to reset the TSF, AR5K_BEACON_RESET_TSF has to be 1, not 0. also we have a
function for that so use it.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when using a fixed antenna we should use the antenna number in all tx
descriptors, otherwise the hardware will sometimes send the frame out on the
other antenna. it seems like the hardware does not always respect the default
antenna and diversity settings (esp.  AR5K_STA_ID1_DEFAULT_ANTENNA).

also i would like to note that antenna diversity does not always work correctly
on 5414 (at least) when only one antenna is connected: for example all frames
might be received on antenna A but still the HW tries to send on antenna B some
times, causing packet loss.

this is both verified with the antenna statistics output of the previous patch
and a spectrum analyzer.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ieee->networks consists of 128 struct libipw_network entries. If
we allocate this chunk of memory altogether, it ends up with an
order 4 page allocation. High order page allocation is likely to fail
on system high load. This patch splits the big chunk memory allocation
into small pieces, each is 344 bytes, allocates them with 128 times.

The patch fixed bug http://bugzilla.kernel.org/show_bug.cgi?id=14989Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit 34e89507 introduced sta_mtx
locking into sta_info_insert() (now sta_info_insert_rcu), but forgot
to unlock this mutex on one of the error paths. Fix this by adding
the missing mutex_unlock() call for the case where STA insert fails
due to an entry existing already. This may happen at least in AP mode
when a STA roams between two BSSes (vifs).
Signed-off-by: NJouni Malinen <j@w1.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the KSEG1ADDR define from rt2x00soc.h as it redefines and covers the
correct one from the arch/mips/include/asm/addrspace.h. Otherwise the driver
oopses on the target platform (Ralink rt3050 board).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Port commit 20deb48d16fdd07ce2fdc8d03ea317362217e085
from git://tipc.cslab.ericsson.net/pub/git/people/allan/tipc.git

Part of the large effort I'm trying to help with getting all the downstreamed
code from windriver forward ported to the upstream tree

Origional commit message
Restore check to filter out inadverdently received messages
This patch reimplements a check that allows TIPC to discard messages
that are not intended for it.  This check was present in TIPC 1.5/1.6,
but was removed by accident during the development of TIPC 1.7; it has
now been updated to account for new features present in TIPC 1.7 and
reinserted into TIPC.  The main benefit of this check is to filter
out messages arriving from orphaned link endpoints, which can arise
when a node exits the network and then re-enters it with a different
TIPC network address (i.e. <Z.C.N> value).
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Origionally-authored-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove htohl implementation from tipc

I was working on forward porting the downstream commits for TIPC and ran accross this one:
http://tipc.cslab.ericsson.net/cgi-bin/gitweb.cgi?p=people/allan/tipc.git;a=commitdiff;h=894279b9437b63cbb02405ad5b8e033b51e4e31e

I was going to just take it, when I looked closer and noted what it was doing.
This is basically a routine to byte swap fields of data in sent/received packets
for tipc, dependent upon the receivers guessed endianness of the peer when a
connection is established.  Asside from just seeming silly to me, it appears to
violate the latest RFC draft for tipc:
http://tipc.sourceforge.net/doc/draft-spec-tipc-02.txt
Which, according to section 4.2 and 4.3.3, requires that all fields of all
commands be sent in network byte order.  So instead of just taking this patch,
instead I'm removing the htohl function and replacing the calls with calls to
ntohl in the rx path and htonl in the send path.

As part of this fix, I'm also changing the subscr_cancel function, which
searches the list of subscribers, using a memcmp of the entire subscriber list,
for the entry to tear down.  unfortunately it memcmps the entire tipc_subscr
structure which has several bits that are private to the local side, so nothing
will ever match.  section 5.2 of the draft spec indicates the <type,upper,lower>
tuple should uniquely identify a subscriber, so convert subscr_cancel to just
match on those fields (properly endian swapped).

I've tested this using the tipc test suite, and its passed without issue.
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use self documenting noinline_for_stack instead of duplicated comments.
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

(Applies on top of "Remove uses of NIPQUAD, use %pI4")

Casts to void of snprintf are most uncommon in kernel source.
9 use casts, 1301 do not.

Remove the remaining uses in net/sunrpc/
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Originally submitted Jan 1, 2010
http://patchwork.kernel.org/patch/71221/

Convert NIPQUAD to the %pI4 format extension where possible
Convert %02x%02x%02x%02x/NIPQUAD to %08x/ntohl
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Looks like commit a6e4bc53 didn't include updates to drivers so the
Blackfin CAN driver fails to build now.
Signed-off-by: NBarry Song <barry.song@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 4957faad (TCPCT part 1g: Responder Cookie => Initiator), part
of TCP_COOKIE_TRANSACTION implementation, forgot to correctly size
synack skb in case user data must be included.

Many thanks to Mika Pentillä for spotting this error.
Reported-by: NPenttillä Mika <mika.penttila@ixonos.com>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We added an automatic route cache rebuilding in commit 1080d709
but had to correct few bugs. One of the assumption of original patch,
was that entries where kept sorted in a given way.

This assumption is known to be wrong (commit 1ddbcb00 gave an
explanation of this and corrected a leak) and expensive to respect.

Paweł Staszewski reported to me one of his machine got its routing cache
disabled after few messages like :

[ 2677.850065] Route hash chain too long!
[ 2677.850080] Adjust your secret_interval!
[82839.662993] Route hash chain too long!
[82839.662996] Adjust your secret_interval!
[155843.731650] Route hash chain too long!
[155843.731664] Adjust your secret_interval!
[155843.811881] Route hash chain too long!
[155843.811891] Adjust your secret_interval!
[155843.858209] vlan0811: 5 rebuilds is over limit, route caching
disabled
[155843.858212] Route hash chain too long!
[155843.858213] Adjust your secret_interval!

This is because rt_intern_hash() might be fooled when computing a chain
length, because multiple entries with same keys can differ because of
TOS (or mark/oif) bits.

In the rare case the fast algorithm see a too long chain, and before
taking expensive path, we call a helper function in order to not count
duplicates of same routes, that only differ with tos/mark/oif bits. This
helper works with data already in cpu cache and is not be very
expensive, despite its O(N^2) implementation.

Paweł Staszewski sucessfully tested this patch on his loaded router.
Reported-and-tested-by: NPaweł Staszewski <pstaszewski@itcare.pl>
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bios sub version from unified fw image is calculated incorrect.
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Validate all sections of unified fw image, before accessing them,
to avoid seg fault.
Signed-off-by: NSucheta Chakraborty <sucheta@dut6195.unminc.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For promiscuous mode, driver send request to device for deleting
multicast addresses and again it send request for adding them back
while exiting from this mode, this is bad for performance.
Just setting device in promiscuous mode is enough, no need to del/add
multicast addresses.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Statistics added for lro/lso bytes, count for tx stop queue and
wake queue and skb alloc failure count.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Kernel default tx csum function (ethtool_op_get_tx_csum) doesn't show
correct csum status. It takes various FLAGS (NETIF_F_ALL_CSUM) in account
to show tx csum status, which driver doesn't set while disabling tx csum.
Signed-off-by: NSucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: NAmit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch cleans up some unused code from be_load_fw().
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PCI functions are virtuialized in applications by assigning PCI
functions to VM (PCI passthrough), the be2net driver in the VM sees a

different function number. So, use of PCI function number in any
calculation will break existing code. This patch takes care of it.
Signed-off-by: NAjit Khaparde <ajitk@serverengines.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 6b03a53a (tcp: use limited socket backlog) added the possibility
of dropping frames when backlog queue is full.

Commit d218d111 (tcp: Generalized TTL Security Mechanism) added the
possibility of dropping frames when TTL is under a given limit.

This patch adds new SNMP MIB entries, named TCPBacklogDrop and
TCPMinTTLDrop, published in /proc/net/netstat in TcpExt: line

netstat -s | egrep "TCPBacklogDrop|TCPMinTTLDrop"
    TCPBacklogDrop: 0
    TCPMinTTLDrop: 0
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the "__must_check" tag to sk_add_backlog() so that any failure to
check and drop packets will be warned about.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to Paul McKenny for pointing out that it is incorrect to use
synchronize_rcu_bh to ensure that pending callbacks have completed.
Instead we should use rcu_barrier_bh.
Reported-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As Paul McKenney correctly pointed out, __br_mdb_ip_get needs
to use the RCU list walking primitive in order to work correctly
on platforms where data-dependency ordering is not guaranteed.
Reported-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPV6_PREFER_SRC_xxx definitions:
| #define IPV6_PREFER_SRC_TMP             0x0001
| #define IPV6_PREFER_SRC_PUBLIC          0x0002
| #define IPV6_PREFER_SRC_COA             0x0004

RT6_LOOKUP_F_xxx definitions:
| #define RT6_LOOKUP_F_SRCPREF_TMP        0x00000008
| #define RT6_LOOKUP_F_SRCPREF_PUBLIC     0x00000010
| #define RT6_LOOKUP_F_SRCPREF_COA        0x00000020

So, we can translate between these two groups by shift operation
instead of multiple 'if's.
Signed-off-by: NYOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we were unable to detect a PHY on any of the MDIO bus id we tried instead of
bailing out with -ENODEV, assume the MAC is connected to a switch and use MDIO
bus 0. This unbreaks quite a lot of devices out there whose switch cannot be
detected.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Despite what the comment above CPMAC_SKB_SIZE says, the hardware also
needs to account for the FCS length in a received frame. This patch fix
the receiving of 802.1q frames which have 4 more bytes. While at it
unhardcode the definition and use the one from if_vlan.h.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update the CAN Maintainer responsibilities and add source paths.
Additional the SocketCAN core ML is not subscribers-only anymore.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This one removes trailing whitespace in pegasus.h and more importantly
adds new Pegasus compatible device.
Signed-off-by: NJulian Brown <julian@codesourcery.com>
Signed-off-by: NPetko Manolov <petkan@nucleusys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the call to kcalloc() fails then we should return -ENOMEM.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We test that "prot->rsk_prot" is non-null right before we dereference it
on this line.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"skb" is alway non-null here, but even if it were null the check isn't
needed because dev_kfree_skb() can handle it.

This eliminates a smatch warning about dereferencing a variable before
checking that it is non-null.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We dereference "port" on the lines immediately before and immediately
after the test so port should hopefully never be null here.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fix a race at the end of NAPI processing in ks8695_poll() function.
Signed-off-by: NFigo.zhang <figo1802@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently s2io is dumping debug messages using the interface name
before it was allocated, showing a message like the following:

s2io: eth%d: Ring Mem PHY: 0x7ef80000
s2io: s2io_reset: Resetting XFrame card eth%d

This patch just fixes it, printing the pci bus information for
the card instead of the interface name.
Signed-off-by: NBreno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

when receiving a particular type of NFS v2 UDP traffic, the hardware could
DMA some bad data and then hang, possibly corrupting memory.

Disable the NFS parsing in this hardware, verified to fix the bug.

Originally reported and reproduced by RedHat's Neil Horman
CC: nhorman@tuxdriver.com
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The typhoon driver was incorrectly using smp_wmb() to order memory
accesses against IO to the NIC in a few instances. Use wmb() instead,
which is required to actually order between memory types.
Signed-off-by: NDavid Dillow <dave@thedillows.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>