There's no need to have these defines in plat/io.h.

Note that we now need to ifdef omap_read/write calls
as they will be available for omap1 only.

While at it, clean up the includes to group them like
they typically are grouped.
Signed-off-by: NTony Lindgren <tony@atomide.com>

"hdmi_hpd" pin is muxed to INPUT and PULLUP, but the pin is not
currently used, and in the future when it is used, the pin is used as a
GPIO and is board specific, not an OMAP4 wide thing.

So remove the muxing for now.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>

Disables the internal pull resistor for SDA and SCL which are enabled by
default, as there are external pull up's in 4460 and 4430 ES2.3
SDP, Blaze and Panda Boards, It is done to avoid the EDID read failure.
Signed-off-by: NRicardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Move duplicate HDMI mux_init code from omap4 and panda board file
to display file.
Signed-off-by: NMythri P K <mythripk@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

ARM restart changes needed changes to common.h to make it local.
This conflicted with v3.2-rc4 DSS related hwmod changes that
git mergetool was not able to handle.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Resetting DISPC when a DISPC output is enabled causes the DSS to go into an
inconsistent state. Thus if the bootloader has enabled a display, the hwmod code
cannot reset the DISPC module just like that, but the outputs need to be
disabled first.

Add function dispc_disable_outputs() which disables all active overlay manager
and ensure all frame transfers are completed.

Modify omap_dss_reset() to call this function and clear DSS_CONTROL,
DSS_SDI_CONTROL and DSS_PLL_CONTROL so that DSS is in a clean state when the
DSS2 driver starts.

This resolves the hang issue(caused by a L3 error during boot) seen on the
beagle board C3, which has a factory bootloader that enables display. The issue
is resolved with this patch.

Thanks to Tomi and Sricharan for some additional testing.
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: NR, Sricharan <r.sricharan@ti.com>
Signed-off-by: NArchit Taneja <archit@ti.com>
[paul@pwsan.com: restructured code, removed omap_{read,write}l(), removed
 cpu_is_omap*() calls and converted to dev_attr]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

This patch adds a custom DSS reset function used on OMAPs from OMAP2
forward.

The function doesn't actually do a reset, it only waits for the reset to
complete. The reason for this is that on OMAP4 there is no possibility
to do a SW reset, and on OMAP2/3 doing a SW reset for dss_core resets
all the other DSS modules also, thus breaking the HWMOD model where
every DSS module is handled independently.

This fixes the problem with DSS reset on OMAP4, caused by the fact that
because there's no SW reset for dss_core on OMAP4, the HWMOD framework
doesn't try to reset dss_core and thus the DSS clocks were never enabled
at the same time. This causes causes the HWMOD reset to fail for
dss_dispc and dss_rfbi.

The common reset function will also allow us to fix another problem in
the future: before doing a reset we need to disable DSS outputs, which
are in some cases enabled by the bootloader, as otherwise DSS HW seems
to get more or less stuck, requiring a power reset to recover.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
[paul@pwsan.com: modified to build arch/arm/mach-omap2/display.o
 unconditionally to avoid an error when !CONFIG_OMAP2_DSS]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

To fix things like this:

arch/arm/mach-omap2/usb-tusb6010.c:58: error: implicit declaration of function 'memset'
arch/arm/kernel/leds.c:40: error: implicit declaration of function 'strcspn'
arch/arm/kernel/leds.c:40: warning: incompatible implicit declaration of built-in function 'strcspn'
arch/arm/kernel/leds.c:45: error: implicit declaration of function 'strncmp'
arch/arm/kernel/leds.c:55: error: implicit declaration of function 'strlen'
arch/arm/kernel/leds.c:55: warning: incompatible implicit declaration of built-in function 'strlen'
arch/arm/mach-omap2/clockdomain.c:52: error: implicit declaration of function 'strcmp'
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Remove all these duplicated structures since a default one is now
available.
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

Implement dsi_mux_pads for OMAP4. On enable the function enables the DSI
pins and disables pull down. On disable the function disables the pins
and enables pull down.

It is unclear from the TRM whether the pull down is active if the pins
are disabled, so this implementation may leave the pins floating when
the DSI device is disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

dsi_mux_pads() needs to know about the DSI HW module and the DSI lanes
used. Split the function into two, enable and disable, which take
necessary arguments, and add empty implementations for both.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, there are 2 differently named platform devices generated for
the 2 DSS DSI modules. In order to use the same driver, the dsi devices
should be 2 instances of the same platform device.

Change the platform device names from "omapdss_dsi1" and "omapdss_dsi2"
to omapdss_dsi", and set the device indices to 0 and 1.
Signed-off-by: NArchit Taneja <archit@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

All of the device init and device driver interaction with omap_device
is done using platform_device pointers.  To make this more explicit,
have omap_device return a platform_device pointer instead of an
omap_device pointer.

All current users of the omap_device pointer were only using it to get
at the platform_device pointer or struct device pointer, so fixing all
of the users was trivial.

This also makes it more difficult for device init code to directly
access members of struct omap_device, and allows for easier changing
of omap_device internals.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

oh_core variable is no longer used, so it and its initialization can be
removed.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

opt_clock_available() is no longer needed, so remove it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Initialize get_context_loss_count in the DSS board data to
omap_pm_get_dev_context_loss_count, so that omapdss driver can use it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

The function to get device's context loss count has changed from

omap_pm_get_last_off_on_transaction_id() to
omap_pm_get_dev_context_loss_count()

Change name of the function pointer in omapdss.h accordingly, and use
the term "context loss count" instead of "context id" in the code.

Restructure the context loss count functions to handle errors properly,
and ensure that context is always considered lost if an error happens.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Currently, omap_display_init() maintains arrays for hwmod name(oh_name) and the
correspnding platform_device name(dev_name) needed by omap_device_build().
A variable oh_count keeps a track of the number of devices to build from oh_name
based on what omap revision it is.

Clean this up by maintaining an array of omap_dss_hwmod_data struct which is
defined for each omap revision as suggested by Tomi Valkeinen. Assign the
corresponding omap_dss_hwmod_data array struct to the pointer curr_dss_hwmod in
omap_display_init().
Signed-off-by: NArchit Taneja <archit@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

arch/arm/plat-omap/include/plat/display.h is an include for the OMAP DSS
driver. A more logical place for it is in include/video.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Provide a function in pdata to allow dss submodules to check if a given
clock is available on a platform as an optional clock.
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
(based on implementation from Senthil)
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Add hwmod device names for OMAP4; this enables device build for omap4 dss
hwmod IPs.
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NMayuresh Janorkar <mayur@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

Looks up the hwmod database for each of the given DSS HW IP and builds
omap_device which inturn does the platform device register for each of DSS HW IP
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>

A new file display.c is introduced for display driver init, which adds a function
omap_display_init to do the DSS driver registration. This is the first step in moving
away registration of DSS from board files into a common place.
Reviewed-by: NKevin Hilman <khilman@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NSenthilvadivu Guruswamy <svadivu@ti.com>
Signed-off-by: NSumit Semwal <sumit.semwal@ti.com>
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>