Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Those standards use 6 MHz firmware.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Whilst reanalysing my formulas I realised it was no longer possible to get the
right values for a 36.1667MHz IF due to rounding problems.

Storing frequencies in units of 0.1kHz makes it possible to calculate these
again correctly.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are at least three variants of the DViCO FusionHDTV DVB-T NANO that
share the same USB device ID.  The first (ZL10353 w/ firmware in ROM) is
already supported; the latter two both require firmware and have either
an MT352 or ZL10353 demodulator, and have a different IR receiver from the
first.

This introduces a new identify_state that can tell the difference between a
"warm" device which is running the embedded firmware, and a "cold" device
that needs us to upload firmware to it before it will work.  We patch the
uploaded device ID (like we do for other bluebird devices) to make it easy
to identify the particular device variant when it reattaches.

NB: These devices use a different firmware file from previous bluebird
    devices.  You need a new firmware file to make this work.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rework the input frequency calculation so that it produces the right values
when the ADC oversamples the IF input.

This means MT352 devices can now process a near-zero IF (according to the,
specs 4.57MHz is supported with the default crystal).
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for the DViCO FusionHDTV DVB-T NANO with zl10353 demodulator and
firmware in ROM on the device.

Again, this is based on the great work of Mike Krufky with my modifications
to use the in-tree XC2028 driver.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV.  Mask them off when finding
the firmware to load.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When loading BASE firmware, we must use std = 0.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add support for DViCO's Dual Digital 4 with xc3028 tuner, zl10353 DVB-T
demodulator and a new-style I2C IR remote control receiver.

This would not have been possible without the work of and advice from
Mike Krufky, who originally got the Dual Digital 4 and second-gen DVB-T
NANO devices working with the out-of-tree XC3028 driver.

I converted it to use the in-tree XC3028 driver (after making it suitable
for our use), and added the IR remote control support based on his advice.

NB: a firmware package is required to use this device.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In practice, the tuner occasionally fails to respond correctly after a
firmware load.  Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs.  By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware.  This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.

Add a structure to remember what firmware properties we have.  This
contains the currently loaded/wanted  base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.

Incorporate said structure into the tuner private data.

When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible.  This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There is no need to duplicate the max_len field from the ctrl structure
in the private data.  If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.

Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.

Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops.  Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The frequency divisor should only be four bytes long.  Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Hold the private lock over set_config and set priv->firm_size to 0 after a
failed firmware load to prevent firmware accidentally being freed on us.

Clean up the firmware load/error messages somewhat and rename priv->version
to priv->firm_version to make it clear which "version" it is.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add break to stop us from following the default failure path even upon success.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Protect refcount changes and modifications to xc2028_list with a mutex.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Cast v4l2_std_id variables to unsigned long long so they will printk properly.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix some missing spaces in errors that may be emitted during attach failure.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Issuing register reads as a separate address write and data read transactions
means that other I2C activity could occur in between and state could get out
of sync.  Issue both the write and read in a single transaction so that the
i2c layer can prevent other users accessing the bus until we are complete.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

strcasecmp returns 0 on match, not true.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The I2C macros have side effects and send_seq could cause a return from
a function with a mutex held.  Change them to behave like real functions.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now we know the zl10353's correct ADC clock, we can calculate the input
frequency registers correctly instead of just blindly setting them.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Issue FSM_GO instead of TUNER_GO if there is no tuner attached to the
secondary i2c bus.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The path to perform a read immediately after a write was not checking that
the address being read from was the same as the one that was written.

Handling this case correctly should mean that we now can handle more than
two i2c messages at a time.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Any i2c read request that was not immediately preceded by a write request was
incorrectly taking the write path.  Add the capability to handle individual
read requests.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The i2c master_xfer routine should return a negative result if not all
transfers completed successfully.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Callers to cxusb_ctrl_msg currently do not receive any indication that their
transfer failed.  Return the true return code from dvb_usb_generic_{rw,write}.
Signed-off-by: NChris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The saa7134-oss is deprecated for quite some time, it's the only remaining OSS
user outside of sound/oss/, and considering how few and what kind of
soundcards are left supported by OSS I hardly see any use cases left.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If tda827x_config hasn't been defined, exit the function.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix the following oops:

[  750.807586] CPU:    1
[  750.807587] EIP:    0060:[<f9dde2a3>]    Tainted: P       VLI
[  750.807589] EFLAGS: 00010296   (2.6.22-14-generic #1)
[  750.807599] EIP is at tda827x_probe_version+0xc3/0x130 [tda827x]
[  750.807603] eax: 00000000   ebx: f5a45a00   ecx: 00000000   edx: 00000001
[  750.807607] esi: f9de05ac   edi: e9b897e0   ebp: ed8015ac   esp: ed735f58
[  750.807611] ds: 007b   es: 007b   fs: 00d8  gs: 0000  ss: 0068
[  750.807615] Process kdvb-fe-1 (pid: 10662, ti=ed734000 task=d3b76530 task.ti=ed734000)
[  750.807618] Stack: f9e23972 00000038 ed735fd0 00010060 41ae0001 ed735f73 88b89608 e9b89608
[  750.807629]        e9b89608 ed801400 f9dde338 e9b89608 f9b2a46b 000000ae 00000a18 d3b76640
[  750.807639]        fffffffc f9b2bad6 00000003 f4433e68 e962b8c0 f4433e64 00000292 ed735fd0
[  750.807649] Call Trace:
[  750.807653]  [<f9e23972>] tda10046_init+0x2d2/0x6c0 [tda1004x]
[  750.807700]  [<f9dde338>] tda827x_initial_init+0x8/0x20 [tda827x]
[  750.807713]  [<f9b2a46b>] dvb_frontend_init+0x2b/0x60 [dvb_core]
[  750.807745]  [<f9b2bad6>] dvb_frontend_thread+0x66/0x2f0 [dvb_core]
[  750.807780]  [complete+64/96] complete+0x40/0x60
[  750.807805]  [<f9b2ba70>] dvb_frontend_thread+0x0/0x2f0 [dvb_core]
[  750.807822]  [kthread+66/112] kthread+0x42/0x70
[  750.807828]  [kthread+0/112] kthread+0x0/0x70
[  750.807841]  [kernel_thread_helper+7/16] kernel_thread_helper+0x7/0x10
[  750.807869]  =======================
[  750.807872] Code: 8b 74 24 20 8b 7c 24 24 83 c4 28 c3 8b 0d 00 0c de f9 85 c9 75 42 be e0 04 de f9 81 c7 0c 01 00 00 b9 33 00 00 00 f3 a5 8b 43 08 <c7> 40 14 50 e3 dd f9 8b 5c 24 1c 31 c0 8b 74 24 20 8b 7c 24 24
[  750.807925] EIP: [<f9dde2a3>] tda827x_probe_version+0xc3/0x130 [tda827x] SS:ESP 0068:ed735f58
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The ability to read Hauppauge eeprom's was recently added to saa7134,
so we must build the tveeprom module.

Thanks to Matthias Schwarzott for pointing this out.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The HVR-900 requires the MTS version of the xc3028 firmware in order
to get any sound. The below patch selects this firmware variant on
HVR-900 cards, as well as splitting the HVR-950 into its own entry
(since I don't know if it uses the MTS variant and it will have to be
split off eventually anyway).
Signed-off-by: NAidan Thornton <makosoft@googlemail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>