Merge branches 'at91', 'dyntick', 'ep93xx', 'iop', 'ixp', 'misc', 'orion', 'omap-reviewed', 'rpc', 'rtc' and 's3c' into devel

Signed-off-by: NDmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

at91sam9g20 defconfig file
Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.

AT91sam9g20 is an evolution of the at91sam9260 with a faster clock
speed.
We created a new board for this device but based the chip support
directly on 9260 files with little updates.
Here is the chip page on Atmel wabsite:
http://atmel.com/dyn/products/product_card.asp?part_id=4337Signed-off-by: NSedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: NJustin Waters <justin.waters@timesys.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch brings support for gpio/gpiolib framework to Intel IOP3xx
platforms.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

[ARM] at91: Fix NAND FLASH timings for at91sam9x evaluation kits.

New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf).
Signed-off-by: NPatrice Vilchez <patrice.vilchez@atmel.com>
Acked-by: NAndrew Victor <linux@maxim.org.za>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

On Feroceon platforms that have a branch prediction unit, bit 11 of the
cp15 control register controls the BPU.  This patch keeps the old value
of this bit instead of always clearing it.
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The HP mv2120 has several LEDs that are controlled through gpio.
Export the health LED, the red SATA LEDs as well as two gpios
that control the brightness of _all_ LEDs to userland.  The
Ethernet and power LEDs can't be controlled through gpio and the
blue SATA LEDs are handled via the SATA driver.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This patch adds support for the Marvell Orion-VoIP RD-88F5181L-FXO
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

This patch adds support for the Marvell Orion-VoIP RD2-88F5181L-GE
Reference Design, and enables use of the ethernet, USB, Cardbus and
mini-PCIe ports.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Signed-off-by: NImre Kaloz <kaloz@openwrt.org>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Update the s3c2410_defconfig for the current set of
added patches.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Minor style fixes.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Initialise the hardware register settings on boot, to allow the
device to function correctly.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

This patch adds the configuration needed for the LCD display on the n30.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the Acer N35 and related devices.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the LEDs on the Acer N30.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the GPIO buttons on the Acer N30.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for the USB D+ pull up on the Acer N30.  This is needed
for the USB gadget to work properly.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Clean up some junk from the official kernel.

The compile-command is something that's only useful for me personally
and doesn't belong in the mainstream kernel.
Signed-off-by: NChrister Weinigel <christer@weinigel.se>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Update the S3C2443 clock support to add the prediv clock
that is sourced via a divider from msysclk. Also fix the
setting of p and h clocks from this prediv clock.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the armdiv and arm clocks to the S3C2443 clock
framework and ensure they are correctly setup.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

s3c2443_clkcon_enable_p() was reading from the correct register
S3C2443_PCLKCON, but then writing the value back to the wrong
register S3C2443_HCLKCON.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add DM9000AEP network controller support for AT2440EVB.
Signed-off-by: NRamax Lo <ramaxlo@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add basic support for AT2440EVB board based on Samsung S3C2440 SoC.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NRamax Lo <ramaxlo@gmail.com>

Update mach-types.  Remove invalid or incorrect entries.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The S3C2410 serial driver in drivers/serial/s3c2410.c has been
growing bigger with the addition of more variants of this hardware
with the growing Samsung SoCs range. As such, it would be
easier to split this code up into a core and per-cpu drivers to
make driver addition easier, and the core smaller.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for PWM in the S3C24XX series of SoC via the
PWM API.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

For s3c2412, set parent for clk_erefclk and clk_urefclk.
This allow for example to use xtal or extclk for i2s clock.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NMatthieu Castet <matthieu.castet@parrot.com>

Add tmp101 support via the new style I2C driver registration
on the VR1000.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add i2c board info initialiser to setup the list of
I2C devices present on an Simtec Anubis.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add i2c board intialisers to specify the I2C devices
attached on the Thorcom VR1000.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add i2c boardinfo for the connected i2c devices on the
Simtec Bast.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add an i2c board information initialisers to the board
to define which devices are present.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move to using the physmap platform device code to attached NOR
flash on Simtec boards so that the old bast-flash driver can be
safely removed.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change the (as yet unused) IDE bus on the Simtec Anubis board
to use pata_platform and thus libata to provide IDE support.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Use the pata_platform driver to provide the IDE port
drivers on the Simntec BAST and Thorcom VR1000 machines
as a precursor to removing drivers/ide/arm/bast-ide.c

This will mean that the system will need SCSI and SCSI disc
support as a minimum, and any references to hdX will be
changed to sdX.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add pm_power_off hook to allow the Logitech Jive to shutdown
when asked to halt.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>