This patch fixes reported problems when trying to add a 9th device into a
system.
Signed-off-by: NAlan McIvor <alan.mcivor@reveal.co.nz>
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Tuner refactoring broke support of tuners with LNA configurations 1 and 2
for both, analog TV and DVB-T.
Additionally, this patch initializes the saa713x gpios defined by the gpiomask
at driver init to avoid undefined stated at dvb.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

There are some restrictions:
- The 2nd DVB-S section will only work if the 1st is configured for DVB-S too.
  so "options saa7134-dvb use_frontend=0,1" won't work.
- Currently it is not possible to set the higher LNB supply voltages, so
  14V instead of 13V in the 2nd section.
- It is not possibe to turn off the 2nd LNB supply independently.
This comes from the problem that the 2nd section can't access the i2c interface
of the LNB supply chip.
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

In the case of an access error to the high latency registers of
the audio DSP, the interface needs to be cleared, otherwise a cascade
of errors occurs.

This patch is closely modeled after a proposal by Mirek Slugen
Signed-off-by: NHartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

drivers/media/video/bt8xx/bttv-cards.c:3030:38: warning: "/*" within comment
drivers/media/video/bt8xx/bttv-cards.c:3032:20: warning: "/*" within comment
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If left in blank, the driver will use value 0 (Temic PAL)
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Tuner addresses were incorrect. Fix the entries.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All standard related configuration is stored within
struct tda18271_std_map_item.  Pass a pointer to this
structure rather than its individual members.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Add attach-time parameter, "small_i2c" to limit i2c transfer size to write
at most 16 registers at a time during initialization.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

TUNER_PHILIPS_ATSC is an ambiguous name for a tuner.  Rename it to
TUNER_PHILIPS_FCV1236D to be more descriptive.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We currently do not have a method to enable instance staring if i2c adapter
is NULL, in the cases of dvb demods that write to the tuner directly using
calc_regs.  Prevent possible wrong instance sharing for these cases until
a better solution can be found.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

flags used for spinlocks don't need to be initialized, except where the
compiler has no way to see, that the spin_unlock_irqrestore is only called
if the spin_lock_irqsave has been called before. Local variable
initialization doesn't have to be protected.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

As reported by  Roel Kluin <12o3l@tiscali.nl>:
in drivers/media/radio/radio-sf16fmr2.c:319:

for (i = 0; i < ARRAY_SIZE(radio_qctrl); i++) {
	if ((fmr2->card_type != 11)
        	        && V4L2_CID_AUDIO_VOLUME)
	        radio_qctrl[i].step = 65535;
        ...

I don't understand this '&& V4L2_CID_AUDIO_VOLUME'

While fixing this issue, I've revisited the volume control code and fixed
CodingStyle on the changed procedures.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Make the dev member of the struct videobuf_queue of type "struct device *"
to avoid future problems. Also change the prototype of the
videobuf_queue_core_init() function.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

tuner-xc2028 needs to know when a DVB module is sharing the same analog tuner.
This is done by comparing a magic number that needs to be the same on analog
and on digital. To make easier, this magic number is a pointer to some data
struct.

With the previous code, two different pointers were using, causing a
miss-detection.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The dev element of the struct videobuf_queue is now of type struct device
implicitly. Fix left-over casts.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@pengutronix.de>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

logical-bitwise & confusion
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This board works only with non-mts firmware
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

TV reception ok. S-video and Composite not tested. Audio not tested.
IR not implemented yet.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
CC: Guennadi Liakhovetski <kernel@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Lacy <mauro@lacy.com.ar>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

I have what looks like a Geovision GV-600 (or 650) card. It has a large
chip in the middle labeled

CONEXANT
FUSION 878A
25878-13
E345881.1
0312 TAIWAN

It has an audio connector coming out from a chip labeled

ATMEL
0242
AT89C2051-24PI

It is identified as follows on my Debian GNU/Linux Etch (kernel 2.6.18)

...
01:0a.0 Multimedia video controller: Brooktree Corporation Bt878 Video Capture (rev 11)
01:0a.1 Multimedia controller: Brooktree Corporation Bt878 Audio Capture (rev 11)
...
01:0a.0 0400: 109e:036e (rev 11)
        Subsystem: 008a:763c
        Flags: bus master, medium devsel, latency 64, IRQ 58
        Memory at dfffe000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2

01:0a.1 0480: 109e:0878 (rev 11)
        Subsystem: 008a:763c
        Flags: bus master, medium devsel, latency 64, IRQ 58
        Memory at dffff000 (32-bit, prefetchable) [size=4K]
        Capabilities: [44] Vital Product Data
        Capabilities: [4c] Power Management version 2

It was being detected as a GENERIC UNKNOWN CARD both by the 2.6.18
kernel and the latest v4l-dvb drivers, but it did not work at all. The
card has sixteen (16) BNC video inputs, four of them on the board itself
and twelve on three daughter-cards. It has a single bt878 chip, no tuner
and what looks like and audio input. After doing some research I managed
to get only eight channels working by forcing card=125 and those DID NOT
match channels 0-7 on the card, and no audio.

Based on what was working for card=125, I added the card definition
block, added a specific muxsel routine and got the card working fully
with xawtv, where the sixteen channels show up as Composite0 to
Composite15, matching the channel labels in the card and daughter-cards.
I have made no efforts yet to get audio working, but would appreciate
any pointers.
Signed-off-by: NErnesto Hernández-Novich <emhn@usb.ve>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

poll_one allocated on stack struct poll_wqueues which is pretty big
structure (>500 bytes on x86_64). v4l1_compat_sync invokes poll_one
in a loop, so allocate struct poll_wqueues in v4l1_compat_sync (with
kmalloc) and pass it to poll_one.
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

v4l_compat_translate_ioctl used 1376 bytes of stack (x86_64),
so split this 800 lines long function into ~20 small noinline functions;
the biggest function takes now 712 bytes (v4l1_compat_sync)

fix VIDIOCSWIN handler which printked wrong errors
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

fix most coding style violations found by checkpatch
Signed-off-by: NMarcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

simple_dvb_configure returns the actual tuned frequency to its caller, so
it must be declared as a u32 rather than an int.  As a result, we will
return 0 to indicate a failure.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

taken from dvb-pll
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enable digital tuning support within tuner-simple. This will allow for a
single tuner module to manage the hardware, without having dvb-pll loaded.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>