: ehci: Use dma_pool_zalloc()" usb: typec: tps6598x: handle block reads separately with plain-I2C adapters usb: typec: tcpm: Release the role mux when exiting USB: Accept bulk endpoints with 1024-byte maxpacket xhci: Fix use-after-free in xhci_free_virt_device USB: serial: visor: handle potential invalid device configuration USB: serial: option: adding support for ublox R410M usb: musb: trace: fix NULL pointer dereference in musb_g_tx() usb: musb: host: fix potential NULL pointer dereference usb: gadget: composite Allow for larger configuration descriptors usb: dwc3: gadget: Fix list_del corruption in dwc3_ep_dequeue usb: dwc3: gadget: dwc3_gadget_del_and_unmap_request() can be static usb: dwc2: pci: Fix error return code in dwc2_pci_probe() usb: dwc2: WA for Full speed ISOC IN in DDMA mode. usb: dwc2: dwc2_vbus_supply_init: fix error check usb: gadget: f_phonet: fix pn_net_xmit()'s return type
-
由 Anthoine Bourgeois 提交于
Since the commit "8003c9ae: add APIC Timer periodic/oneshot mode VMX preemption timer support", a Windows 10 guest has some erratic timer spikes. Here the results on a 150000 times 1ms timer without any load: Before 8003c9ae | After 8003c9ae Max 1834us | 86000us Mean 1100us | 1021us Deviation 59us | 149us Here the results on a 150000 times 1ms timer with a cpu-z stress test: Before 8003c9ae | After 8003c9ae Max 32000us | 140000us Mean 1006us | 1997us Deviation 140us | 11095us The root cause of the problem is starting hrtimer with an expiry time already in the past can take more than 20 milliseconds to trigger the timer function. It can be solved by forward such past timers immediately, rather than submitting them to hrtimer_start(). In case the timer is periodic, update the target expiration and call hrtimer_start with it. v2: Check if the tsc deadline is already expired. Thank you Mika. v3: Execute the past timers immediately rather than submitting them to hrtimer_start(). v4: Rearm the periodic timer with advance_periodic_target_expiration() a simpler version of set_target_expiration(). Thank you Paolo. Cc: Mika Penttilä <mika.penttila@nextfour.com> Cc: Wanpeng Li <kernellwp@gmail.com> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: stable@vger.kernel.org Signed-off-by: NAnthoine Bourgeois <anthoine.bourgeois@blade-group.com> 8003c9ae ("KVM: LAPIC: add APIC Timer periodic/oneshot mode VMX preemption timer support") Signed-off-by: NRadim Krčmář <rkrcmar@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm由 Radim Krčmář 提交于
KVM/arm fixes for 4.17, take #2 - Fix proxying of GICv2 CPU interface accesses - Fix crash when switching to BE - Track source vcpu git GICv2 SGIs - Fix an outdated bit of documentation
-
- 05 5月, 2018 9 次提交
-
-
由 Linus Torvalds 提交于
Merge tag 'kbuild-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild Pull Kbuild fixes from Masahiro Yamada: - remove state comment in modpost - extend MAINTAINERS entry to cover modpost and more makefiles - fix missed building of SANCOV gcc-plugin - replace left-over 'bison' with $(YACC) - display short log when generating parer of genksyms * tag 'kbuild-fixes-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: genksyms: fix typo in parse.tab.{c,h} generation rules kbuild: replace hardcoded bison in cmd_bison_h with $(YACC) gcc-plugins: fix build condition of SANCOV plugin MAINTAINERS: Update Kbuild entry with a few paths modpost: delete stale comment
-
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux由 Linus Torvalds 提交于
Pull clk fixes froom Stephen Boyd: "A handful of fixes for the stm32mp1 clk driver came in during the merge window for the driver that got merged in the merge window. Plus a warning fix for unused PM ops and a couple fixes for the meson clk driver clk names that went unnoticed with the regmap rework. There's also another fix in here for the mux rounding flag which wasn't doing what it said it did, but now it does" * tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: clk: meson: meson8b: fix meson8b_cpu_clk parent clock name clk: meson: meson8b: fix meson8b_fclk_div3_div clock name clk: meson: drop meson_aoclk_gate_regmap_ops clk: meson: honor CLK_MUX_ROUND_CLOSEST in clk_regmap clk: honor CLK_MUX_ROUND_CLOSEST in generic clk mux clk: cs2000: mark resume function as __maybe_unused clk: stm32mp1: remove ck_apb_dbg clock clk: stm32mp1: set stgen_k clock as critical clk: stm32mp1: add missing tzc2 clock clk: stm32mp1: fix SAI3 & SAI4 clocks clk: stm32mp1: remove unused dfsdm_src[] const clk: stm32mp1: add missing static
-
git://github.com/andersson/remoteproc由 Linus Torvalds 提交于
Pull remoteproc and rpmsg fixes from Bjorn Andersson: - fix screw-up when reversing boolean for rproc_stop() - add missing OF node refcounting dereferences - add missing MODULE_ALIAS in rpmsg_char * tag 'rproc-v4.17-1' of git://github.com/andersson/remoteproc: rpmsg: added MODULE_ALIAS for rpmsg_char remoteproc: qcom: Fix potential device node leaks remoteproc: fix crashed parameter logic on stop call
-
git://people.freedesktop.org/~airlied/linux由 Linus Torvalds 提交于
Pull drm fixes from Dave Airlie: "vmwgfx, i915, vc4, vga dac fixes. This seems eerily quiet, so I expect it will explode next week or something. One i915 model firmware, two vmwgfx fixes, one vc4 fix and one bridge leak fix" * tag 'drm-fixes-for-v4.17-rc4' of git://people.freedesktop.org/~airlied/linux: drm/bridge: vga-dac: Fix edid memory leak drm/vc4: Make sure vc4_bo_{inc,dec}_usecnt() calls are balanced drm/i915/glk: Add MODULE_FIRMWARE for Geminilake drm/vmwgfx: Fix a buffer object leak drm/vmwgfx: Clean up fbdev modeset locking
-
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace由 Linus Torvalds 提交于
Pull tracing fixes from Steven Rostedt: "Some of the files in the tracing directory show file mode 0444 when they are writable by root. To fix the confusion, they should be 0644. Note, either case root can still write to them. Zhengyuan asked why I never applied that patch (the first one is from 2014!). I simply forgot about it. /me lowers head in shame" * tag 'trace-v4.17-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: tracing: Fix the file mode of stack tracer ftrace: Have set_graph_* files have normal file modes
-
git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma由 Linus Torvalds 提交于
Pull rdma fixes from Doug Ledford: "This is our first pull request of the rc cycle. It's not that it's been overly quiet, we were just waiting on a few things before sending this off. For instance, the 6 patch series from Intel for the hfi1 driver had actually been pulled in on Tuesday for a Wednesday pull request, only to have Jason notice something I missed, so we held off for some testing, and then on Thursday had to respin the series because the very first patch needed a minor fix (unnecessary cast is all). There is a sizable hns patch series in here, as well as a reasonably largish hfi1 patch series, then all of the lines of uapi updates are just the change to the new official Linux-OpenIB SPDX tag (a bunch of our files had what amounts to a BSD-2-Clause + MIT Warranty statement as their license as a result of the initial code submission years ago, and the SPDX folks decided it was unique enough to warrant a unique tag), then the typical mlx4 and mlx5 updates, and finally some cxgb4 and core/cache/cma updates to round out the bunch. None of it was overly large by itself, but in the 2 1/2 weeks we've been collecting patches, it has added up :-/. As best I can tell, it's been through 0day (I got a notice about my last for-next push, but not for my for-rc push, but Jason seems to think that failure messages are prioritized and success messages not so much). It's also been through linux-next. And yes, we did notice in the context portion of the CMA query gid fix patch that there is a dubious BUG_ON() in the code, and have plans to audit our BUG_ON usage and remove it anywhere we can. Summary: - Various build fixes (USER_ACCESS=m and ADDR_TRANS turned off) - SPDX license tag cleanups (new tag Linux-OpenIB) - RoCE GID fixes related to default GIDs - Various fixes to: cxgb4, uverbs, cma, iwpm, rxe, hns (big batch), mlx4, mlx5, and hfi1 (medium batch)" * tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (52 commits) RDMA/cma: Do not query GID during QP state transition to RTR IB/mlx4: Fix integer overflow when calculating optimal MTT size IB/hfi1: Fix memory leak in exception path in get_irq_affinity() IB/{hfi1, rdmavt}: Fix memory leak in hfi1_alloc_devdata() upon failure IB/hfi1: Fix NULL pointer dereference when invalid num_vls is used IB/hfi1: Fix loss of BECN with AHG IB/hfi1 Use correct type for num_user_context IB/hfi1: Fix handling of FECN marked multicast packet IB/core: Make ib_mad_client_id atomic iw_cxgb4: Atomically flush per QP HW CQEs IB/uverbs: Fix kernel crash during MR deregistration flow IB/uverbs: Prevent reregistration of DM_MR to regular MR RDMA/mlx4: Add missed RSS hash inner header flag RDMA/hns: Fix a couple misspellings RDMA/hns: Submit bad wr RDMA/hns: Update assignment method for owner field of send wqe RDMA/hns: Adjust the order of cleanup hem table RDMA/hns: Only assign dqpn if IB_QP_PATH_DEST_QPN bit is set RDMA/hns: Remove some unnecessary attr_mask judgement RDMA/hns: Only assign mtu if IB_QP_PATH_MTU bit is set ...
-
git://git.kernel.dk/linux-block由 Linus Torvalds 提交于
Pull block fixes from Jens Axboe: "A collection of fixes that should to into this release. This contains: - Set of bcache fixes from Coly, fixing regression in patches that went into this series. - Set of NVMe fixes by way of Keith. - Set of bdi related fixes, one from Jan and two from Tetsuo Handa, fixing various issues around device addition/removal. - Two block inflight fixes from Omar, fixing issues around the transition to using tags for blk-mq inflight accounting that we did a few releases ago" * tag 'for-linus-20180504' of git://git.kernel.dk/linux-block: bdi: Fix oops in wb_workfn() nvmet: switch loopback target state to connecting when resetting nvme/multipath: Fix multipath disabled naming collisions nvme/multipath: Disable runtime writable enabling parameter nvme: Set integrity flag for user passthrough commands nvme: fix potential memory leak in option parsing bdi: Fix use after free bug in debugfs_remove() bdi: wake up concurrent wb_shutdown() callers. bcache: use pr_info() to inform duplicated CACHE_SET_IO_DISABLE set bcache: set dc->io_disable to true in conditional_stop_bcache_device() bcache: add wait_for_kthread_stop() in bch_allocator_thread() bcache: count backing device I/O error for writeback I/O bcache: set CACHE_SET_IO_DISABLE in bch_cached_dev_error() bcache: store disk name in struct cache and struct cached_dev blk-mq: fix sysfs inflight counter blk-mq: count allocated but not started requests in iostats inflight
-
git://git.kernel.org/pub/scm/fs/xfs/xfs-linux由 Linus Torvalds 提交于
Pull xfs fixes from Darrick Wong: "I've got one more bug fix for xfs for 4.17-rc4, which caps the amount of data we try to handle in one dedupe request so that userspace can't livelock the kernel. This series has been run through a full xfstests run during the week and through a quick xfstests run against this morning's master, with no ajor failures reported. Summary: - Cap the maximum length of a deduplication request at MAX_RW_COUNT/2 to avoid kernel livelock due to excessively large IO requests" * tag 'xfs-4.17-fixes-2' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux: xfs: cap the length of deduplication requests
-
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux由 Linus Torvalds 提交于
Pull btrfs fixes from David Sterba: "Two regression fixes and one fix for stable" * tag 'for-4.17-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: Btrfs: send, fix missing truncate for inode with prealloc extent past eof btrfs: Take trans lock before access running trans in check_delayed_ref btrfs: Fix wrong first_key parameter in replace_path
-