Fixes:
/git/arm-soc/drivers/mmc/host/sdhci.c: In function 'sdhci_add_host':
/git/arm-soc/drivers/mmc/host/sdhci.c:2910:19: warning: ignoring
return value of 'regulator_enable', declared with attribute
warn_unused_result [-Wunused-result]
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Used resource_size function instead of explicit computation.
Patch found using coccinelle.
Signed-off-by: NAlexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The variable 'mmc' is initialized but never used, so remove it.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes timeout problems on t4240's sdhci controller:

	mmc0: Too large timeout requested for CMD25!
	mmc0: Too large timeout requested for CMD25!
	mmc0: Too large timeout requested for CMD25!
Signed-off-by: NChunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

For some Realtek card readers, the power up sequence can only be executed
when power has been turned off fully.

So the rtsx host should not start power up sequence again when set_ios
been called if the power has been turned on.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

With device core now able to setup the default pin configuration,
the call to devm_pinctrl_get_select_default can be removed. And
the pin configuration code based on the deprecated Samsung specific
gpio bindings is also removed.
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch uses module_platform_driver_probe() macro which makes
the code smaller and simpler.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

ACPI spec 5 defined the _ADR encoding for sdio bus as:
High word - slot number (0 based)
Low word  - function number

This patch adds support for binding sdio function device with acpi node,
and if successful, involve acpi into its power management.
Signed-off-by: NAaron Lu <aaron.lu@intel.com>
Reviewed-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

1. mmc_rescan will call get_cd to know whether the card is present
before mmc_rescan_try_freq to avoid useless trials during
card removal or start host is called when card is not present.

2. get_cd needs to be checked to resolve slow card removal issue.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Function _mmc_detect_card_removed will be called to know whether
the card is still present when host->bus_ops->detect is called.
In current code, the return value of this function generally only
depend on the result of sending cmd13 to card, which may not safe
for card with detection support like slot gpio detection.
Because the communication status between host and card may out of
sync with the detect status if remove the card slowly or hands shake
during the process. The direct reason is the async between card
detect switch and card/slot pad contaction in hardware, which is
defined by spec.

The spec define card insert/remove sequence as below (both standard size
SD card and MicroSD card have the same sequence):
"Part 1 Standard Size SD Card Mechanical Addendum Ver4.00 Final,
Appendix C: Card Detection Switch" (Take normally open type as example)
a)SD card insertion sequence:
  The card detection switch should be turned on after all SD card
  contact pads are connected to the host connector contact pads.
b)SD removal sequence:
  The card detection switch should be turned off when the SD card
  is just going to be removed and before any SD card contact pad is
  disconnected from the host connector contact pad.

Below is the sequence when this issue occur (Take slot gpio detection
as example and remove the card slowly during the process):
1. gpio level changed and card detect interrupt triggered.
2. mmc_rescan was launched.
3. the card pads were still contacted with the slot pads because of slow
   removal. So _mmc_detect_card_removed and mmc_rescan think card was
   still present (cmd13 succeed).
4. card pads were discontacted from the card slot pads.
So the card was actually removed finally but the card removal event
has been missed by system.
The interval length between step 1 and step 4 depends on the
card removal speed. If it's longer than the detect work schedule
delay which is 200ms, this issue will likely happen.

This patch add the card detect status check in function
_mmc_detect_card_removed if cmd13 check succeed and host->ops->get_cd
provided. If get_cd detect no card present then schedule another detect
work 200ms later.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Tested-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Reviewed-by: NPhilip Rakity <prakity@nvidia.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The JEDEC MMC v4 spec defines a new PRV value in place of the original
fwrev and hwrev specified in v1. We can expose this in the kernel to enable
user space to more easily determine the product revision of a given MMC.
Signed-off-by: NBernie Thompson <bhthompson@chromium.org>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

Do not return probe failure with missing DMA resources, allow driver
to work in PIO mode.  Tested on da850-evm by mounting partition
followed by file creation and deletion.
Signed-off-by: NManjunathappa, Prakash <prakash.pm@ti.com>
Tested-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In the legacy code, driver clear not only UHS_REG 16 bit also 0-15bit.
If we use UHS-1 mode spec card like SDR50, SDR104. UHS_REG 0-15 should
be set by 1 according to slot id. In this case, legacy code can cause
problems.

In particular, UHS_REG consists of DDR_REG[31:16] and VOLT_REG[15:0].
Before adjusting this patch, bit[15:0] is always cleared.
Signed-off-by: NHyeonsu Kim <hyeonsu.kim@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

In dwc manual, the below contents are described:

"During end of packet, interrupt is not generated if threshold
programming is larger than any remaining data. It is responsibility
of host to read remaining bytes on seeing Data Transfer Done
interrupt"

We also have seen the data cannot be read fully when
"sg_miter->length" is less than FIFO size.
Signed-off-by: NKyoungil Kim <ki0351.kim@samsung.com>
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Check the result of mmc_add_host() and return the value.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use devm_clk_get() rather than clk_get() to make cleanup paths
more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If the CD/WP-GPIOs are not provided by the SoC's GPIO controller,
we need to handle the case where omap_hsmmc is probed earlier than
the GPIO controller chosen in the device tree.

Fix this by checking the return value of of_get_named_gpio against
-EPROBE_DEFER and passing it through to the probe function.
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Acked-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Updating the sdhci-tegra driver to use mmc_of_parse to support standard
MMC DT bindings. Then we can remove the redundant code that already support
in generic MMC core.
Signed-off-by: NJoseph Lo <josephl@nvidia.com>
Tested-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Silences the following sparse warning:
drivers/mmc/host/dw_mmc-exynos.c:218:5: warning:
symbol 'dw_mci_exynos_probe' was not declared. Should it be static?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Acked-by: NSeungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The mmc controller on Tegra114 platforms is basically compatible with
the settings used for Tegra30. However there is a difference where we
don't need the extra ENABLE_SDHCI_SPEC_300 quirk as Tegra114 hardware
advertises v3.0 support already.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The structs wrapped with the SOC ifdefs are small enough where having
them always there shouldn't be a big overhead. Removing the ifdefs
also makes the code a little cleaner.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Convert to the much saner new idr interface.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For better code reuse use the newly added page iterator to iterate
through the pages.  The offset, length within the page is still
calculated by the mapping iterator as well as the actual mapping.  Idea
from Tejun Heo.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use managed allocations to get memory, clock and interrupts . This
significantly simplifies clean up paths.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use mmc_of_parse() to get interface capability flags and used GPIOs from
device-tree bindings.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:

drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]

Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK does basically the same as
implementing struct sdhci_ops .get_timeout_clock, so simply set that
quirk and remove the custom code to simplify the driver.
Reported-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch supports packed write command of eMMC4.5 devices.  Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally.  As a result, packed command help
write throughput be improved.  The following tables show the results
of packed write.

Type A:
test     none |  packed
iozone   25.8 |  31
tiotest  27.6 |  31.2
lmdd     31.2 |  35.4

Type B:
test     none |  packed
iozone   44.1 |  51.1
tiotest  47.9 |  52.5
lmdd     51.6 |  59.2

Type C:
test     none |  packed
iozone   19.5 |  32
tiotest  19.9 |  34.5
lmdd     22.8 |  40.7
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Reviewed-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).

This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>