* 'upstream' of git://git.linux-mips.org/pub/scm/upstream-linus: (29 commits)
  MIPS: Call oops_enter, oops_exit in die
  staging/octeon: Software should check the checksum of no tcp/udp packets
  MIPS: Octeon: Enable C0_UserLocal probing.
  MIPS: No branches in delay slots for huge pages in handle_tlbl
  MIPS: Don't clobber CP0_STATUS value for CONFIG_MIPS_MT_SMTC
  MIPS: Octeon: Select CONFIG_HOLES_IN_ZONE
  MIPS: PM: Use struct syscore_ops instead of sysdevs for PM (v2)
  MIPS: Compat: Use 32-bit wrapper for compat_sys_futex.
  MIPS: Do not use EXTRA_CFLAGS
  MIPS: Alchemy: DB1200: Disable cascade IRQ in handler
  SERIAL: Lantiq: Set timeout in uart_port
  MIPS: Lantiq: Fix setting the PCI bus speed on AR9
  MIPS: Lantiq: Fix external interrupt sources
  MIPS: tlbex: Fix build error in R3000 code.
  MIPS: Alchemy: Include Au1100 in PM code.
  MIPS: Alchemy: Fix typo in MAC0 registration
  MIPS: MSP71xx: Fix build error.
  MIPS: Handle __put_user() sleeping.
  MIPS: Allow forced irq threading
  MIPS: i8259: Mark cascade interrupt non-threaded
  ...

* git://github.com/davem330/net:
  net: fix typos in Documentation/networking/scaling.txt
  bridge: leave carrier on for empty bridge
  netfilter: Use proper rwlock init function
  tcp: properly update lost_cnt_hint during shifting
  tcp: properly handle md5sig_pool references
  macvlan/macvtap: Fix unicast between macvtap interfaces in bridge mode

In summary, this DMI quirk uses the _CRS info by default for the ASUS
M2V-MX SE by turning on `pci=use_crs` and is similar to the quirk
added by commit 2491762c ("x86/PCI: use host bridge _CRS info on
ASRock ALiveSATA2-GLAN") whose commit message should be read for further
information.

Since commit 3e3da00c ("x86/pci: AMD one chain system to use pci
read out res") Linux gives the following oops:

    parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
    HDA Intel 0000:20:01.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
    HDA Intel 0000:20:01.0: setting latency timer to 64
    BUG: unable to handle kernel paging request at ffffc90011c08000
    IP: [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    PGD 13781a067 PUD 13781b067 PMD 1300ba067 PTE 800000fd00000173
    Oops: 0009 [#1] SMP
    last sysfs file: /sys/module/snd_pcm/initstate
    CPU 0
    Modules linked in: snd_hda_intel(+) snd_hda_codec snd_hwdep snd_pcm_oss snd_mixer_oss snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event tpm_tis tpm snd_seq tpm_bios psmouse parport_pc snd_timer snd_seq_device parport processor evdev snd i2c_viapro thermal_sys amd64_edac_mod k8temp i2c_core soundcore shpchp pcspkr serio_raw asus_atk0110 pci_hotplug edac_core button snd_page_alloc edac_mce_amd ext3 jbd mbcache sha256_generic cryptd aes_x86_64 aes_generic cbc dm_crypt dm_mod raid1 md_mod usbhid hid sg sd_mod crc_t10dif sr_mod cdrom ata_generic uhci_hcd sata_via pata_via libata ehci_hcd usbcore scsi_mod via_rhine mii nls_base [last unloaded: scsi_wait_scan]
    Pid: 1153, comm: work_for_cpu Not tainted 2.6.37-1-amd64 #1 M2V-MX SE/System Product Name
    RIP: 0010:[<ffffffffa0578402>]  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
    RSP: 0018:ffff88013153fe50  EFLAGS: 00010286
    RAX: ffffc90011c08000 RBX: ffff88013029ec00 RCX: 0000000000000006
    RDX: 0000000000000000 RSI: 0000000000000246 RDI: 0000000000000246
    RBP: ffff88013341d000 R08: 0000000000000000 R09: 0000000000000040
    R10: 0000000000000286 R11: 0000000000003731 R12: ffff88013029c400
    R13: 0000000000000000 R14: 0000000000000000 R15: ffff88013341d090
    FS:  0000000000000000(0000) GS:ffff8800bfc00000(0000) knlGS:00000000f7610ab0
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: ffffc90011c08000 CR3: 0000000132f57000 CR4: 00000000000006f0
    DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
    DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
    Process work_for_cpu (pid: 1153, threadinfo ffff88013153e000, task ffff8801303c86c0)
    Stack:
     0000000000000005 ffffffff8123ad65 00000000000136c0 ffff88013029c400
     ffff8801303c8998 ffff88013341d000 ffff88013341d090 ffff8801322d9dc8
     ffff88013341d208 0000000000000000 0000000000000000 ffffffff811ad232
    Call Trace:
     [<ffffffff8123ad65>] ? __pm_runtime_set_status+0x162/0x186
     [<ffffffff811ad232>] ? local_pci_probe+0x49/0x92
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afc5>] ? do_work_for_cpu+0x0/0x1b
     [<ffffffff8105afd0>] ? do_work_for_cpu+0xb/0x1b
     [<ffffffff8105fd3f>] ? kthread+0x7a/0x82
     [<ffffffff8100a824>] ? kernel_thread_helper+0x4/0x10
     [<ffffffff8105fcc5>] ? kthread+0x0/0x82
     [<ffffffff8100a820>] ? kernel_thread_helper+0x0/0x10
    Code: f4 01 00 00 ef 31 f6 48 89 df e8 29 dd ff ff 85 c0 0f 88 2b 03 00 00 48 89 ef e8 b4 39 c3 e0 8b 7b 40 e8 fc 9d b1 e0 48 8b 43 38 <66> 8b 10 66 89 14 24 8b 43 14 83 e8 03 83 f8 01 77 32 31 d2 be
    RIP  [<ffffffffa0578402>] azx_probe+0x3ad/0x86b [snd_hda_intel]
     RSP <ffff88013153fe50>
    CR2: ffffc90011c08000
    ---[ end trace 8d1f3ebc136437fd ]---

Trusting the ACPI _CRS information (`pci=use_crs`) fixes this problem.

    $ dmesg | grep -i crs # with the quirk
    PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug

The match has to be against the DMI board entries though since the vendor entries are not populated.

    DMI: System manufacturer System Product Name/M2V-MX SE, BIOS 0304    10/30/2007

This quirk should be removed when `pci=use_crs` is enabled for machines
from 2006 or earlier or some other solution is implemented.

Using coreboot [1] with this board the problem does not exist but this
quirk also does not affect it either. To be safe though the check is
tightened to only take effect when the BIOS from American Megatrends is
used.

        15:13 < ruik> but coreboot does not need that
        15:13 < ruik> because i have there only one root bus
        15:13 < ruik> the audio is behind a bridge

        $ sudo dmidecode
        BIOS Information
                Vendor: American Megatrends Inc.
                Version: 0304
                Release Date: 10/30/2007

[1] http://www.coreboot.org/

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=30552

Cc: stable@kernel.org (2.6.34)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: x86@kernel.org
Signed-off-by: NPaul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The second hunk fixes rps_sock_flow_table but has to re-wrap the paragraph.
Signed-off-by: NBenjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This resolves a regression seen by some users of bridging.
Some users use the bridge like a dummy device.
They expect to be able to put an IPv6 address on the device
with no ports attached. Although there are better ways of doing
this, there is no reason to not allow it.

Note: the bridge still will reflect the state of ports in the
bridge if there are any added.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of http://people.redhat.com/agk/git/linux-dm:
  dm crypt: always disable discard_zeroes_data
  dm: raid fix write_mostly arg validation
  dm table: avoid crash if integrity profile changes
  dm: flakey fix corrupt_bio_byte error path

* 'for-linus' of git://neil.brown.name/md:
  md: Avoid waking up a thread after it has been freed.

Replace the open coded initialization with the init function.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NHans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* 'for-linus' of git://github.com/dtor/input:
  Input: wacom - revert "Cintiq 21UX2 does not have menu strips"

* git://bedivere.hansenpartnership.com/git/scsi-rc-fixes-2.6:
  [SCSI] libsas: fix panic when single phy is disabled on a wide port
  [SCSI] qla2xxx: Fix crash in qla2x00_abort_all_cmds() on unload

This reverts commit 71c86ce5.
The 21UX2 does have touchstrips, but they are in a somewhat-
hidden location.
Signed-off-by: NJason Gerecke <killertofu@gmail.com>
Acked-by: NPing Cheng <pinglinux@gmail.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

lost_skb_hint is used by tcp_mark_head_lost() to mark the first unhandled skb.
lost_cnt_hint is the number of packets or sacked packets before the lost_skb_hint;
When shifting a skb that is before the lost_skb_hint, if tcp_is_fack() is ture,
the skb has already been counted in the lost_cnt_hint; if tcp_is_fack() is false,
tcp_sacktag_one() will increase the lost_cnt_hint. So tcp_shifted_skb() does not
need to adjust the lost_cnt_hint by itself. When shifting a skb that is equal to
lost_skb_hint, the shifted packets will not be counted by tcp_mark_head_lost().
So tcp_shifted_skb() should adjust the lost_cnt_hint even tcp_is_fack(tp) is true.
Signed-off-by: NZheng Yan <zheng.z.yan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tcp_v4_clear_md5_list() assumes that multiple tcp md5sig peers
only hold one reference to md5sig_pool. but tcp_v4_md5_do_add()
increases use count of md5sig_pool for each peer. This patch
makes tcp_v4_md5_do_add() only increases use count for the first
tcp md5sig peer.
Signed-off-by: NZheng Yan <zheng.z.yan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets should always be forwarded to the lowerdev using dev_forward_skb.
vlan->forward is for packets being forwarded directly to another macvlan/
macvtap device (used for multicast in bridge mode).
Reported-and-tested-by: NShlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: NDavid Ward <david.ward@ll.mit.edu>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

* git://github.com/davem330/net:
  pch_gbe: Fixed the issue on which a network freezes
  pch_gbe: Fixed the issue on which PC was frozen when link was downed.
  make PACKET_STATISTICS getsockopt report consistently between ring and non-ring
  net: xen-netback: correctly restart Tx after a VM restore/migrate
  bonding: properly stop queuing work when requested
  can bcm: fix incomplete tx_setup fix
  RDSRDMA: Fix cleanup of rds_iw_mr_pool
  net: Documentation: Fix type of variables
  ibmveth: Fix oops on request_irq failure
  ipv6: nullify ipv6_ac_list and ipv6_fl_list when creating new socket
  cxgb4: Fix EEH on IBM P7IOC
  can bcm: fix tx_setup off-by-one errors
  MAINTAINERS: tehuti: Alexander Indenbaum's address bounces
  dp83640: reduce driver noise
  ptp: fix L2 event message recognition

* 'fix/asoc' of git://github.com/tiwai/sound:
  ASoC: omap_mcpdm_remove cannot be __devexit
  ASoC: Fix setting update bits for WM8753_LADC and WM8753_RADC
  ASoC: use a valid device for dev_err() in Zylonite

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon/kms: fix channel_remap setup (v2)
  drm/radeon: Set cursor x/y to 0 when x/yorigin > 0.
  drm/radeon: Update AVIVO cursor coordinate origin before x/yorigin calculation.
  drm/radeon: Simplify cursor x/yorigin calculation.
  drm/radeon/kms: fix cursor image off-by-one error
  drm/radeon/kms: Fix logic error in DP HPD handler
  drm/radeon/kms: add retry limits for native DP aux defer
  drm/radeon/kms: fix regression in DP aux defer handling

* 'spi/merge' of git://git.secretlab.ca/git/linux-2.6:
  spi-topcliff-pch: Fix overrun issue
  spi-topcliff-pch: Add recovery processing in case FIFO overrun error occurs
  spi-topcliff-pch: Fix CPU read complete condition issue
  spi-topcliff-pch: Fix SSN Control issue
  spi-topcliff-pch: add tx-memory clear after complete transmitting

Add the ability to disable PCI-E MPS turning and using the BIOS
configured MPS defaults.  Due to the number of issues recently
discovered on some x86 chipsets, make this the default behavior.

Also, add the option for peer to peer DMA MPS configuration.  Peer to
peer DMA is outside the scope of this patch, but MPS configuration could
prevent it from working by having the MPS on one root port different
than the MPS on another.  To work around this, simply make the system
wide MPS the smallest possible value (128B).
Signed-off-by: NJon Mason <mason@myri.com>
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Most asics just use the hw default value which requires
no explicit programming.  For those that need a different
value, the vbios will program it properly.  As such,
there's no need to program these registers explicitly
in the driver.  Changing MC_SHARED_CHREMAP requires a reload
of all data in vram otherwise its contents will be scambled.

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=40103

v2: drop now unused channel_remap functions.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

We found that adding load, Rx data sometimes drops.(with DMA transfer mode)
The cause is that before starting Rx-DMA processing, Tx-DMA processing starts.
This causes FIFO overrun occurs.

This patch fixes the issue by modifying FIFO tx-threshold and DMA descriptor
size like below.

                      Current                   this patch
Rx-descriptor   4Byte+12Byte*341    -->    12Byte*340-4Byte-12Byte
Rx-threshold                   (Not modified)
Tx-descriptor   4Byte+12Byte*341    -->    16Byte-12Byte*340
Rx-threshold    12Byte              -->    2Byte
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Add recovery processing in case FIFO overrun error occurs with DMA transfer mode.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

We found Rx data sometimes drops.(with non-DMA transfer mode)
The cause is read complete condition is not true.

This patch fixes the issue.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

During processing 1 command/data series,
SSN should keep LOW.
However, currently, SSN becomes HIGH.
This patch fixes the issue.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Currently, in case of reading date from SPI flash,
command is sent twice.
The cause is that tx-memory clear processing is missing .
This patch adds the tx-momory clear processing.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Commit 2a7fade7 ("hwmon: lis3: Power on corrections") caused a
regression on HP laptops with 8bit chip.  Writing CTRL2_BOOT_8B bit seems
clearing the BIOS setup, and no proper interrupt for DriveGuard will be
triggered any more.

Since the init code there is basically only for embedded devices, put a
pdata check so that the problematic initialization will be skipped for
hp_accel stuff.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Samu Onkalo <samu.p.onkalo@nokia.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@google.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'hwmon-for-linus' of git://github.com/groeck/linux:
  hwmon: (coretemp) Avoid leaving around dangling pointer
  hwmon: (coretemp) Fixup platform device ID change

* git://github.com/davem330/ide:
  ide-disk: Fix request requeuing

* 'btrfs-3.0' of git://github.com/chrismason/linux:
  Btrfs: force a page fault if we have a shorty copy on a page boundary

Simon Kirby reported that on his RAID setup with idedisk underneath
the box OOMs after a couple of days of runtime. Running with
CONFIG_DEBUG_KMEMLEAK pointed to idedisk_prep_fn() which unconditionally
allocates an ide_cmd struct. However, ide_requeue_and_plug() can be
called more than once per request, either from the request issue or the
IRQ handler path and do blk_peek_request() ends up in idedisk_prep_fn()
repeatedly, allocating a struct ide_cmd everytime and "forgetting" the
previous pointer.

Make sure the code reuses the old allocated chunk.
Reported-and-tested-by: NSimon Kirby <sim@hostway.ca>
Cc: <stable@kernel.org> [ 39.x, 3.0.x ]
Link: http://marc.info/?l=linux-kernel&m=131667641517919
Link: http://lkml.kernel.org/r/20110922072643.GA27232@hostway.caSigned-off-by: NBorislav Petkov <bp@alien8.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pch_gbe driver has an issue which a network stops,
when receiving traffic is high.
In the case, The link down and up are necessary to return a network.

This patch fixed this issue.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link was downed during network use,
there is an issue on which PC freezes.

This patch fixed this issue.
Signed-off-by: NToshiharu Okada <toshiharu-linux@dsn.okisemi.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a minor change.

Up until kernel 2.6.32, getsockopt(fd, SOL_PACKET, PACKET_STATISTICS,
...) would return total and dropped packets since its last invocation. The
introduction of socket queue overflow reporting [1] changed drop
rate calculation in the normal packet socket path, but not when using a
packet ring. As a result, the getsockopt now returns different statistics
depending on the reception method used. With a ring, it still returns the
count since the last call, as counts are incremented in tpacket_rcv and
reset in getsockopt. Without a ring, it returns 0 if no drops occurred
since the last getsockopt and the total drops over the lifespan of
the socket otherwise. The culprit is this line in packet_rcv, executed
on a drop:

drop_n_acct:
        po->stats.tp_drops = atomic_inc_return(&sk->sk_drops);

As it shows, the new drop number it taken from the socket drop counter,
which is not reset at getsockopt. I put together a small example
that demonstrates the issue [2]. It runs for 10 seconds and overflows
the queue/ring on every odd second. The reported drop rates are:
ring: 16, 0, 16, 0, 16, ...
non-ring: 0, 15, 0, 30, 0, 46, 0, 60, 0 , 74.

Note how the even ring counts monotonically increase. Because the
getsockopt adds tp_drops to tp_packets, total counts are similarly
reported cumulatively. Long story short, reinstating the original code, as
the below patch does, fixes the issue at the cost of additional per-packet
cycles. Another solution that does not introduce per-packet overhead
is be to keep the current data path, record the value of sk_drops at
getsockopt() at call N in a new field in struct packetsock and subtract
that when reporting at call N+1. I'll be happy to code that, instead,
it's just more messy.

[1] http://patchwork.ozlabs.org/patch/35665/
[2] http://kernel.googlecode.com/files/test-packetsock-getstatistics.cSigned-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a VM is saved and restored (or migrated) the netback driver will no
longer process any Tx packets from the frontend.  xenvif_up() does not
schedule the processing of any pending Tx requests from the front end
because the carrier is off.  Without this initial kick the frontend
just adds Tx requests to the ring without raising an event (until the
ring is full).

This was caused by 47103041 (net:
xen-netback: convert to hw_features) which reordered the calls to
xenvif_up() and netif_carrier_on() in xenvif_connect().
Signed-off-by: NDavid Vrabel <david.vrabel@citrix.com>
Cc: Ian Campbell <ian.campbell@citrix.com>
Acked-by: NIan Campbell <ian.campbell@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During a test where a pair of bonding interfaces using ARP monitoring
were both brought up and torn down (with an rmmod) repeatedly, a panic
in the timer code was noticed.  I tracked this down and determined that
any of the bonding functions that ran as workqueue handlers and requeued
more work might not properly exit when the module was removed.

There was a flag protected by the bond lock called kill_timers that is
set when the interface goes down or the module is removed, but many of
the functions that monitor link status now unlock the bond lock to take
rtnl first.  There is a chance that another CPU running the rmmod could
get the lock and set kill_timers after the first check has passed.

This patch does not allow any function to queue work that will make
itself run unless kill_timers is not set.  I also noticed while doing
this work that bond_resend_igmp_join_requests did not have a check for
kill_timers, so I added the needed call there as well.
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Reported-by: NLiang Zheng <lzheng@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apart from the obvious cleanup, this should make the line

			cursor_end = x - xorigin + w;

correct now.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixes cursor disappearing prematurely when moving off a top/left edge which
is not located at the desktop top/left edge.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The mouse cursor hotspot calculation when the cursor is partially off the
top or left side of the screen was off by one.

Fixes https://bugs.freedesktop.org/show_bug.cgi?id=41158Signed-off-by: NNicholas Miell <nmiell@gmail.com>
Reviewed-by: NMichel Dänzer <michel@daenzer.net>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>