Adding the PM configuration of PMC when the platform support suspend
function.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds "non-removable" property of MMC host where the eMMC device
is for Tegra platform.

And the "keep-power-in-suspend" property was used for the SDIO device that
need this to go into suspend mode (e.g. BRCM43xx series).
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Adding KBC as a wakeup source for Whistler board.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This adds the power gpio key to DT and enable the wakeup of the gpio key
for the device. The Seaboard and paz00 already had the power gpio key
binding and the power key of Whistler was on KBC. So these boards' device
tree didn't include in this patch.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Set "regulator-always-on" for the SD slot on Dalmore, so that SD cards
work. This used to work, since this regulator is on by default, but was
broken by commit "ARM: tegra: dalmore: add TPS65090 node", since that
didn't specify always-on for this regulator.

In the long run, the regulators should all be hooked up to the SDHCI
device nodes. However, we haven't done that for any of the Tegra boards
yet, so to be consistent, this patch simply forces the regulator on,
rather than hooking it up and making it work differently to other boards.
Reported-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Audio-related clocks need to be represented in the device tree. Update
bindings to describe which clocks are needed, and DT files to include
those clocks.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 reference platform Dalmore has voltage switch
regulators which are controlled by the Tegra GPIOs.

Add DT node for fixed regulators.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 reference platform, Dalmore, uses the TPS65090 as
secondary PMICs which is mainly act as voltage switch regulator
controlled by i2c communication.

Add DT node for TPS65090.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Dalmore uses the TPS51632 as CPU regulator. The device is connected
on I2C5.

Add DT node for TPS51632.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds the node for the bq20z45 I2C gas gauge which is
compatible with the sbs-battery power supply driver.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: remove unit-address from node name since it's unique already]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add documentation for device tree binding of NVIDIA's Tegra I2C
controller driver.

Describing all compatible values used for different Tegra SoCs
in details in this documentation.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed a couple typos, trimmed examples]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 6 SPI controllers. These controllers are
redesign on T114 with different register interface.

Add DT entry for spi controllers and make it compatible with
"nvidia,tegra114-spi", since they are a new incompatible design.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed reg property for 3rd SPI controller]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 SoCs have the matrix keyboard controller which
supports 11x8 type of matrix. The number of rows and columns
are configurable.

Add DT entry for KBC controller with compatibility as "nvidia,tegra114-kbc".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add APB DMA requestor and serial aliases for serial controller.
There are two serial drivers i.e. 8250 based simple serial driver
and APB DMA based serial driver for higher baudrate and performace.

The simple serial driver is selected by compatible value
"nvidia,tegra114-uart", "nvidia,tegra20-uart", and the APB DMA based
driver is selected by compatible value "nvidia,tegra114-hsuart",
"nvidia,tegra30-hsuart".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 5 I2C controllers. These controllers have the
following changes which makes incompatible with previous hardware:
- Single clock source to I2C controller.
- Interrupt support for per packet transfer.

Add DT entry for I2C controllers and make it compatible with
"nvidia,tegra114-i2c".
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed location of status property for consistency]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

NVIDIA's Tegra114 has 32 channels APB DMA controller. Add DT entry for
APB DMA controllers and make it compatible with "nvidia,tegra114-apbdma".

Tegra114 DMA controller is not compatible with Tegra30/Tegra20 DMA
controller driver as in Tegra114, the global pause also clock gate the
DMA register and hence it iw not possible to write the DMA register
with global pause.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
[swarren: fixed DT node order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds a device tree node for the four PWM controllers present
on Tegra114.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

We should be defining the PWM nodes with status as "disabled" in the
chip-specific dtsi file, since we don't know whether specific boards
will use the PWM or not. This patch fixes the PWM node status for
Tegra20 and Tegra30.

Also fixed the one user of PWM, which is the Tegra20 medcom-wide board,
so that PWM is set to "okay" in the board-specific dts file.
Signed-off-by: NAndrew Chew <achew@nvidia.com>
[swarren: in medcom-wide: fixed node sort order, removed duplicate pwm:
label, fixed syntax error]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Dalmore has a built-in eMMC device and a user-accessible SD card slot.
Add device tree nodes to enable these.

Based on changes by: Pritesh Raithatha <praithatha@nvidia.com>
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: added commit description, fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This patch adds in the SDHCI nodes for the busses supported on Tegra114
boards.
Signed-off-by: NPritesh Raithatha <praithatha@nvidia.com>
[Rhyland added clk refs to & reordered sdhci nodes and removed spaces]
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
[swarren: fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

This change adds the default pinctrl nodes for the Dalmore Tegra114
platform.
Signed-off-by: NPritesh Raithatha <praithatha@nvidia.com>
[Rhyland added patch description]
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
[swarren: fixed DT node sort order]
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The USB PHY nodes are all grouped together rather than being sorted based
on reg address like all other nodes fix this.

I apologize for the churn; I should have noticed this during review of the
patches that caused this.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Remove white-space from empty line; triggers checkpatch.
Signed-off-by: NStephen Warren <swarren@nvidia.com>

A gap exists in the binding's clock ID definitions. Fix the clock driver
to be consistent. This allows pclk to be looked up through device tree
and prevents:

ERROR: could not get clock /pmc:pclk(0)
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The UART driver enables the console uart clock, so we don't need to do that
anymore in this file.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Add references to tegra_car clocks for the basic device nodes. Also remove
the clock-frequency property of the serial node as the UART driver can now
use the clock framework to obtain the frequency.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Implement clocks for Tegra114.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The device tree binding models Tegra114 CAR (Clock And Reset) as a single
monolithic clock provider.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Workaround a hardware bug in MSENC during clock enable.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

We will need some tegra peripheral clocks with the CLK_IGNORE_UNUSED flag,
most notably mselect, which is a bridge between AXI and most peripherals.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra114 introduces new PLL types. This requires new clocktypes as well
as some new fields in the pll structure.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

PLLC2 and PLLC3 on Tegra114 have separate phaselock and frequencylock bits.
So switch to a lock mask to be able to test both at the same time.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Some PLLs in Tegra114 don't use a power of 2 mapping for the post divider.
Introduce a table based approach and switch PLLU to it.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra114 PLLC2 and PLLC3 don't have a lock enable bit. The lock bits are
always functional.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Not all PLLs in Tegra114 have a bypass bit. Adapt the common code to only use
this bit when available.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Refactor the PLL programming code to make it useable by the new PLL types
introduced by Tegra114.

The following changes were done:

* Split programming the PLL into updating m,n,p and updating cpcon
* Move locking from _update_pll_cpcon() to clk_pll_set_rate()
* Introduce _get_pll_mnp() helper
* Move check for identical m,n,p values to clk_pll_set_rate()
* struct tegra_clk_pll_freq_table will always contain the values as defined
  by the hardware.
* Simplify the arguments to clk_pll_wait_for_lock()
* Split _tegra_clk_register_pll()
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

tegra_boot_secondary() relies on some of the car ops. This means having an
uninitialized tegra_cpu_car_ops will lead to an early boot panic.
Providing a dummy struct avoids this and makes adding Tegra114 clock support
in a bisectable way a lot easier.
Signed-off-by: NPeter De Schrijver <pdeschrijver@nvidia.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

The Tegra clock driver is initialized during the ARM machine descriptor's
.init_irq() hook. It can't be initialized earlier, since dynamic memory
usage is required. It can't be initialized later, since the .init_timer()
hook needs the clocks initialized. However, at this time, udelay()
doesn't work.

The Tegra clock initialization table may enable some PLLs. Enabling a PLL
may require usage of udelay(). Hence, this can't happen right when the
clock driver is initialized.

To solve this, separate the clock driver initialization from the clock
table processing, so they can execute at separate times.
Signed-off-by: NStephen Warren <swarren@nvidia.com>