Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This is essentially the code that was factored out into the core when the
feature was implemented.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is very common for regulators to support having their enable signal
controlled by a GPIO. Since there are a bunch of fiddly things to get
right like handling the operations when the enable signal is tied to
a rail and it's just replicated code add support for this to the core.

Drivers should set ena_gpio in their config if they have a GPIO control,
using ena_gpio_flags to specify any flags (including GPIOF_OUT_INIT_ for
the initial state) and ena_gpio_invert if the GPIO is active low. The
core will then override any enable and disable operations the driver has
and instead control the specified GPIO.

This will in the future also allow us to further extend the core by
identifying when several enable signals have been tied together and
handling this properly.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Create new _regulator_do_enable() and _regulator_do_disable() operations
which deal with the mechanics of performing the enable and disable, partly
to cut down on the levels of indentation and partly to support some future
work.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Many regulators have a fixed specification for their enable time. Allow
this to be set in the regulator_desc as a number to save them having to
implement an explicit operation.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Match the device's regulators with the property of
"regulator-compatible" of each regulator node.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Acked-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It is ok to request voltage with min_uV < tps->info[rid]->min_uV and
max_uV > tps->info[rid]->max_uV.

The equation we used in uv_to_vsel() does not allow
min_uV < tps->info[rid]->min_uV, otherwise it returns negative selector.
So we need to set min_uV = tps->info[rid]->min_uV if
min_uV < tps->info[rid]->min_uV.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This permits the setting of bogus values because the invalidity check is
itself invalid.

Reported-by: dcb314@hotmail.com
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch refactors the code to get rid of the fixed_ilimsel and FIXED_ILIMSEL
flag usage, and convert all the fixed ilimsel to table based (with one entry in
the table).

We can differentiate fixed ilimsel by checking info->n_ilimsels == 1,
thus FIXED_ILIMSEL flag can be removed.

This change makes the logic of the code simpler as all the ilimsels are table
based now.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch adds fixed_5000000_voltage table for fixed voltage,
so we can convert regulator_ops to regulator_list_voltage_table.

We can differentiate fixed voltage by checking rdev->desc->n_voltages == 1,
thus remove the FIXED_VOLTAGE flag usage.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

of_get_named_gpio() needs the driver hosting the GPIO that the DT
property references to have been probed. Detect this specific failure,
and defer the probe of the whole regulator until this API can complete.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Convert tps65217_pmic_ldo1_ops to use regulator_list_voltage_table.

We have n_voltages and volt_table settings in regulator_desc,
so we don't need the table and table_len fields in struct tps_info.
Thus remove them from struct tps_info.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

The acpi_pad driver can get stuck in destroy_power_saving_task()
waiting for kthread_stop() to stop a power_saving thread.  The problem
is that the isolated_cpus_lock mutex is owned when
destroy_power_saving_task() calls kthread_stop(), which waits for a
power_saving thread to end, and the power_saving thread tries to
acquire the isolated_cpus_lock when it calls round_robin_cpu().  This
patch fixes the issue by making round_robin_cpu() use its own mutex.

https://bugzilla.kernel.org/show_bug.cgi?id=42981

Cc: stable@vger.kernel.org
Signed-off-by: NStuart Hayes <Stuart_Hayes@Dell.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This fixes a regression in 3.4-rc1 caused by commit
ea9f8856
(ACPI video: Harden video bus adding.)

Some platforms don't have _DOS control method, but the ACPI
backlight still works.
We should not invoke _DOS for these platforms.

https://bugzilla.kernel.org/show_bug.cgi?id=43168

Cc: Igor Murzov <intergalactic.anonymous@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

In commit 7a879824 we added
a wrapper for the WDIOC_GETSTATUS ioctl call. The code results
however in a different behaviour: it returns an error if the
driver doesn't support the status operation. This is not
according to the API that says that when we don't support
the status operation, that we just should return a 0 value.
Only when the device isn't there anymore, we should return an
error.
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This patch is to unregister for NMI events upon exit. Also we are now
making the default setting for allow_kdump enabled.
Signed-off-by: NThomas Mingarelli <thomas.mingarelli@hp.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

The recent conversion of iTCO_wdt resulted in the driver no longer
getting loaded automatically, since it no longer has a
MODULE_DEVICE_TABLE() included. As the lpc_ich driver now creates a
platform device, auto-loading can easily be done by having a respective
module alias in place.
Signed-off-by: NJan Beulich <jbeulich@suse.com>
Cc: Aaron Sierra <asierra@xes-inc.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NWim Van Sebroeck <wim@iguana.be>

This reverts commit f82cfb6b.

This breaks the backlight controls on my IVB asus zenbook with an eDP
panel.

I guess the right fix would be to read this bit and use either the pch
or the cpu register to frob the backlight values. But that is stuff
for -next.

Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Commit e978aa7d ( cpuidle: Move
dev->last_residency update to driver enter routine; remove dev->last_state)
was  breaking suspend on laptops, as reported in the below link
	- https://lkml.org/lkml/2011/11/11/164

This was fixed in commit 3439a8da
(ACPI / cpuidle: Remove acpi_idle_suspend (to fix suspend regression)
by removing acpi_idle_suspend flag.
	- https://lkml.org/lkml/2011/11/14/74

But this did fix did not work on all systems
as Suspend/resume regression was reported on Lenovo S10-3
recently by Dave.
	- https://lkml.org/lkml/2012/5/27/115
It looked like with commit e978aa7d broke suspend and
with commit 3439a8da resume was not working with acpi_idle driver.

This patch fixes the regression that caused this issue
in the first place. acpi_idle_suspend flag is essential on
some x86 systems to prevent the cpus from going to deeper C-states
when suspend is triggered ( commit b04e7bdb )
So reverting the commit 3439a8da is essential.

By default, irqs are disabled in cpu_idle arch specific call
and re-enabled in idle state return path . During suspend,
the acpi_idle_suspend flag is set, which
prevents the cpus from going to deeper idle states,
it is essential to enabling the irqs in this return path too.

To address the suspend issue,
we were not re-enabling the interrupts while returning from
acpi_idle_enter_bm() routine if acpi_idle_suspend flag is set.
and this caused suspend failure.

In addition to the above, to improve the readability of the code,
return of -ENIVAL is replaced with -EBUSY in acpi_idle_suspend
return path. Implying that the system is currently busy when suspend
is in progress, which prevents the cpus from entering deeper C-states.
Reported-and-Tested-by: NDav Hansen <dave@linux.vnet.ibm.com>
Tested-by: NPreeti Murthy <preeti@linux.vnet.ibm.com>
Signed-off-by: NDeepthi Dharwar <deepthi@linux.vnet.ibm.com>
Reviewed-by: NSrivatsa S Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

Commit "e9b4cf20 UBI: fix debugfs-less systems support" fixed one
regression but introduced a different regression - the debugfs is now always
compiled out. Root cause: IS_ENABLED() arguments should be used with the
CONFIG_* prefix.
Signed-off-by: NBrian Norris <computersforpeace@gmail.com>
Signed-off-by: NArtem Bityutskiy <artem.bityutskiy@linux.intel.com>

The freescale arm i.MX series platform can support this driver, and
usually the arm cpu works in the little endian mode by default, while
device tree entry value is stored in big endian format, we should use
be32_to_cpup() to handle them, after modification, it can work well
both on the le cpu and be cpu.

Cc: stable <stable@vger.kernel.org> # v3.2+
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: NHui Wang <jason77.wang@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Just forgot this when I posted it, and yes I'm the only person
to have changed the file since.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes:
[   15.470311] WARNING: at /local/scratch/ianc/devel/kernels/linux/fs/sysfs/file.c:498 sysfs_attr_ns+0x95/0xa0()
[   15.470326] sysfs: kobject eth0 without dirent
[   15.470333] Modules linked in:
[   15.470342] Pid: 12, comm: xenwatch Not tainted 3.4.0-x86_32p-xenU #93
and
[    9.150554] BUG: unable to handle kernel paging request at 2b359000
[    9.150577] IP: [<c1279561>] linkwatch_do_dev+0x81/0xc0
[    9.150592] *pdpt = 000000002c3c9027 *pde = 0000000000000000
[    9.150604] Oops: 0002 [#1] SMP
[    9.150613] Modules linked in:

This is http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=675190Reported-by: NGeorge Shuklin <george.shuklin@gmail.com>
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Tested-by: NWilliam Dauchy <wdauchy@gmail.com>
Cc: stable@kernel.org
Cc: 675190@bugs.debian.org
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some architectures address spaces are set up in a way that this is
not necessary to work properly but on some others (like s390) it is.
Make sure we operate on the user address space to allow copy_xxx_user()
from the vhost_worker() thread by setting it explicitly before calling
use_mm() and revert it after unuse_mm().
Signed-off-by: NJens Freimann <jfrei@linux.vnet.ibm.com>
Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.

To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.

CC: <stable@vger.kernel.org>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds 10 device IDs for CP210x based devices from the following manufacturers:
Timewave
Clipsal
Festo
Link Instruments
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This device is also known as the Verizon USB551L.
Signed-off-by: NForest Bond <forest.bond@rapidrollout.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

USB phy layer driver are only built if usb host is selected, but they
are used too by USB_GADGET drivers
Signed-off-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch reverts the commit dba3c29e.

After bisecting, this commit dba3c29e is found to ruin micro-SD card data
(writing incorrect file, or fs is corrupt after several times mount)
on the beagle-xm revB, and reverting the commit will fix the problem.

Also from TRM of OMAP3/OMAP4/DM37x, the below is mentioned about
the Auto CMD12 Enable bit.
        - SDIO does not support this feature.
        - SD card only.
Looks it is not suitable to always enable Auto CMD12 in host controller
driver.

Considered that the commit is not mature enough, so ask to revert it
first.

Cc: Balaji T K <balajitk@ti.com>
Cc: Venkatraman S <svenkatr@ti.com>
Buglink: https://lkml.org/lkml/2012/6/10/225Reported-by: NPaolo Pisati <p.pisati@gmail.com>
Reported-bisected-and-tested-by: NMing Lei <ming.lei@canonical.com>
Signed-off-by: NMing Lei <ming.lei@canonical.com>
Acked-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

If multi block write operation fails for SD card, during
error handling we send the SD_APP_SEND_NUM_WR_BLKS (ACMD22)
to know how many blocks were already programmed by card.

But mmc_sd_num_wr_blocks() function which sends the ACMD22
calculates the data timeout value from csd.tacc_ns and
csd.tacc_clks parameters which will be 0 for block addressed
(>2GB cards) SD card. This would result in timeout_ns and
timeout_clks being 0 in the mmc_request passed to host driver.
This means host controller would program its data timeout timer
value with 0 which could result in DATA TIMEOUT errors from
controller.

To fix this issue, mmc_sd_num_wr_blocks() should instead
just call the mmc_set_data_timeout() to calculate the
data timeout value. mmc_set_data_timeout() function
ensures that non zero timeout value is set even for
block addressed SD cards.
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

nv_two_heads() was never meant to be used outside of pre-nv50 code.  The
code checks for >= NV_10 for 2 CRTCs, then downgrades a few specific
chipsets to 1 CRTC based on (pci_device & 0x0ff0).

The breakage example seen is on GTX 560Ti, with a pciid of 0x1200, which
gets detected as an NV20 (0x020x) with 1 CRTC by nv_two_heads(), causing
memory corruption because there's actually 2 CRTCs..

This switches fbcon to use the CRTC count directly from the mode_config
structure, which will also fix the same issue on Kepler boards which have
4 CRTCs.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

In current code, .list_voltage and .set_voltage_sel callbacks for BUCK7 and
BUCK8 return -EINVAL.

This patch adds s5m8767_buck78_ops for BUCK7 and BUCK8 which does not set
.list_voltage, .get_voltage_sel and .set_voltage_sel. ( This has the same
effect of returning -EINVAL in the callbacks)

Then for all the users of s5m8767_list_voltage, we don't need to worry about
the case reg_voltage_map[reg_id] is NULL.
So we can convert s5m8767_list_voltage to regulator_list_voltage_linear.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

If min_uV is in the range of: 3250001~3269999,
current code uses the equation:
        selector = DIV_ROUND_UP(min_uV - 1700000, 50000);
Then selector will be 32.
Then arizona_micsupp_list_voltage returns -EINVAL for this case which is wrong.

This patch fixes this issue:
If min_uV > 3200000, selector should be ARIZONA_MICSUPP_MAX_SELECTOR.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>