Currently packets with non-hardware-accelerated vlan cannot be handled
by GRO. This causes low performance for 802.1ad and stacked vlan, as their
vlan tags are currently not stripped by hardware.

This patch adds GRO support for non-hardware-accelerated vlan and
improves receive performance of them.

Test Environment:
 vlan device (.1Q) on vlan device (.1ad) on ixgbe (82599)

Result:

- Before

$ netperf -t TCP_STREAM -H 192.168.20.2 -l 60
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec

 87380  16384  16384    60.00    5233.17

Rx side CPU usage:
  %usr      %sys      %irq     %soft     %idle
  0.27     58.03      0.00     41.70      0.00

- After

$ netperf -t TCP_STREAM -H 192.168.20.2 -l 60
Recv   Send    Send
Socket Socket  Message  Elapsed
Size   Size    Size     Time     Throughput
bytes  bytes   bytes    secs.    10^6bits/sec

 87380  16384  16384    60.00    7586.85

Rx side CPU usage:
  %usr      %sys      %irq     %soft     %idle
  0.50     25.83      0.00     59.53     14.14

[ Register VLAN offloads with priority 10 -DaveM ]
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently vlan notifier handler will try to update all vlans
for a device when that device comes up.  A problem occurs,
however, when the vlan device was set to promiscuous, but not
by the user (ex: a bridge).  In that case, dev->gflags are
not updated.  What results is that the lower device ends
up with an extra promiscuity count.  Here are the
backtraces that prove this:
[62852.052179]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.052186]  [<ffffffff8160bcbb>] ? _raw_spin_unlock_bh+0x1b/0x40
[62852.052188]  [<ffffffff814fe4be>] ? dev_set_rx_mode+0x2e/0x40
[62852.052190]  [<ffffffff814fe694>] dev_set_promiscuity+0x24/0x50
[62852.052194]  [<ffffffffa0324795>] vlan_dev_open+0xd5/0x1f0 [8021q]
[62852.052196]  [<ffffffff814fe58f>] __dev_open+0xbf/0x140
[62852.052198]  [<ffffffff814fe88d>] __dev_change_flags+0x9d/0x170
[62852.052200]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60

The above comes from the setting the vlan device to IFF_UP state.

[62852.053569]  [<ffffffff814fe248>] __dev_set_promiscuity+0x38/0x1e0
[62852.053571]  [<ffffffffa032459b>] ? vlan_dev_set_rx_mode+0x2b/0x30
[8021q]
[62852.053573]  [<ffffffff814fe8d5>] __dev_change_flags+0xe5/0x170
[62852.053645]  [<ffffffff814fe989>] dev_change_flags+0x29/0x60
[62852.053647]  [<ffffffffa032334a>] vlan_device_event+0x18a/0x690
[8021q]
[62852.053649]  [<ffffffff8161036c>] notifier_call_chain+0x4c/0x70
[62852.053651]  [<ffffffff8109d456>] raw_notifier_call_chain+0x16/0x20
[62852.053653]  [<ffffffff814f744d>] call_netdevice_notifiers+0x2d/0x60
[62852.053654]  [<ffffffff814fe1a3>] __dev_notify_flags+0x33/0xa0
[62852.053656]  [<ffffffff814fe9b2>] dev_change_flags+0x52/0x60
[62852.053657]  [<ffffffff8150cd57>] do_setlink+0x397/0xa40

And this one comes from the notification code.  What we end
up with is a vlan with promiscuity count of 1 and and a physical
device with a promiscuity count of 2.  They should both have
a count 1.

To resolve this issue, vlan code can use dev_get_flags() api
which correctly masks promiscuity and allmulti flags.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't use dev->iflink anymore.

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Stacked vlan devices curretly have few features (GRO, HIGHDMA, LLTX).
Since we have software fallbacks in case the NIC can not handle some
features for multiple vlans, we can add the same features as the lower
vlan devices for stacked vlan devices.

This allows stacked vlan devices to create large (GSO) packets and not to
segment packets. Those packets will be segmented by software on the real
device, or even can be segmented by the NIC once TSO for multiple vlans
becomes enabled by the following patches.

The exception is those related to FCoE, which does not have a software
fallback.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a networking device is taken down that has a non-trivial number
of VLAN devices configured under it, we eat a full synchronize_net()
for every such VLAN device.

This is because of the call chain:

	NETDEV_DOWN notifier
	--> vlan_device_event()
		--> dev_change_flags()
		--> __dev_change_flags()
		--> __dev_close()
		--> __dev_close_many()
		--> dev_deactivate_many()
			--> synchronize_net()

This is kind of rediculous because we already have infrastructure for
batching doing operation X to a list of net devices so that we only
incur one sync.

So make use of that by exporting dev_close_many() and adjusting it's
interfaace so that the caller can fully manage the batch list.  Use
this in vlan_device_event() and all the overhead goes away.
Reported-by: NSalam Noureddine <noureddine@arista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the built-in function instead of memset.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that there are no more users kill dev_rebuild_header and all of it's
implementations.

This is long overdue.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is
added to rtnetlink messages.
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the real device can segment packets by software, a vlan device
can set TSO/UFO even when the real device doesn't have those features.
Unlike GSO, this allows packets to be segmented after Qdisc.
Signed-off-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a6111d3c "vlan: Pass SIOC[SG]HWTSTAMP ioctls to real device"
intended to enable hardware time stamping on VLAN interfaces, but
passing SIOCSHWTSTAMP is only half of the story. This patch adds
the second half, by letting user space find out the time stamping
capabilities of the device backing a VLAN interface.
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Always returns the same skb it gets, so change to void.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NPravin B Shelar <pshelar@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Testing xmit_more support with netperf and connected UDP sockets,
I found strange dst refcount false sharing.

Current handling of IFF_XMIT_DST_RELEASE is not optimal.

Dropping dst in validate_xmit_skb() is certainly too late in case
packet was queued by cpu X but dequeued by cpu Y

The logical point to take care of drop/force is in __dev_queue_xmit()
before even taking qdisc lock.

As Julian Anastasov pointed out, need for skb_dst() might come from some
packet schedulers or classifiers.

This patch adds new helper to cleanly express needs of various drivers
or qdiscs/classifiers.

Drivers that need skb_dst() in their ndo_start_xmit() should call
following helper in their setup instead of the prior :

	dev->priv_flags &= ~IFF_XMIT_DST_RELEASE;
->
	netif_keep_dst(dev);

Instead of using a single bit, we use two bits, one being
eventually rebuilt in bonding/team drivers.

The other one, is permanent and blocks IFF_XMIT_DST_RELEASE being
rebuilt in bonding/team. Eventually, we could add something
smarter later.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Julian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the functionality to untag traffic on input resides
as part of the vlan module and is build only when VLAN support
is enabled in the kernel.  When VLAN is disabled, the function
vlan_untag() turns into a stub and doesn't really untag the
packets.  This seems to create an interesting interaction
between VMs supporting checksum offloading and some network drivers.

There are some drivers that do not allow the user to change
tx-vlan-offload feature of the driver.  These drivers also seem
to assume that any VLAN-tagged traffic they transmit will
have the vlan information in the vlan_tci and not in the vlan
header already in the skb.  When transmitting skbs that already
have tagged data with partial checksum set, the checksum doesn't
appear to be updated correctly by the card thus resulting in a
failure to establish TCP connections.

The following is a packet trace taken on the receiver where a
sender is a VM with a VLAN configued.  The host VM is running on
doest not have VLAN support and the outging interface on the
host is tg3:
10:12:43.503055 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27243,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x48d9), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294837885 ecr 0,nop,wscale 7], length 0
10:12:44.505556 52:54:00:ae:42:3f > 28:d2:44:7d:c2:de, ethertype 802.1Q
(0x8100), length 78: vlan 100, p 0, ethertype IPv4, (tos 0x0, ttl 64, id 27244,
offset 0, flags [DF], proto TCP (6), length 60)
    10.0.100.1.58545 > 10.0.100.10.ircu-2: Flags [S], cksum 0xdc39 (incorrect
-> 0x44ee), seq 1069378582, win 29200, options [mss 1460,sackOK,TS val
4294838888 ecr 0,nop,wscale 7], length 0

This connection finally times out.

I've only access to the TG3 hardware in this configuration thus have
only tested this with TG3 driver.  There are a lot of other drivers
that do not permit user changes to vlan acceleration features, and
I don't know if they all suffere from a similar issue.

The patch attempt to fix this another way.  It moves the vlan header
stipping code out of the vlan module and always builds it into the
kernel network core.  This way, even if vlan is not supported on
a virtualizatoin host, the virtual machines running on top of such
host will still work with VLANs enabled.

CC: Patrick McHardy <kaber@trash.net>
CC: Nithin Nayak Sujir <nsujir@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly, vlan will create  /proc/net/vlan/<dev>, so when we
create dev with name "config", it will confict with
/proc/net/vlan/config.
Reported-by: NStephane Chazelas <stephane.chazelas@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend alloc_netdev{,_mq{,s}}() to take name_assign_type as argument, and convert
all users to pass NET_NAME_UNKNOWN.

Coccinelle patch:

@@
expression sizeof_priv, name, setup, txqs, rxqs, count;
@@

(
-alloc_netdev_mqs(sizeof_priv, name, setup, txqs, rxqs)
+alloc_netdev_mqs(sizeof_priv, name, NET_NAME_UNKNOWN, setup, txqs, rxqs)
|
-alloc_netdev_mq(sizeof_priv, name, setup, count)
+alloc_netdev_mq(sizeof_priv, name, NET_NAME_UNKNOWN, setup, count)
|
-alloc_netdev(sizeof_priv, name, setup)
+alloc_netdev(sizeof_priv, name, NET_NAME_UNKNOWN, setup)
)

v9: move comments here from the wrong commit
Signed-off-by: NTom Gundersen <teg@jklm.no>
Reviewed-by: NDavid Herrmann <dh.herrmann@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This allows applications to enable hardware timestamping without being aware
of it being a vlan device and figuring out the real device.
Signed-off-by: NStefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Madalin-Cristian reported crashs happening after a recent commit
(5a4ae5f6 "vlan: unnecessary to check if vlan_pcpu_stats is NULL")

-----------------------------------------------------------------------
root@p5040ds:~# vconfig add eth8 1
root@p5040ds:~# vconfig rem eth8.1
Unable to handle kernel paging request for data at address 0x2bc88028
Faulting instruction address: 0xc058e950
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=8 CoreNet Generic
Modules linked in:
CPU: 3 PID: 2167 Comm: vconfig Tainted: G        W     3.16.0-rc3-00346-g65e85bf #2
task: e7264d90 ti: e2c2c000 task.ti: e2c2c000
NIP: c058e950 LR: c058ea30 CTR: c058e900
REGS: e2c2db20 TRAP: 0300   Tainted: G        W      (3.16.0-rc3-00346-g65e85bf)
MSR: 00029002 <CE,EE,ME>  CR: 48000428  XER: 20000000
DEAR: 2bc88028 ESR: 00000000
GPR00: c047299c e2c2dbd0 e7264d90 00000000 2bc88000 00000000 ffffffff 00000000
GPR08: 0000000f 00000000 000000ff 00000000 28000422 10121928 10100000 10100000
GPR16: 10100000 00000000 c07c5968 00000000 00000000 00000000 e2c2dc48 e7838000
GPR24: c07c5bac c07c58a8 e77290cc c07b0000 00000000 c05de6c0 e7838000 e2c2dc48
NIP [c058e950] vlan_dev_get_stats64+0x50/0x170
LR [c058ea30] vlan_dev_get_stats64+0x130/0x170
Call Trace:
[e2c2dbd0] [ffffffea] 0xffffffea (unreliable)
[e2c2dc20] [c047299c] dev_get_stats+0x4c/0x140
[e2c2dc40] [c0488ca8] rtnl_fill_ifinfo+0x3d8/0x960
[e2c2dd70] [c0489f4c] rtmsg_ifinfo+0x6c/0x110
[e2c2dd90] [c04731d4] rollback_registered_many+0x344/0x3b0
[e2c2ddd0] [c047332c] rollback_registered+0x2c/0x50
[e2c2ddf0] [c0476058] unregister_netdevice_queue+0x78/0xf0
[e2c2de00] [c058d800] unregister_vlan_dev+0xc0/0x160
[e2c2de20] [c058e360] vlan_ioctl_handler+0x1c0/0x550
[e2c2de90] [c045d11c] sock_ioctl+0x28c/0x2f0
[e2c2deb0] [c010d070] do_vfs_ioctl+0x90/0x7b0
[e2c2df20] [c010d7d0] SyS_ioctl+0x40/0x80
[e2c2df40] [c000f924] ret_from_syscall+0x0/0x3c

Fix this problem by freeing percpu stats from dev->destructor() instead
of ndo_uninit()
Reported-by: NMadalin-Cristian Bucur <madalin.bucur@freescale.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NMadalin-Cristian Bucur <madalin.bucur@freescale.com>
Fixes: 5a4ae5f6 ("vlan: unnecessary to check if vlan_pcpu_stats is NULL")
Cc: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

skb_cow called in vlan_reorder_header does not free the skb when it failed,
and vlan_reorder_header returns NULL to reset original skb when it is called
in vlan_untag, lead to a memory leak.
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When combining real_dev's features and vlan_features, simple
bitwise AND is used. This doesn't work well for checksum
offloading features as if one set has NETIF_F_HW_CSUM and the
other NETIF_F_IP_CSUM and/or NETIF_F_IPV6_CSUM, we end up with
no checksum offloading. However, from the logical point of view
(how can_checksum_protocol() works), NETIF_F_HW_CSUM contains
the functionality of NETIF_F_IP_CSUM and NETIF_F_IPV6_CSUM so
that the result should be IP/IPV6.

Add helper function netdev_intersect_features() implementing
this logic and use it in vlan_dev_fix_features().
Signed-off-by: NMichal Kubecek <mkubecek@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit dc8eaaa0.
	vlan: Fix lockdep warning when vlan dev handle notification

Instead we use the new new API to find the lock subclass of
our vlan device.  This way we can support configurations where
vlans are interspersed with other devices:
  bond -> vlan -> macvlan -> vlan
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __vlan_find_dev_deep should always called in RCU, according
David's suggestion, rename to __vlan_find_dev_deep_rcu looks more
reasonable.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

if allocating memory for vlan_pcpu_stats failed, the device can not be operated
Signed-off-by: NLi RongQing <roy.qing.li@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When I open the LOCKDEP config and run these steps:

modprobe 8021q
vconfig add eth2 20
vconfig add eth2.20 30
ifconfig eth2 xx.xx.xx.xx

then the Call Trace happened:

[32524.386288] =============================================
[32524.386293] [ INFO: possible recursive locking detected ]
[32524.386298] 3.14.0-rc2-0.7-default+ #35 Tainted: G           O
[32524.386302] ---------------------------------------------
[32524.386306] ifconfig/3103 is trying to acquire lock:
[32524.386310]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386326]
[32524.386326] but task is already holding lock:
[32524.386330]  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386341]
[32524.386341] other info that might help us debug this:
[32524.386345]  Possible unsafe locking scenario:
[32524.386345]
[32524.386350]        CPU0
[32524.386352]        ----
[32524.386354]   lock(&vlan_netdev_addr_lock_key/1);
[32524.386359]   lock(&vlan_netdev_addr_lock_key/1);
[32524.386364]
[32524.386364]  *** DEADLOCK ***
[32524.386364]
[32524.386368]  May be due to missing lock nesting notation
[32524.386368]
[32524.386373] 2 locks held by ifconfig/3103:
[32524.386376]  #0:  (rtnl_mutex){+.+.+.}, at: [<ffffffff81431d42>] rtnl_lock+0x12/0x20
[32524.386387]  #1:  (&vlan_netdev_addr_lock_key/1){+.....}, at: [<ffffffff8141af83>] dev_set_rx_mode+0x23/0x40
[32524.386398]
[32524.386398] stack backtrace:
[32524.386403] CPU: 1 PID: 3103 Comm: ifconfig Tainted: G           O 3.14.0-rc2-0.7-default+ #35
[32524.386409] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[32524.386414]  ffffffff81ffae40 ffff8800d9625ae8 ffffffff814f68a2 ffff8800d9625bc8
[32524.386421]  ffffffff810a35fb ffff8800d8a8d9d0 00000000d9625b28 ffff8800d8a8e5d0
[32524.386428]  000003cc00000000 0000000000000002 ffff8800d8a8e5f8 0000000000000000
[32524.386435] Call Trace:
[32524.386441]  [<ffffffff814f68a2>] dump_stack+0x6a/0x78
[32524.386448]  [<ffffffff810a35fb>] __lock_acquire+0x7ab/0x1940
[32524.386454]  [<ffffffff810a323a>] ? __lock_acquire+0x3ea/0x1940
[32524.386459]  [<ffffffff810a4874>] lock_acquire+0xe4/0x110
[32524.386464]  [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386471]  [<ffffffff814fc07a>] _raw_spin_lock_nested+0x2a/0x40
[32524.386476]  [<ffffffff814275f4>] ? dev_mc_sync+0x64/0xb0
[32524.386481]  [<ffffffff814275f4>] dev_mc_sync+0x64/0xb0
[32524.386489]  [<ffffffffa0500cab>] vlan_dev_set_rx_mode+0x2b/0x50 [8021q]
[32524.386495]  [<ffffffff8141addf>] __dev_set_rx_mode+0x5f/0xb0
[32524.386500]  [<ffffffff8141af8b>] dev_set_rx_mode+0x2b/0x40
[32524.386506]  [<ffffffff8141b3cf>] __dev_open+0xef/0x150
[32524.386511]  [<ffffffff8141b177>] __dev_change_flags+0xa7/0x190
[32524.386516]  [<ffffffff8141b292>] dev_change_flags+0x32/0x80
[32524.386524]  [<ffffffff8149ca56>] devinet_ioctl+0x7d6/0x830
[32524.386532]  [<ffffffff81437b0b>] ? dev_ioctl+0x34b/0x660
[32524.386540]  [<ffffffff814a05b0>] inet_ioctl+0x80/0xa0
[32524.386550]  [<ffffffff8140199d>] sock_do_ioctl+0x2d/0x60
[32524.386558]  [<ffffffff81401a52>] sock_ioctl+0x82/0x2a0
[32524.386568]  [<ffffffff811a7123>] do_vfs_ioctl+0x93/0x590
[32524.386578]  [<ffffffff811b2705>] ? rcu_read_lock_held+0x45/0x50
[32524.386586]  [<ffffffff811b39e5>] ? __fget_light+0x105/0x110
[32524.386594]  [<ffffffff811a76b1>] SyS_ioctl+0x91/0xb0
[32524.386604]  [<ffffffff815057e2>] system_call_fastpath+0x16/0x1b

========================================================================

The reason is that all of the addr_lock_key for vlan dev have the same class,
so if we change the status for vlan dev, the vlan dev and its real dev will
hold the same class of addr_lock_key together, so the warning happened.

we should distinguish the lock depth for vlan dev and its real dev.

v1->v2: Convert the vlan_netdev_addr_lock_key to an array of eight elements, which
	could support to add 8 vlan id on a same vlan dev, I think it is enough for current
	scene, because a netdev's name is limited to IFNAMSIZ which could not hold 8 vlan id,
	and the vlan dev would not meet the same class key with its real dev.

	The new function vlan_dev_get_lockdep_subkey() will return the subkey and make the vlan
	dev could get a suitable class key.

v2->v3: According David's suggestion, I use the subclass to distinguish the lock key for vlan dev
	and its real dev, but it make no sense, because the difference for subclass in the
	lock_class_key doesn't mean that the difference class for lock_key, so I use lock_depth
	to distinguish the different depth for every vlan dev, the same depth of the vlan dev
	could have the same lock_class_key, I import the MAX_LOCK_DEPTH from the include/linux/sched.h,
	I think it is enough here, the lockdep should never exceed that value.

v3->v4: Add a huge array of locking keys will waste static kernel memory and is not a appropriate method,
	we could use _nested() variants to fix the problem, calculate the depth for every vlan dev,
	and use the depth as the subclass for addr_lock_key.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The gfp parameter was added in:
commit 47be03a2
Author: Amerigo Wang <amwang@redhat.com>
Date:   Fri Aug 10 01:24:37 2012 +0000

    netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()

    slave_enable_netpoll() and __netpoll_setup() may be called
    with read_lock() held, so should use GFP_ATOMIC to allocate
    memory. Eric suggested to pass gfp flags to __netpoll_setup().

    Cc: Eric Dumazet <eric.dumazet@gmail.com>
    Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NCong Wang <amwang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reason for the gfp parameter was removed in:
commit c4cdef9b
Author: dingtianhong <dingtianhong@huawei.com>
Date:   Tue Jul 23 15:25:27 2013 +0800

    bonding: don't call slave_xxx_netpoll under spinlocks

    The slave_xxx_netpoll will call synchronize_rcu_bh(),
    so the function may schedule and sleep, it should't be
    called under spinlocks.

    bond_netpoll_setup() and bond_netpoll_cleanup() are always
    protected by rtnl lock, it is no need to take the read lock,
    as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
    Cc: Jay Vosburgh <fubar@us.ibm.com>
    Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some drivers incorrectly assign vlan acceleration features to
vlan_features thus causing issues for Q-in-Q vlan configurations.
Warn the user of such cases.
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, if the card supports CTAG acceleration we do not
account for the vlan header even if we are configuring an
8021AD vlan.  This may not be best since we'll do software
tagging for 8021AD which will cause data copy on skb head expansion
Configure the length based on available hw offload capabilities and
vlan protocol.

CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: NVlad Yasevich <vyasevic@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vlan support 2 proto: 802.1q and 802.1ad, so make a new function
called vlan_dev_vlan_proto() which could return the vlan proto for
input dev.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the bh safe variant with the hard irq safe variant.

We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.

Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With TX VLAN offload enabled the source MAC address for frames sent using the
VLAN interface is currently set to the address of the real interface. This is
wrong since the VLAN interface may be configured with a different address.

The bug was introduced in commit 2205369a
("vlan: Fix header ops passthru when doing TX VLAN offload.").

This patch sets the source address before calling the create function of the
real interface.
Signed-off-by: NPeter Boström <peter.bostrom@netrounds.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ether_addr_equal_64bits is more efficient than ether_addr_equal, and
can be used when each argument is an array within a structure that
contains at least two bytes of data beyond the array, so it is safe
to use it for vlan, and make sense for fast path.

Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According Joe's suggestion, maybe it'd be faster to add an unlikely to
the test for PCKET_OTHERHOST, so I add it and see whether the performance
could be better, although the differences is so small and negligible, but
it is hard to catch that any lower device would set the skb type to
PACKET_OTHERHOST, so most of time, I think it make sense to add unlikely
for the test.

Cc: Joe Perches <joe@perches.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use ether_addr_copy instead of memcpy(a, b, ETH_ALEN) to
save some cycles on arm and powerpc.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace deprecated 'vconfig' tool with 'ip' from 'iproute2'. Add
some beautifications like replacing 'ethernet' with 'Ethernet' and
removing unneeded spaces.
Signed-off-by: NYegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the vlan code detects that the real device can do TX VLAN offloads
in hardware, it tries to arrange for the real device's header_ops to
be invoked directly.

But it does so illegally, by simply hooking the real device's
header_ops up to the VLAN device.

This doesn't work because we will end up invoking a set of header_ops
routines which expect a device type which matches the real device, but
will see a VLAN device instead.

Fix this by providing a pass-thru set of header_ops which will arrange
to pass the proper real device instead.

To facilitate this add a dev_rebuild_header().  There are
implementations which provide a ->cache and ->create but not a
->rebuild (f.e. PLIP).  So we need a helper function just like
dev_hard_header() to avoid crashes.

Use this helper in the one existing place where the
header_ops->rebuild was being invoked, the neighbour code.

With lots of help from Florian Westphal.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is to avoid very silly Kconfig dependencies for modules
using this routine.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a method for read-only access to the vlan device egress mapping.

Do this by refactoring vlan_dev_get_egress_qos_mask() such that now it
receives as an argument the skb priority instead of pointer to the skb.

Such an access is needed for the IBoE stack where the control plane
goes through the network stack. This is an add-on step on top of commit
d4a96865 "net/route: export symbol ip_tos2prio" which allowed the RDMA-CM
to use ip_tos2prio.
Signed-off-by: NEyal Perry <eyalpe@mellanox.com>
Signed-off-by: NHadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to enable lockdep on seqcount/seqlock structures, we
must explicitly initialize any locks.

The u64_stats_sync structure, uses a seqcount, and thus we need
to introduce a u64_stats_init() function and use it to initialize
the structure.

This unfortunately adds a lot of fairly trivial initialization code
to a number of drivers. But the benefit of ensuring correctness makes
this worth while.

Because these changes are required for lockdep to be enabled, and the
changes are quite trivial, I've not yet split this patch out into 30-some
separate patches, as I figured it would be better to get the various
maintainers thoughts on how to best merge this change along with
the seqcount lockdep enablement.

Feedback would be appreciated!
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Acked-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NPeter Zijlstra <peterz@infradead.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: James Morris <jmorris@namei.org>
Cc: Jesse Gross <jesse@nicira.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Roger Luethi <rl@hellgate.ch>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Simon Horman <horms@verge.net.au>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Wensong Zhang <wensong@linux-vs.org>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/1381186321-4906-2-git-send-email-john.stultz@linaro.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>